drivers/ide/mips/au1xxx-ide.c:684: warning: ISO C90 forbids mixed declarations and code
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The driver wrongly takes the address setup time into account when calculating
the PIO recovery time -- this leads to slight overclocking of the PIO modes 0
and 1 (so, the prayers failed to help, as usual :-).  Rework the code to be
calculating recovery clock count as a difference between the total cycle count
and the active count (we don't need to calculate the recovery time itself since
it's not specified for the PIO modes 0 to 2, and for modes 3 and 4 this formula
gives enough recovery time anyway in the chip's supported PCI frequency range).

This patch has been inspired by reading the datasheets and looking at what the
libata driver does; it has been compile-tested only (as usual :-) but anyway,
the new code gives the same or longer recovery times than the old one...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

I finally found a dual core box, which survives suspend/resume without
crashing in the middle of nowhere. Sigh, I never figured out from the
code and the bug reports what's going on.

The observed hangs are caused by a stale state transition of the clock
event devices, which keeps the RCU synchronization away from completion,
when the non boot CPU is brought back up.

The suspend/resume in oneshot mode needs the similar care as the
periodic mode during suspend to RAM. My assumption that the state
transitions during the different shutdown/bringups of s2disk would go
through the periodic boot phase and then switch over to highres resp.
nohz mode were simply wrong.

Add the appropriate suspend / resume handling for the non periodic
modes.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [IPV6]: ipv6_fl_socklist is inadvertently shared.
  [TCP]: Fix tcp_mem[] initialization.
  [NET]: Copy mac_len in skb_clone() as well
  [IPV4]: Do not disable preemption in trie_leaf_remove().

* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC64]: Get DEBUG_PAGEALLOC working again.

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] Kconfig: Move missplaced NR_CPUS default from SMTC to VSMP.
  [MIPS] Lockdep: Fix recursion bug.
  [MIPS] RTLX: Handle copy_*_user return values.
  [MIPS] RTLX: Protect rtlx_{read,write} with mutex.
  [MIPS] RTLX: Harden against compiler reordering and optimization.
  [MIPS] RTLX: Don't use volatile; it's fragile.
  [MIPS] Lasat: Downgrade 64-bit kernel from experimental to broken.
  [MIPS] Compat: Fix build if CONFIG_SYSVIPC is disabled.
  [CHAR] lcd: Fix two warnings.
  [MIPS] FPU ownership management & preemption fixes
  [MIPS] Check FCSR for pending interrupts, alternative version
  [MIPS] IP27, IP35: Fix warnings.

The maximum seconds value we can handle on 32bit is LONG_MAX.

Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix typo in sync_constant_test_bit()'s name, so sync_bitops.h is consistent
with bitops.h
Signed-off-by: NJeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: NChris Wright <chrisw@sous-sol.org>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The set_cs field of struct s3c24xx_spi is declared as returning a int but
the value returned but set_cs is never fixed.  Moreover, the default
function for set_cs and the set_cs defintion in the platform data are
returning void.

I'm proposing to change the prototype to void (*set_cs)(...). By doing
this, I'm also fixing 2 build warnings:

  drivers/spi/spi_s3c24xx.c: In function 's3c24xx_spi_probe':
  drivers/spi/spi_s3c24xx.c:330: warning: assignment from incompatible pointer type
  drivers/spi/spi_s3c24xx.c:335: warning: assignment from incompatible pointer type
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This bug was seen on ppc64, but it could have occurred on any
architecture with a page size of 64k or above.  The problem is that in
fs/binfmt_elf.c:randomize_stack_top() randomizes the stack to within
0x7ff pages.  On 4k page machines, this is 8MB; on 64k page boxes, this
is 128MB.

The problem is that the new binary layout (selected in
arch_pick_mmap_layout) places the mapping segment 128MB or the stack
rlimit away from the top of the process memory, whichever is larger.  If
you chose an rlimit of less than 128MB (most defaults are in the 8Mb
range) then you can end up having your entire stack randomized away.

The fix is to make randomize_stack_top() only steal at most 8MB, which this
patch does.  However, I have to point out that even with this, your stack
rlimit might not be exactly what you get if it's > 128MB, because you're
still losing the random offset of up to 8MB.

The true fix should be to leave an explicit gap for the randomization plus
a buffer when determining mmap_base, but that would involve fixing all the
architectures.

Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixes a bogus lockdep warning which causes lockdep to disable itself.
Acked-by: NIngo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Looking at oom_kill.c, found that the intention to not kill the selected
process if any of its children/siblings has OOM_DISABLE set, is not being
met.
Signed-off-by: NAnkita Garg <ankita@in.ibm.com>
Acked-by: NNick Piggin <npiggin@suse.de>
Acked-by: NWilliam Irwin <wli@holomorphy.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove the misleading "Presently only useful on the IA-64 platform" text
from the EFI partition Kconfig.

EFI partitions are also used by Apple on their Intel-based machines and
thus you need EFI partition support if you (for example) want to attach
such a machine in target disk mode.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NMatt Domsch <Matt_Domsch@dell.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Testing of -rt by IBM uncovered a locking bug in wake_futex_pi(): the PI
state needs to be locked before we access it.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Chuck Ebbert <cebbert@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NMarcel Selhorst <tpm@selhorst.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Initialise the SAK member of the vc_cons variable on all virtual terminals,
not only the first one.  This prevents an oops when trying Sysrq-C on e.g.
the second virtual terminal:

  kernel BUG at kernel/workqueue.c:212!
  invalid opcode: 0000 [1] SMP
  CPU 0
  Modules linked in: i915 drm deflate zlib_deflate twofish twofish_common serpent blowfish des ce
  Pid: 0, comm: swapper Not tainted 2.6.21-rc3-default #15
  RIP: 0010:[<ffffffff8028c955>]  [<ffffffff8028c955>] queue_work+0x32/0x51
  RSP: 0018:ffffffff805fada8  EFLAGS: 00010013
  RAX: ffffffff80683f38 RBX: ffffffff804ae700 RCX: 0000000000000000
  RDX: 0000000000000000 RSI: ffffffff80683f30 RDI: ffff81000134a840
  RBP: 0000000000000001 R08: 0000000000000005 R09: 0000000000000002
  R10: ffffffff805990e0 R11: ffff810037f4c0f0 R12: 000000000000006b
  R13: ffff81007aa23000 R14: 0000000000000001 R15: 0000000000000096
  FS:  0000000000000000(0000) GS:ffffffff804d8000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
  CR2: 00002b72026e9000 CR3: 0000000079175000 CR4: 00000000000006e0
  Process swapper (pid: 0, threadinfo ffffffff8059e000, task ffffffff80490840)
  Stack:  0000000000000096 ffffffff803635db ffffffff805fadf8 0000000000000001
   ffff8100013c2e40 0000000000000025 ffff81007c931c00 ffff81007aa23000
   0000000000000001 ffffffff8035e3ee 0000000000000092 ffff810037cc8000
  Call Trace:
   <IRQ>  [<ffffffff803635db>] __handle_sysrq+0x98/0x129
   [<ffffffff8035e3ee>] kbd_event+0x32e/0x56a
   [<ffffffff8037d502>] input_event+0x422/0x44a
   [<ffffffff80381d71>] atkbd_interrupt+0x449/0x503
   [<ffffffff8037a42d>] serio_interrupt+0x37/0x6f
   [<ffffffff8037affb>] i8042_interrupt+0x1f4/0x20a
   [<ffffffff8026bd20>] smp_send_timer_broadcast_ipi+0x2d/0x4e
   [<ffffffff8020eee5>] handle_IRQ_event+0x25/0x53
   [<ffffffff802a924c>] handle_edge_irq+0xe4/0x128
   [<ffffffff802562ac>] call_softirq+0x1c/0x28
   [<ffffffff802632eb>] do_IRQ+0x6c/0xd3
   [<ffffffff8024f4e7>] mwait_idle+0x0/0x45
   [<ffffffff80255631>] ret_from_intr+0x0/0xa
   <EOI>  [<ffffffff80248a4d>] datagram_poll+0x0/0xc8
   [<ffffffff8024f529>] mwait_idle+0x42/0x45
   [<ffffffff80242c05>] cpu_idle+0x8b/0xae
   [<ffffffff805a8779>] start_kernel+0x2b9/0x2c5
   [<ffffffff805a815e>] _sinittext+0x15e/0x162

  Code: 0f 0b eb fe 48 8b 07 48 63 d2 48 f7 d0 48 8b 3c d0 e8 13 ff
  RIP  [<ffffffff8028c955>] queue_work+0x32/0x51
   RSP <ffffffff805fada8>
  Kernel panic - not syncing: Aiee, killing interrupt handler!
Signed-off-by: NBernhard Walle <bwalle@suse.de>
Acked-by: NEric Biederman <ebiederm@xmission.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We need vid_which_vrm and vid_from_reg in the w83793 module.
Signed-off-by: NStefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Looks like we need a check in nfs_getattr() for a regular file. It makes
no sense to call nfs_sync_mapping_range() on anything else. I think that
should fix your problem: it will stop the NFS client from interfering
with dirty pages on that inode's mapping.
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: NOlof Johansson <olof@lixom.net>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The current NFS client congestion logic is severly broken, it marks the
backing device congested during each nfs_writepages() call but doesn't
mirror this in nfs_writepage() which makes for deadlocks.  Also it
implements its own waitqueue.

Replace this by a more regular congestion implementation that puts a cap on
the number of active writeback pages and uses the bdi congestion waitqueue.

Also always use an interruptible wait since it makes sense to be able to
SIGKILL the process even for mounts without 'intr'.
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: NTrond Myklebust <trond.myklebust@fys.uio.no>
Cc: Christoph Lameter <clameter@engr.sgi.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The only error code which comes from the partition checkers is -1, when
they finds an EIO.  As per the discussion, ENOMEM values were ignored,
as they might scare the users.

So, with the current code, we end up returning -1 and not EIO for the
ioctl() calls.  Which doesn't give any clue to the user of what went
wrong.
Signed-off-by: NSuzuki K P <suzuki@in.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When the console is in VT_AUTO+KD_GRAPHICS mode, switching to the
SUSPEND_CONSOLE fails, resulting in vt_waitactive() waiting indefinitely or
until the task is interrupted.  This patch tests if a console switch can
occur in set_console() and returns early if a console switch is not
possible.

[akpm@linux-foundation.org: cleanup]
Signed-off-by: NAndrew Johnson <ajohnson@intrinsyc.com>
Acked-by: NPavel Machek <pavel@ucw.cz>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

smbfs allocates rq_trans2buffer to handle server's multi transaction2 response
messages.  As struct smb_request may be reused, rq_trans2buffer is freed
before each new request.  However if last servers's response is not multi but
single trans2 message then new rq_trans2buffer is not allocated but last
smb_rput still tries to free it again.

To prevent this issue rq_trans2buffer pointer should be set to NULL after
kfree.
Signed-off-by: NVasily Averin <vvs@sw.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Frame buffer device drivers that cannot be built as modules must depend on
`FB = y'.  Correct the 3 remaining offenders.
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ecryptfs_d_release() first dereferences a pointer (via
ecryptfs_dentry_to_lower()) and then afterwards checks to see if the
pointer it just dereferenced is NULL (via ecryptfs_dentry_to_private()).

This patch moves all of the work done on the dereferenced pointer inside a
block governed by the condition that the pointer is non-NULL.
Signed-off-by: NMichael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

commit f4304ab2 (HZ free NTP) moved the
access to wall_to_monotonic in hrtimer_get_softirq_time() out of the
xtime_lock protection.

Move it back into the seq_lock section.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NJohn Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Prevents a potential oops with CONFIG_SPI_DEBUG given flakey hardware or
incorrect configuration.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

hrtimer_forward() does not check for the possible overflow of
timer->expires.  This can happen on 64 bit machines with large interval
values and results currently in an endless loop in the softirq because the
expiry value becomes negative and therefor the timer is expired all the
time.

Check for this condition and set the expiry value to the max.  expiry time
in the future.  The fix should be applied to stable kernel series as well.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NIngo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

SavagePrintRegs() requires struct savagefb_par.
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is a hack that seems to kick start the 2D engine of the Savage IX in some
Toshiba laptops.  Without this, the laptop starts with a black screen and
occasionally crashes X.
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pixclock setting in sstfb didn't work with my Voodoo 2 card with ICS 5342 DAC
(this DAC requires two consecutive writes to one of its registers to program
pixclock - maybe first write merged with second).
Signed-off-by: NOndrej Zajicek <santiago@crfreenet.org>
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It's been pointed out that output GPIOs should have an initial value, to
avoid signal glitching ...  among other things, it can be some time before
a driver is ready.  This patch corrects that oversight, fixing

 - documentation
 - platforms supporting the GPIO interface
 - users of that call (just one for now, others are pending)

There's only one user of this call for now since most platforms are still
using non-generic GPIO setup code, which in most cases already couples the
initial value with its "set output mode" request.

Note that most platforms are clear about the hardware letting the output
value be set before the pin direction is changed, but the s3c241x docs are
vague on that topic ...  so those chips might not avoid the glitches.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Acked-by: NMilan Svoboda <msvoboda@ra.rockwell.com>
Acked-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix a bug in the cleanup of an spi_bitbang bus.

The workqueue associated with the bus was destroyed before the call to
spi_unregister_master.  That meant that spi devices on that bus would be
unable to do IO in their remove method.  The shutdown flag should have been
able to prevent a segfault, but was never getting set.  By waiting to
destroy the workqueue until after the master is unregistered, devices are
able to do IO in their remove methods.  An added benefit is that neither
the shutdown flag nor a wait for the queue of messages to empty is needed.
Signed-off-by: NChris Lesiak <chris.lesiak@licor.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch fixes a user-triggerable oops that was reported by Leonid
Ananiev as archived at http://lkml.org/lkml/2007/2/8/337.

dio writes invalidate clean pages that intersect the written region so that
subsequent buffered reads go to disk to read the new data.  If this fails
the interface tries to tell the caller that the cache is inconsistent by
returning EIO.

Before this patch we had the problem where this invalidation failure would
clobber -EIOCBQUEUED as it made its way from fs/direct-io.c to fs/aio.c.
Both fs/aio.c and bio completion call aio_complete() and we reference freed
memory, usually oopsing.

This patch addresses this problem by invalidating before the write so that
we can cleanly return -EIO before ->direct_IO() has had a chance to return
-EIOCBQUEUED.

There is a compromise here.  During the dio write we can fault in mmap()ed
pages which intersect the written range with get_user_pages() if the user
provided them for the source buffer.  This is a crazy thing to do, but we
can make it mostly work in most cases by trying the invalidation again.
The compromise is that we won't return an error if this second invalidation
fails if it's an AIO write and we have -EIOCBQUEUED.

This was tested by having two processes race performing large O_DIRECT and
buffered ordered writes.  Within minutes ext3 would see a race between
ext3_releasepage() and jbd holding a reference on ordered data buffers and
would cause invalidation to fail, panicing the box.  The test can be found
in the 'aio_dio_bugs' test group in test.kernel.org/autotest.  After this
patch the test passes.
Signed-off-by: NZach Brown <zach.brown@oracle.com>
Signed-off-by: NBenjamin LaHaise <bcrl@kvack.org>
Cc: Leonid Ananiev <leonid.i.ananiev@linux.intel.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

madvise(MADV_REMOVE) can go into an infinite loop or cause an oops if the
call covers a region from the start of a vma, and extending past that vma.
Signed-off-by: NNick Piggin <npiggin@suse.de>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Acked-by: NHugh Dickins <hugh@veritas.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

During modification of code to support UFS2 writing, the case with
"three indirect" blocks in truncate path was missed, this patch fixes
this situation.
Signed-off-by: NEvgeniy Dushistov <dushistov@mail.ru>
Acked-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch fix behaviour in such test scenario:

  lseek(fd, BIG_OFFSET)
  write(fd, buf, sizeof(buf))
  truncate(BIG_OFFSET)
  truncate(BIG_OFFSET + sizeof(buf))
  read(fd, buf...)

Because of if file big enough(BIG_OFFSET) we start allocate space by block,
ordinary block size > page size, so we should zeroize the rest of block in
truncate(except last framgnet, about which VFS should care), to not get
garbage, when we extend file.

Also patch corrects conversion from pointer to block to physical block number,
this helps in case of not common used UFS types.

And add to debug output inode number.
Signed-off-by: NEvgeniy Dushistov <dushistov@mail.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This fixes "change blocks numbers on the fly" in case when "prepare
write page" is in the call chain, in this case some buffers may be not
uptodate and not mapped, we should care to map them and load from disk.

This patch was tested with:
 - ufs regressions simple tests
 - fsx-linux
 - ltp(20060306)
 - untar and build kernel
Signed-off-by: NEvgeniy Dushistov <dushistov@mail.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch corrects work with time in UFS2 case.

1) According to UFS2 disk layout modification/access and so on "time"
   should be hold in two variables one 64bit for seconds and another 32bit for
   nanoseconds,

   at now for some unknown reason we suppose that "inode time" holds in
   three variables 32bit for seconds, 32bit for milliseconds and 32bit for
   nanoseconds.

2) We set amount of nanoseconds in "VFS inode" to 0 during read, instead of
   getting values from "on disk inode"(this should close
   http://bugzilla.kernel.org/show_bug.cgi?id=7991).
Signed-off-by: NEvgeniy Dushistov <dushistov@mail.ru>
Cc: Bjoern Jacke <bjoern@j3e.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Prevent the WARN_ON() in arch/x86_64/kernel/acpi/sleep.c:init_low_mapping()
from triggering by disabling nonboot CPUs before we finally enter the
platform suspend.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If swsusp is using the platform mode during the resume and the image cannot
be read, the platform mode should be switched off before software_resume()
returns.  Make it happen.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>