1. new skb only need dst and ip address(v4 or v6).
2. skb_copy may need high order pages, which is very rare on long running server.
Signed-off-by: NJunwei Zhang <linggao.zjw@alibaba-inc.com>
Signed-off-by: NMartin Zhang <martinbj2008@gmail.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use PAGE_ALIGNED(...) instead of open-coding it.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rb->frames_per_block is an unsigned int, thus can never be negative.

Also fix spacing in the calculation of frames_per_block.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The NOLINK state will poll the phy once a second to see if the link
has come up. If the phy has an interrupt line, this polling can be
skipped, since the phy should interrupt when the link returns.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 88E1540 can be found embedded in the Marvell 88E6352 switch.  It
is compatible with the 88E1510, so add support for it, using the
88E1510 specific functions.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Save and restore FP/LR in BPF prog prologue and epilogue, save SP to FP
in prologue in order to get the correct stack backtrace.

However, ARM64 JIT used FP (x29) as eBPF fp register, FP is subjected to
change during function call so it may cause the BPF prog stack base address
change too.

Use x25 to replace FP as BPF stack base register (fp). Since x25 is callee
saved register, so it will keep intact during function call.
It is initialized in BPF prog prologue when BPF prog is started to run
everytime. Save and restore x25/x26 in BPF prologue and epilogue to keep
them intact for the outside of BPF. Actually, x26 is unnecessary, but SP
requires 16 bytes alignment.

So, the BPF stack layout looks like:

                                 high
         original A64_SP =>   0:+-----+ BPF prologue
                                |FP/LR|
         current A64_FP =>  -16:+-----+
                                | ... | callee saved registers
                                +-----+
                                |     | x25/x26
         BPF fp register => -80:+-----+
                                |     |
                                | ... | BPF prog stack
                                |     |
                                |     |
         current A64_SP =>      +-----+
                                |     |
                                | ... | Function call stack
                                |     |
                                +-----+
                                  low

CC: Zi Shen Lim <zlim.lnx@gmail.com>
CC: Xi Wang <xi.wang@gmail.com>
Signed-off-by: NYang Shi <yang.shi@linaro.org>
Acked-by: NZi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reset pskb in macvlan_handle_frame in case skb_share_check returned a
clone.

Fixes: 8a4eb573 ("net: introduce rx_handler results and logic around that")
Signed-off-by: NSabrina Dubroca <sd@queasysnail.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ipvlan_handle_frame is a rx_handler, and when it returns a value other
than RX_HANDLER_CONSUMED (here, NET_RX_DROP aka RX_HANDLER_ANOTHER),
__netif_receive_skb_core expects that the skb still exists and will
process it further, but we just freed it.

Fixes: 2ad7bf36 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: NSabrina Dubroca <sd@queasysnail.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass a **skb to ipvlan_rcv_frame so that if skb_share_check returns a
new skb, we actually use it during further processing.

It's safe to ignore the new skb in the ipvlan_xmit_* functions, because
they call ipvlan_rcv_frame with local == true, so that dev_forward_skb
is called and always takes ownership of the skb.

Fixes: 2ad7bf36 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: NSabrina Dubroca <sd@queasysnail.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vladislav Yasevich says:

====================
Fix issues with vlans without REORDER_HEADER

A while ago Phil Sutter brought up an issue with vlans without
REORDER_HEADER and bridges.  The problem was that if a vlan
without REORDER_HEADER was a port in the bridge, the bridge ended
up forwarding corrupted packets that still contained the vlan header.
The same issue exists for bridge mode macvlan/macvtap devices.

An additional issue with vlans without REORDER_HEADER is that stacking
them also doesn't work.  The reason here is that skb_reorder_vlan_header()
function assumes that it on ETH_HLEN bytes deep into the packet.  That
is not the case, when you a vlan without REORRDER_HEADER flag set.

This series attempts to correct these 2 issues.

1) To solve the stacked vlans problem, the patch simply use
skb->mac_len as an offset to start copying mac addresses that
is part of header reordering.

2) To fix the issue with bridge/macvlan/macvtap, the second patch
simply doesn't write the vlan header back to the packet if the
vlan device is either a bridge or a macvlan port.  This ends up
being the simplest and least performance intrussive solution.

I've considered extending patch 2 to all stacked devices (essentially
checked for the presense of rx_handler), but that feels like a broader
restriction and _may_ break existing uses.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a vlan is configured with REORDER_HEADER set to 0, the vlan
header is put back into the packet and makes it appear that
the vlan header is still there even after it's been processed.
This posses a problem for bridge and macvlan ports.  The packets
passed to those device may be forwarded and at the time of the
forward, vlan headers end up being unexpectedly present.

With the patch, we make sure that we do not put the vlan header
back (when REORDER_HEADER is 0) if a bridge or macvlan has
been configured on top of the vlan device.
Signed-off-by: NVladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we have multiple stacked vlan devices all of which have
turned off REORDER_HEADER flag, the untag operation does not
locate the ethernet addresses correctly for nested vlans.
The reason is that in case of REORDER_HEADER flag being off,
the outer vlan headers are put back and the mac_len is adjusted
to account for the presense of the header.  Then, the subsequent
untag operation, for the next level vlan, always use VLAN_ETH_HLEN
to locate the begining of the ethernet header and that ends up
being a multiple of 4 bytes short of the actuall beginning
of the mac header (the multiple depending on the how many vlan
encapsulations ethere are).

As a reslult, if there are multiple levles of vlan devices
with REODER_HEADER being off, the recevied packets end up
being dropped.

To solve this, we use skb->mac_len as the offset.  The value
is always set on receive path and starts out as a ETH_HLEN.
The value is also updated when the vlan header manupations occur
so we know it will be correct.
Signed-off-by: NVladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By default the driver allowed incorrect frames to be received. What is
worse the code does not handle very short frames correctly. The FCS
length is unconditionally subtracted, and the underflow can cause
skb_put to be called with large number after implicit cast to unsigned.
And indeed, an skb_over_panic() was observed with via-velocity.

This removes the module parameter as it does not work in it's
current state, and should be implemented via NETIF_F_RXALL if needed.
Suggested-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NTimo Teräs <timo.teras@iki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that IP1000A chips are supported by dl2k driver, the buggy ipg
driver can be removed.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for IP1000A chips to dl2k driver.
IP1000A chip looks like a TC9020 with integrated PHY.

This allows IP1000A chips to work reliably because the ipg driver is
buggy - it loses packets under load and then completely stops
transmitting data.

Tested with Asus NX1101 v2.0 at 10, 100 and 1000Mbps:
vendor=0x13f0 device=0x1023 (rev 0x41)
subsystem vendor=0x1043 device=0x8180

MAC address registers access needed to be changed from 8-bit to 16-bit
because 8-bit does not work on IP1000A. 8-bit access is not even
allowed in the TC9020 datasheet (although it worked). 16-bit access
works on both.

Tested that it does not break D-Link DGE-550T (DL-2000 chip, probably
a rebranded TC9020):
vendor=0x1186 device=0x4000 (rev 0x0c)
subsystem vendor=0x1186 device=0x4000
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

the OUTMCAST stat is double incremented, getting bumped once in the mcast code
itself, and again in the common ip output path.  Remove the mcast bump, as its
not needed

Validated by the reporter, with good results
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Reported-by: NClaus Jensen <claus.jensen@microsemi.com>
CC: Claus Jensen <claus.jensen@microsemi.com>
CC: David Miller <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In some cases the crash is caused by nicvf_remove() being called from
outside. For example, if we try to feed the device to vfio after the
probe has failed for some reason. So, move the check to better place.
Signed-off-by: NPavel Fedin <p.fedin@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A recent flaw in the netdev feature setting resulted in warnings
like this one from VLAN interfaces:

 WARNING: CPU: 1 PID: 4975 at net/core/dev.c:2419 skb_warn_bad_offload+0xbc/0xcb()
 : caps=(0x00000000001b5820, 0x00000000001b5829) len=2782 data_len=0 gso_size=1348 gso_type=16 ip_summed=3

The ":" is supposed to be preceded by a driver name, but in this
case it is an empty string since the device has no parent.

There are many types of network devices without a parent. The
anonymous warnings for these devices can be hard to debug.  Log
the network device name instead in these cases to assist further
debugging.

This is mostly similar to how __netdev_printk() handles orphan
devices.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case multiple writes to a unix stream socket race we could end up in a
situation where we pre-allocate a new skb for use in unix_stream_sendpage
but have to free it again in the locked section because another skb
has been appended meanwhile, which we must use. Accidentally we didn't
clear the pointer after consuming it and so we touched freed memory
while appending it to the sk_receive_queue. So, clear the pointer after
consuming the skb.

This bug has been found with syzkaller
(http://github.com/google/syzkaller) by Dmitry Vyukov.

Fixes: 869e7c62 ("net: af_unix: implement stream sendpage support")
Reported-by: NDmitry Vyukov <dvyukov@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rtnl_fdb_dump always expects an index to be returned by the ndo_fdb_dump op,
but when CONFIG_NET_SWITCHDEV is off, it returns an error.

Fix that by returning the given unmodified idx.

A similar fix was 0890cf6c ("switchdev: fix return value of
switchdev_port_fdb_dump in case of error") but for the CONFIG_NET_SWITCHDEV=y
case.

Fixes: 45d4122c ("switchdev: add support for fdb add/del/dump via switchdev_port_obj ops.")
Signed-off-by: NDragos Tatulea <dragos@endocode.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 05cc5a39 "bnx2x: add vlan filtering offload" introduced
a regression in regard for vlans for 57710, 57711 adapters -
Loading 8021q module on a machine with such an adapter would cause
a null pointer dereference, as the driver mistakenly publishes it
has capabilities for vlan CTAG filtering.
Reported-by: NOtto Sabart <osabart@redhat.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver does not handle the AVB-DMAC Receive FIFO Warning interrupt
now, so the interrupt should not be enabled.
Signed-off-by: NMasaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sending ICMP packets with raw sockets ends up in the SNMP counters
logging the type as the first byte of the IPv4 header rather than
the ICMP header. This is fixed by adding the IP Header Length to
the casting into a icmphdr struct.
Signed-off-by: NBen Cartwright-Cox <ben@benjojo.co.uk>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This pci_error_handlers structure is never modified, like all the other
pci_error_handlers structures, so declare it as const.

Done with the help of Coccinelle.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This pci_error_handlers structure is never modified, like all the other
pci_error_handlers structures, so declare it as const.

Done with the help of Coccinelle.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NShrikrishna Khare <skhare@vmware.com>
Reported-by: NMasao Uebayashi <uebayasi@gmail.com>
Signed-off-by: NBhavesh Davda <bhavesh@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since Dell DW5580 is a 3G modem, this patch adds the device as a
mobile broadband adapter
Signed-off-by: NDaniele Palmas <dnlplm@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If ndo_set_features fails __netdev_update_features() will return -1 but
this is wrong because it is expected to return 0 if no features were
changed (see netdev_update_features()), which will cause a netdev
notifier to be called without any actual changes. Fix this by returning
0 if ndo_set_features fails.

Fixes: 6cb6a27c ("net: Call netdev_features_change() from netdev_update_features()")
CC: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When __netdev_update_features() was updated to ensure some features are
disabled on new lower devices, an error was introduced for devices which
don't have the ndo_set_features() method set. Before we'll just set the
new features, but now we return an error and don't set them. Fix this by
returning the old behaviour and setting err to 0 when ndo_set_features
is not present.

Fixes: e7868a85 ("net/core: ensure features get disabled on new lower devs")
CC: Jarod Wilson <jarod@redhat.com>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Ido Schimmel <idosch@mellanox.com>
CC: Sander Eikelenboom <linux@eikelenboom.it>
CC: Andy Gospodarek <gospo@cumulusnetworks.com>
CC: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Reviewed-by: NJarod Wilson <jarod@redhat.com>
Tested-by: NFlorian Fainelli <f.fainelli@gmail.com>
Tested-by: NDave Young <dyoung@redhat.com>
Tested-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When NET_SWITCHDEV=n, switchdev_port_attr_set simply returns EOPNOTSUPP.
In this case we should not emit errors and warnings to the kernel log.
Reported-by: NSander Eikelenboom <linux@eikelenboom.it>
Tested-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Fixes: 0bc05d58 ("switchdev: allow caller to explicitly request
attr_set as deferred")
Fixes: 6ac311ae ("Adding switchdev ageing notification on port
bridged")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove rsstable array and its initialization from be_set_rss_hash_opts().
The array became unused after "e2557877 be2net: Support for configurable
RSS hash key". The initial RSS table is now filled and stored for later
usage during Rx queue creation.
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Acked-by: NSathya Perla <sathya.perla@avagotech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When RX/TX interrupt for Network Control queue and Best Effort queue
is issued at the same time, the interrupt mask of Network Control
queue will be reset when the mask of Best Effort queue is set.
This patch fixes this problem.
Signed-off-by: NMasaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On certain hardware after software reboot the chip may get stuck and fail
to reinitialize during reset. This can be fixed by ensuring that PHY is
reset too.

Old PHY resetting method required operational MDIO interface, therefore
the chip should have been already set up. In order to be able to function
during probe, it is changed to use PMT_CTRL register.

The problem could be observed on SMDK5410 board.
Signed-off-by: NPavel Fedin <p.fedin@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While recently going over ARM64's BPF code, I noticed that the icache
range we're flushing should start at header already and not at ctx.image.

Reason is that after b569c1c6 ("net: bpf: arm64: address randomize
and write protect JIT code"), we also want to make sure to flush the
random-sized trap in front of the start of the actual program (analogous
to x86). No operational differences from user side.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NZi Shen Lim <zlim.lnx@gmail.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During review I noticed that the icache range we're flushing should
start at header already and not at ctx.image.

Reason is that after 55309dd3 ("net: bpf: arm: address randomize
and write protect JIT code"), we also want to make sure to flush the
random-sized trap in front of the start of the actual program (analogous
to x86). No operational differences from user side.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Tested-by: NNicolas Schichan <nschichan@freebox.fr>
Cc: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 338d4f49
("arm64: kernel: Add support for Privileged Access Never") includes sysreg.h
into futex.h and uaccess.h. But, the inline assembly used by asm/sysreg.h is
incompatible with llvm so it will cause BPF samples build failure for ARM64.
Since sysreg.h is useless for BPF samples, just exclude it from Makefile via
defining __ASM_SYSREG_H.
Signed-off-by: NYang Shi <yang.shi@linaro.org>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BPF fp should point to the top of the BPF prog stack. The original
implementation made it point to the bottom incorrectly.
Move A64_SP to fp before reserve BPF prog stack space.

CC: Zi Shen Lim <zlim.lnx@gmail.com>
CC: Xi Wang <xi.wang@gmail.com>
Signed-off-by: NYang Shi <yang.shi@linaro.org>
Reviewed-by: NZi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support for the Vitesse VSC8601 PHY. Generic functions are
used for everything except interrupt handling.
Signed-off-by: NMans Rullgard <mans@mansr.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 77a99394 "phy/at8031: enable at8031 to work on interrupt mode"
added interrupt support for the 8031 PHY but left out the other two
chips supported by this driver.

This patch sets the .ack_interrupt and .config_intr functions for the
8030 and 8035 drivers as well.
Signed-off-by: NMans Rullgard <mans@mansr.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>