I wonder why we need this bitmask indexing into zone->node_zonelists[]?

We always start with the highest zone and then include all lower zones
if we build zonelists.

Are there really cases where we need allocation from ZONE_DMA or
ZONE_HIGHMEM but not ZONE_NORMAL? It seems that the current implementation
of highest_zone() makes that already impossible.

If we go linear on the index then gfp_zone() == highest_zone() and a lot
of definitions fall by the wayside.

We can now revert back to the use of gfp_zone() in mempolicy.c ;-)
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

There is a check in zonelist_policy that compares pieces of the bitmap
obtained from a gfp mask via GFP_ZONETYPES with a zone number in function
zonelist_policy().

The bitmap is an ORed mask of __GFP_DMA, __GFP_DMA32 and __GFP_HIGHMEM.
The policy_zone is a zone number with the possible values of ZONE_DMA,
ZONE_DMA32, ZONE_HIGHMEM and ZONE_NORMAL. These are two different domains
of values.

For some reason seemed to work before the zone reduction patchset (It
definitely works on SGI boxes since we just have one zone and the check
cannot fail).

With the zone reduction patchset this check definitely fails on systems
with two zones if the system actually has memory in both zones.

This is because ZONE_NORMAL is selected using no __GFP flag at
all and thus gfp_zone(gfpmask) == 0. ZONE_DMA is selected when __GFP_DMA
is set. __GFP_DMA is 0x01.  So gfp_zone(gfpmask) == 1.

policy_zone is set to ZONE_NORMAL (==1) if ZONE_NORMAL and ZONE_DMA are
populated.

For ZONE_NORMAL gfp_zone(<no _GFP_DMA>) yields 0 which is <
policy_zone(ZONE_NORMAL) and so policy is not applied to regular memory
allocations!

Instead gfp_zone(__GFP_DMA) == 1 which results in policy being applied
to DMA allocations!

What we realy want in that place is to establish the highest allowable
zone for a given gfp_mask. If the highest zone is higher or equal to the
policy_zone then memory policies need to be applied. We have such
a highest_zone() function in page_alloc.c.

So move the highest_zone() function from mm/page_alloc.c into
include/linux/gfp.h.  On the way we simplify the function and use the new
zone_type that was also introduced with the zone reduction patchset plus we
also specify the right type for the gfp flags parameter.
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Signed-off-by: NLee Schermerhorn <Lee.Schermerhorn@hp.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Make ZONE_HIGHMEM optional

- ifdef out code and definitions related to CONFIG_HIGHMEM

- __GFP_HIGHMEM falls back to normal allocations if there is no
  ZONE_HIGHMEM

- GFP_ZONEMASK becomes 0x01 if there is no DMA32 and no HIGHMEM
  zone.

[jdike@addtoit.com: build fix]
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Signed-off-by: NChristoph Lameter <clameter@engr.sgi.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Make ZONE_DMA32 optional

- Add #ifdefs around ZONE_DMA32 specific code and definitions.

- Add CONFIG_ZONE_DMA32 config option and use that for x86_64
  that alone needs this zone.

- Remove the use of CONFIG_DMA_IS_DMA32 and CONFIG_DMA_IS_NORMAL
  for ia64 and fix up the way per node ZVCs are calculated.

- Fall back to prior GFP_ZONEMASK of 0x03 if there is no
  DMA32 zone.
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Introduce GFP_NOWAIT, as an alias for GFP_ATOMIC & ~__GFP_HIGH.

This also changes XFS, which is the only in-tree user of this idiom that I
could find.  The XFS piece is compile-tested only.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Acked-by: NNathan Scott <nathans@sgi.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The cache reaper currently tries to free all alien caches and all remote
per cpu pages in each pass of cache_reap.  For a machines with large number
of nodes (such as Altix) this may lead to sporadic delays of around ~10ms.
Interrupts are disabled while reclaiming creating unacceptable delays.

This patch changes that behavior by adding a per cpu reap_node variable.
Instead of attempting to free all caches, we free only one alien cache and
the per cpu pages from one remote node.  That reduces the time spend in
cache_reap.  However, doing so will lengthen the time it takes to
completely drain all remote per cpu pagesets and all alien caches.  The
time needed will grow with the number of nodes in the system.  All caches
are drained when they overflow their respective capacity.  So the drawback
here is only that a bit of memory may be wasted for awhile longer.

Details:

1. Rename drain_remote_pages to drain_node_pages to allow the specification
   of the node to drain of pcp pages.

2. Add additional functions init_reap_node, next_reap_node for NUMA
   that manage a per cpu reap_node counter.

3. Add a reap_alien function that reaps only from the current reap_node.

For us this seems to be a critical issue.  Holdoffs of an average of ~7ms
cause some HPC benchmarks to slow down significantly.  F.e.  NAS parallel
slows down dramatically.  NAS parallel has a 12-16 seconds runtime w/o rotor
compared to 5.8 secs with the rotor patches.  It gets down to 5.05 secs with
the additional interrupt holdoff reductions.
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Following kmalloc_node.

Needed for another patch to return -1 for unknown nodes in x86-64.

Cc: Christoph Lameter <clameter@engr.sgi.com>
Cc: kiran@scalex86.org
Signed-off-by: NAndi Kleen <ak@suse.de>
[ Changed 0 to numa_node_id() on suggestion by Christoph Lameter ]
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Clarify in comments that GFP_ATOMIC means both "don't sleep" and "use
emergency pools", hence both ALLOC_HARDER and ALLOC_HIGH.
Signed-off-by: NPaul Jackson <pj@sgi.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

There was some confusion about the different zone usage, this should fix
up the resulting mess in the GFP zonemask handling.

The different zone usage is still confusing (it's very easy to mix up
the individual zone numbers with the GFP zone _list_ numbers), so we
might want to clean up some of this in the future, but in the meantime
this should fix the actual problems.
Acked-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add a new 4GB GFP_DMA32 zone between the GFP_DMA and GFP_NORMAL zones.

As a bit of historical background: when the x86-64 port
was originally designed we had some discussion if we should
use a 16MB DMA zone like i386 or a 4GB DMA zone like IA64 or
both. Both was ruled out at this point because it was in early
2.4 when VM is still quite shakey and had bad troubles even
dealing with one DMA zone.  We settled on the 16MB DMA zone mainly
because we worried about older soundcards and the floppy.

But this has always caused problems since then because
device drivers had trouble getting enough DMA able memory. These days
the VM works much better and the wide use of NUMA has proven
it can deal with many zones successfully.

So this patch adds both zones.

This helps drivers who need a lot of memory below 4GB because
their hardware is not accessing more (graphic drivers - proprietary
and free ones, video frame buffer drivers, sound drivers etc.).
Previously they could only use IOMMU+16MB GFP_DMA, which
was not enough memory.

Another common problem is that hardware who has full memory
addressing for >4GB misses it for some control structures in memory
(like transmit rings or other metadata).  They tended to allocate memory
in the 16MB GFP_DMA or the IOMMU/swiotlb then using pci_alloc_consistent,
but that can tie up a lot of precious 16MB GFPDMA/IOMMU/swiotlb memory
(even on AMD systems the IOMMU tends to be quite small) especially if you have
many devices.  With the new zone pci_alloc_consistent can just put
this stuff into memory below 4GB which works better.

One argument was still if the zone should be 4GB or 2GB. The main
motivation for 2GB would be an unnamed not so unpopular hardware
raid controller (mostly found in older machines from a particular four letter
company) who has a strange 2GB restriction in firmware. But
that one works ok with swiotlb/IOMMU anyways, so it doesn't really
need GFP_DMA32. I chose 4GB to be compatible with IA64 and because
it seems to be the most common restriction.

The new zone is so far added only for x86-64.

For other architectures who don't set up this
new zone nothing changes. Architectures can set a compatibility
define in Kconfig CONFIG_DMA_IS_DMA32 that will define GFP_DMA32
as GFP_DMA. Otherwise it's a nop because on 32bit architectures
it's normally not needed because GFP_NORMAL (=0) is DMA able
enough.

One problem is still that GFP_DMA means different things on different
architectures. e.g. some drivers used to have #ifdef ia64  use GFP_DMA
(trusting it to be 4GB) #elif __x86_64__ (use other hacks like
the swiotlb because 16MB is not enough) ... . This was quite
ugly and is now obsolete.

These should be now converted to use GFP_DMA32 unconditionally. I haven't done
this yet. Or best only use pci_alloc_consistent/dma_alloc_coherent
which will use GFP_DMA32 transparently.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Remove last remnant of the defunct early reclaim page logic, the no longer
used __GFP_NORECLAIM flag bit.
Signed-off-by: NPaul Jackson <pj@sgi.com>
Acked-by: NMartin Hicks <mort@bork.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Beginning of gfp_t annotations:

 - -Wbitwise added to CHECKFLAGS
 - old __bitwise renamed to __bitwise__
 - __bitwise defined to either __bitwise__ or nothing, depending on
   __CHECK_ENDIAN__ being defined
 - gfp_t switched from __nocast to __bitwise__
 - force cast to gfp_t added to __GFP_... constants
 - new helper - gfp_zone(); extracts zone bits out of gfp_t value and casts
   the result to int
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

 - added typedef unsigned int __nocast gfp_t;

 - replaced __nocast uses for gfp flags with gfp_t - it gives exactly
   the same warnings as far as sparse is concerned, doesn't change
   generated code (from gcc point of view we replaced unsigned int with
   typedef) and documents what's going on far better.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add another GFP flag: __GFP_HARDWALL.

A subsequent "cpuset_zone_allowed" patch will use this flag to mark GFP_USER
allocations, and distinguish them from GFP_KERNEL allocations.

Allocations (such as GFP_USER) marked GFP_HARDWALL are constrainted to the
current tasks cpuset.  Other allocations (such as GFP_KERNEL) can steal from
the possibly larger nearest mem_exclusive cpuset ancestor, if memory is tight
on every node in the current cpuset.

This patch collides with Mel Gorman's patch to reduce fragmentation in the
standard buddy allocator, which adds two GFP flags.  This was discussed on
linux-mm in July.  Most likely, one of his flags for user reclaimable memory
can be the same as my __GFP_HARDWALL flag, under some generic name meaning its
user address space memory.
Signed-off-by: NPaul Jackson <pj@sgi.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The pageset array can potentially acquire a huge amount of memory on large
NUMA systems.  F.e.  on a system with 512 processors and 256 nodes there
will be 256*512 pagesets.  If each pageset only holds 5 pages then we are
talking about 655360 pages.With a 16K page size on IA64 this results in
potentially 10 Gigabytes of memory being trapped in pagesets.  The typical
cases are much less for smaller systems but there is still the potential of
memory being trapped in off node pagesets.  Off node memory may be rarely
used if local memory is available and so we may potentially have memory in
seldom used pagesets without this patch.

The slab allocator flushes its per cpu caches every 2 seconds.  The
following patch flushes the off node pageset caches in the same way by
tying into the slab flush.

The patch also changes /proc/zoneinfo to include the number of pages
currently in each pageset.
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

When using the early zone reclaim, it was noticed that allocating new pages
that should be spread across the whole system caused eviction of local pages.

This adds a new GFP flag to prevent early reclaim from happening during
certain allocation attempts.  The example that is implemented here is for page
cache pages.  We want page cache pages to be spread across the whole system,
and we don't want page cache pages to evict other pages to get local memory.
Signed-off-by: NMartin Hicks <mort@sgi.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Mempools have 2 problems.

The first is that mempool_alloc can possibly get stuck in __alloc_pages
when they should opt to fail, and take an element from their reserved pool.

The second is that it will happily eat emergency PF_MEMALLOC reserves
instead of going to their reserved pools.

Fix the first by passing __GFP_NORETRY in the allocation calls in
mempool_alloc.  Fix the second by introducing a __GFP_MEMPOOL flag which
directs the page allocator not to allocate from the reserve pool.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!