The revision is part of the pci_dev struct, so there is no need to read it in.

Stop storing the revision and latency in the chip struct, since they're never
used after being printed out when the driver loads.

linux/pci.h wasn't included.  It was getting picked up something else,
probably cx88.h, but this file uses struct pci_dev so it should include pci.h.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

channels_min should be 2, not 1.  The hardware only supports stereo.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Currently the driver turns on audio interrupts, then sets the audio interrupt
mask to select which interrupts to get.  One could received unwanted
interrupts since the mask is set _after_ interrupts have already been turned
on.  Change the order of the operations, and clear any audio interrupt status
bits that are already set for good measure.

Before changing the SRAM FIFO parameters, make sure the FIFO isn't being used.
This shouldn't happen with just the ALSA driver, as it should never try to
turn on FIFO/RISC/DMA while they are already on.  However, the V4L driver
needs to turn the audio FIFO on for analog audio output to work (undocumented
cx88 bug).  The FIFO parameters are in an inconsistent state while they are
updated, and this results in many FIFO sync error IRQs if the FIFO is in use
while it's in this inconsistent state.

Also create and use a bunch of symbolic constants for audio interrupt mask
bits.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When an irq handled by the cx88 core driver (currently IR and errors) occurs
and the cx88-alsa irq handler is the first called, it will claim to have
handled the irq but it doesn't call cx88_core_irq() to handle it.

The means loading cx88-alsa can disable the IR remote.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Used for the PCI_INTMSK and PCI_INT_STAT registers.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add VIDIOC_OVERLAY to enable/disable the OSD. Also add the OSD state to the
log status report.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The return value of ivtv_udma_fill_sg_list() was changed by the
highmem bugfix, but that return value was still used in ivtv-yuv.c.

Revert to the old return value, but in addition return -1 in case of
a memory allocation error.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When trying to DMA userspace buffers to the cx23415 you need to check
whether the page is in highmem. If this is the case, then bounce buffers
have to be used to allow DMA.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Serialization is now done on the open/close/ioctl level and also when the
read/write/poll start an encoder/decoder stream.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- add FILE debug flag for open/close/read/write/poll.
- show cmd for encoder/decoder command ioctl.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Some streams (PCM, VBI decoding) do not need that much memory, so specify
the allocated memory in kB instead of MB to limit memory usage. E.g. 1 MB
is overkill for the VBI decoding stream, 64 kB is enough.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The TV output standard was set only on first use, which meant that the saa7127
was set to NTSC until then, leading to flickering on PAL systems.

Since the saa7127 has no firmware it is OK to initialize it immediately.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Whenever the 0x80b register is used the microcontroller should be reset.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- Give up frame after three retries.
- When the last capture/decode ends, make sure to delete the dma_timer.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- Invalid VBI packets should result in an empty VBI frame, not
  in an zero-sized frame that causes the reader to incorrectly
  return a 0 (EOF) value.
- PIO completion should not reset the sg_pending_size field.
- The DMA offset detection code should be ignored for PIO transfers:
  it somehow messes up the data on the card and is not needed anyway
  for PIO.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

It turns out that the cx23415/6 DMA engine cannot do scatter/gather DMA
reliably. Every so often depending on the phase of the moon and your
hardware configuration the cx2341x DMA engine simply chokes on it and
you have to reboot to get it working again.

This change replaced the scatter/gather DMA by single transfers at a time,
where the driver is now responsible for DMA-ing each buffer.

UDMA is still done using scatter/gather DMA, that will be fixed soon.

Many thanks to Mark Bryars <mark.bryars@etvinteractive.com> for discovering
the link between scatter/gather and the DMA timeouts.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When there are no more free buffers, then buffers are stolen from the
predma queue. Buffers should be stolen from the head of that queue (which
is where the most recently added buffers are) and all buffers belonging
to a frame should be stolen. Otherwise 'half-frames' would remain in the
queue, which leads to ugly playback and complete sync failure for YUV
buffers.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The CX2341X_ENC_INITIALIZE_INPUT firmware call requires careful handling,
otherwise the computer can freeze or the top-third of the screen can start
flickering. This patch ensures that CX2341X_ENC_INITIALIZE_INPUT is called
at the right time and in the right way.

In addition the stop capture handling was improved so that the last pending
DMA transfer is also processed. Otherwise this would be the first data that
arrived when a new capture was started which is not what you want.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NKazuhiko Kawakami <kazz-0@mail.goo.ne.jp>
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Working with Nova-T Stick (70001) with remote control model A415.
Untested with other dib0700m/dib0700p devices.
Signed-off-by: NDarren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: NPatrick Boettcher <pb@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Typo fix in Nova-TD description
Signed-off-by: NDarren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: NPatrick Boettcher <pb@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Repair modinfo parameter descriptions for force_pid_filter_usage and
disable_rc_polling.
Signed-off-by: NMichael Mauch <michael.mauch@gmx.de>
Signed-off-by: NPatrick Boettcher <pb@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

There are now 4 different versions of the GENPIX USB adapter.  The 
newest 'Skywalker' models are fully self-contained, and need no 
additional hardware to be used.  A very reliable DVB-S card even without 
using any of the alternate modulatations (which this kernel module does 
not currently support)

The following patch adds support for all 4 versions of the genpix
adapter (www.genpix-electronics.com).

Signed-off-by: Alan Nisota alannisota@gmail.com
Signed-off-by: NPatrick Boettcher <pb@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

FM radio transmission use a preemphasis/deemphasis scheme to reduce
high-frequency noise.  The cx88 audio decoder is supposedly set to no
deemphasis by the current driver.

However, the "no deemphasis" setting doesn't work.  On my chip, cx23883, it
produces the same result as the 75 us time constant.  Maybe the default
settings on the cx23881 are for 50 us?

Since the deemphasis time constant varies by country, allow setting it via a
module parameter.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The first part of dvb_net_close() is just a cut&paste from
dvb_generic_release(), so maybe it would be better to just call
dvb_generic_release() instead?
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Acked-by: NMarkus Rechberger <mrechberger@gmail.com>
Acked-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The Coverity checker spotted that we'd have already oops'ed if "dev"
was NULL.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Get rid of the "CORE" prefix from cx88 printks.  It was only used a few times,
and it makes it look like they're coming from the kernel core or something.

Fix the message, "TV tuner 60 at 0x1fe, Radio tuner -1 at 0x1fe", by adding a
"cx88[0]" prefix to be consistent, and to keep people who grep their dmesg
output for cx88 from missing it.  Get rid of the addresses, which are always
wrong.  The addresses are always set to -1, but because it's an unsigned 8-bit
value, the left shift converts it to the nonsense address 0x1fe.

In the cx8802 driver, some cut and pasted code prefixed lines with "CORE
cx88[0]:", which has been changed to "cx88[0]/2:" like the other printks from
the cx8802 driver.

Also fix some ugly printks in the cx8802 driver that used __FUNCTION__ for
KERN_INFO and KERN_ERR messages.

The changed printks in cx88-mpeg.c also needed lots of whitespace and
80-column fixes.

A bunch of misc changes in cx88-dvb.c and cx88-video.c to add message levels
or a consistent "cx88[?]/2" or "cx88[?]/0" prefix.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

A lot of code in cx88-cards.c was only used by cx88-core.c when the core state
is first allocated and initialized.  Moving that task to cx88-cards makes the
driver simpler and the files more self contained.

- Module parameters tuner, radio, card, and latency move to cx88-cards.c
- cx88_boards is made static
- cx88_subids is made static and const
- cx88_bcount is eliminated
- cx88_idcount is eliminated
- cx88_card_list() is made static
- cx88_card_setup_pre_i2c() is made static
- cx88_card_setup() is made static
- cx88_pci_quirks() is moved from cx88-core to cx88-cards
  The function argument "char *name" is made const too
- get_ressources() is moved from cx88-core to cx88-cards, and renamed to
  cx88_get_resources()
- The code to allocate and initialize the core state struct and the chip is
  moved out of cx88-core.c:cx88_get_core() and into a new function in
  cx88-cards.c, cx88_core_create().  This makes both functions simpler.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The cx88 driver state stored the ID of the board type in core->board.  Every
time the driver need to get some information about the board configuration, it
uses the board number as an index into board configuration array.

This patch changes it so that the board number is in core->boardnr, and
core->board is a copy of the board configuration information.  This allows
access to board information without the extra indirection.  e.g.
cx88_boards[core->board].mpeg becomes core->board.mpeg.

This has a number of advantages:
- The code is simpler to write.

- It compiles to be smaller and faster, without needing the extra array lookup
  to get at the board information.

- The cx88_boards array no longer needs to be exported to all cx88 modules.

- The boards array can be made const

- It should be possible to avoid keeping the (large) cx88_boards array around
  after the module is loaded.

- If module parameters or eeprom info override some board configuration
  setting, it's not necessary to modify the boards array, which would
  affect all boards of the same type.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

An error message for PCI resource allocation failure used the board type
before it was set.  Just get rid of the error message, as get_ressources()
[sic] already prints one.  Format that error message better, and add the pci
function and subsystem information to better associate the error with what
caused it.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The vmux setting is only two bits, but was taking up a whole 32 
in the input description struct.  By changing it to a two-bit 
bitfield, it can fit in what was padding space before and drop 
the input size by 4 bytes, from 28 to 24. This drops the board 
description struct, which has 9 inputs, from 280 to 244 bytes.  
Total driver size decreases by 2108 bytes.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The currently used "struct class_device" will be removed from the
kernel. Here is a trivial patch that converts DVB to use struct device.
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

videobuf_read_stream is more efficient than videobuf_read_one
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Change io_st_le32() to use inline functions rather than
direct inline assembly code.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

"extern inline" will have different semantics with gcc 4.3.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

tuner-simple is the only sub-driver that uses last_div, so we 
can free up two bytes of memory for all other tuners, by moving 
this into tuner-simple's private data area.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>