* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [NEIGH]: Fix IP-over-ATM and ARP interaction.
  [TG3]: ethtool always report port is TP.

* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC]: Fix warning on prom_getproperty in openprom.c
  [SPARC]: Handle UNWIND_INFO properly.
  [SPARC64]: Update defconfig.
  [SPARC]: show device name in /proc/dvma_map
  [SPARC]: Remove duplicate symbol exports

Fix race condition during destruction calls to avoid possibility of
accessing object after it has been freed.  Instead of waking up a wait
queue directly, which is susceptible to a race where the object is
freed between the reference count going to 0 and the wake_up(), use a
completion to wait in the function doing the freeing.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The ipath driver's table of PCI IDs needs a { 0, } entry at the end.
This makes all of the device aliases visible to userspace so hotplug
loads the module for all supported devices.  Without the patch,
modinfo ipath_core only shows:

    alias:          pci:v00001FC1d0000000Dsv*sd*bc*sc*i*

instead of the correct:

    alias:          pci:v00001FC1d00000010sv*sd*bc*sc*i*
    alias:          pci:v00001FC1d0000000Dsv*sd*bc*sc*i*
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Signed-off-by: NBryan O'Sullivan <bos@pathscale.com>

The classical IP over ATM code maintains its own IPv4 <-> <ATM stuff>
ARP table, using the standard neighbour-table code. The
neigh_table_init function adds this neighbour table to a linked list
of all neighbor tables which is used by the functions neigh_delete()
neigh_add() and neightbl_set(), all called by the netlink code.

Once the ATM neighbour table is added to the list, there are two
tables with family == AF_INET there, and ARP entries sent via netlink
go into the first table with matching family. This is indeterminate
and often wrong.

To see the bug, on a kernel with CLIP enabled, create a standard IPv4
ARP entry by pinging an unused address on a local subnet. Then attempt
to complete that entry by doing

ip neigh replace <ip address> lladdr <some mac address> nud reachable

Looking at the ARP tables by using 

ip neigh show

will reveal two ARP entries for the same address. One of these can be
found in /proc/net/arp, and the other in /proc/net/atm/arp.

This patch adds a new function, neigh_table_init_no_netlink() which
does everything the neigh_table_init() does, except add the table to
the netlink all-arp-tables chain. In addition neigh_table_init() has a
check that all tables on the chain have a distinct address family.
The init call in clip.c is changed to call
neigh_table_init_no_netlink().

Since ATM ARP tables are rather more complicated than can currently be
handled by the available rtattrs in the netlink protocol, no
functionality is lost by this patch, and non-ATM ARP manipulation via
netlink is rescued. A more complete solution would involve a rtattr
for ATM ARP entries and some way for the netlink code to give
neigh_add and friends more information than just address family with
which to find the correct ARP table.

[ I've changed the assertion checking in neigh_table_init() to not
  use BUG_ON() while holding neigh_tbl_lock.  Instead we remember that
  we found an existing tbl with the same family, and after dropping
  the lock we'll give a diagnostic kernel log message and a stack dump.
  -DaveM ]
Signed-off-by: NSimon Kelley <simon@thekelleys.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMartin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Even with fiber cards ethtool reports that the connected port is TP,
the patch fix this.
Signed-off-by: NKarsten Keil <kkeil@suse.de>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For sparc32 we need R_SPARC_UA32 relocation support, for
sparc64 we need the handle R_SPARC_DISP32 relocations.

Based upon reports and initial patch by Martin Habets.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/i2c-2.6:
  [PATCH] scx200_acb: Fix for the CS5535 errata
  [PATCH] scx200_acb: Fix resource name use after free
  [PATCH] scx200_acb: Fix return on init error

* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  [PATCH] USB: fix omninet driver bug
  [PATCH] USB: add ark3116 usb to serial driver
  [PATCH] usbserial: Fixes leak in serial_open() error path.
  [PATCH] usbserial: Fixes use-after-free in serial_open().
  [PATCH] USB: Emagic USB firmware loading fixes
  [PATCH] USB: add an IBM USB keyboard to the HID_QUIRK_NOGET blacklist
  [PATCH] USB: Add Sieraa Wireless 580 evdo card to airprime.c
  [PATCH] USB: ftdi_sio: add device id for ACT Solutions HomePro ZWave interface
  [PATCH] USB: ftdi_sio: Add support for HCG HF Dual ISO RFID Reader
  [PATCH] USB: ub oops in block_uevent
  [PATCH] USB: usbcore: don't check the device's power source
  [PATCH] USB: fix OHCI PM regression
  [PATCH] USB: pegasus fixes (logstorm, suspend)
  [PATCH] USBATM: fix modinfo output
  [PATCH] USBATM: change the default speedtouch iso altsetting
  [PATCH] USB: fix bug in ohci-hcd.c ohci_restart()

This reverts commit 56cf6504.

Both Erik Mouw and Andrew Vasquez independently pinpointed this commit
as causing problems, where the slab cache for a driver is never released
(most obviously causing problems when immediately re-loading that
driver, resulting in a "kmem_cache_create: duplicate cache <xyz>"
message, but it can also cause other trouble).

James Bottomley dug into it, and reports:

  "OK, here's the scoop.  The problem patch adds a get of driverfs_dev in
   add_disk(), but doesn't put it again until disk_release() (which occurs
   on final put_disk() of the gendisk).

   However, in SCSI, the driverfs_dev is the sdev_gendev.  That means
   there's a reference held on sdev_gendev  until final disk put.
   Unfortunately, we use the driver model driver_remove to trigger
   del_gendisk (which removes the gendisk from visibility and decrements
   the refcount), so we've introduced an unbreakable deadlock in the
   reference counting with this.

   I suggest simply reversing this patch at the moment.  If Russell and
   Jens can tell me what they're trying to do I'll see if there's another
   way to do it."

so hereby the patch gets reverted, waiting for a better fix.

Cc: Jens Axboe <axboe@suse.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Erik Mouw <erik@harddisk-recovery.com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

I introduced this way back in 2.6.13 when adding the port lock logic.
This device talks out through different "ports" all at the same time, so
the lock logic was wrong, preventing any data from ever being sent
properly.

Thanks a lot to Bernhard Reiter <bernhard@intevation.de> for being
patient and helping with debugging this.

Cc: Bernhard Reiter <bernhard@intevation.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Based on Simon's original driver, with some minor code cleanups and
tidying by me.

Cc: Simon Schulz <simon@auctionant.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If serial_open() fails at the port assignment or mutex_lock_interruptible()
is interrupted, the 'serial' object will never be freed.

We should call kref_put() when those errors happens.
Signed-off-by: NLuiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If the device is disconnected while serial_open() is executing and
either try_module_get() or the device specific open function fails, the
kref_put() call in the 'bailout_kref_put' label will free the memory
pointed out by 'port'.

The subsequent dereferences in the 'bailout_kref_put' label will be
invalid.

The fix is just to assure kref_put() is called after any 'port' usage.
Signed-off-by: NLuiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

It's become apparent as machines get faster that the emagic kernel firmware
loaders (based on the ezusb loader) have a reset race.  a 400MHz TiBook
never tripped it, but a 2GHz Pentium M seems to hit it about 30% of the
time.  The bug is seen as a hung USB box and the kernel error:

drivers/usb/misc/emi62.c: emi62_load_firmware - error loading firmware:
error = -110

The patch below inserts a delay after deasserting reset to allow the box to
settle before a new command is issued.  This affects only device startup.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

After recent changes, the USB keyboard as shipped with IBM pSeries systems
does not work anymore, unless the keyboard is replugged after reboot.
Adding this model to the blacklist fixes it.
Signed-off-by: NOlaf Hering <olh@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds the Sierra Wireless card to airprime.c.

I tested this on my laptop.
Signed-off-by: NKen Brush <ken@cgi101.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 3508/1: Update collie defconfig
  [ARM] Fix thread struct allocator for SMP case
  [ARM] Update mach-types
  [ARM] Update versatile_defconfig

* master.kernel.org:/home/rmk/linux-2.6-serial:
  [SERIAL] 8250: add locking to console write function
  [SERIAL] Remove unconditional enable of TX irq for console
  [SERIAL] 8250: set divisor register correctly for AMD Alchemy SoC uart
  [SERIAL] AMD Alchemy UART: claim memory range
  [SERIAL] Clean up serial locking when obtaining a reference to a port

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [NET_SCHED]: HFSC: fix thinko in hfsc_adjust_levels()
  [IPV6]: skb leakage in inet6_csk_xmit
  [BRIDGE]: Do sysfs registration inside rtnl.
  [NET]: Do sysfs registration as part of register_netdevice.
  [TG3]: Fix possible NULL deref in tg3_run_loopback().
  [NET] linkwatch: Handle jiffies wrap-around
  [IRDA]: Switching to a workqueue for the SIR work
  [IRDA]: smsc-ircc: Minimal hotplug support.
  [IRDA]: Removing unused EXPORT_SYMBOLs
  [IRDA]: New maintainer.
  [NET]: Make netdev_chain a raw notifier.
  [IPV4]: ip_options_fragment() has no effect on fragmentation
  [NET]: Add missing operstates documentation.

* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (25 commits)
  [SCSI] mptfc: race between mptfc_register_dev and mptfc_target_alloc
  [SCSI] lpfc 8.1.6 : Fix Data Corruption in Bus Reset Path
  [SCSI] mptspi: revalidate negotiation parameters after host reset and resume
  [SCSI] srp.h: avoid padding of structs
  [SCSI] ibmvscsi: fix leak when failing to send srp event
  [SCSI] qla2xxx: Correct eh_abort recovery logic.
  [SCSI] megaraid_{mm,mbox}: fix a bug in reset handler
  [SCSI] fusion - bug fix stack overflow in mptbase
  [SCSI] scsi: Add IBM 2104-DU3 to blist
  [SCSI] Fix DVD burning issues.
  [SCSI] SCSI: aic7xxx_osm_pci resource leak fix.
  [SCSI] - fusion - mptfc bug fix's to prevent deadlock situations
  [SCSI] mptfusion: bug fix's for raid components adding/deleting
  [SCSI] aic7xxx: ahc_pci_write_config() fix
  [SCSI] megaraid: unused variable
  [SCSI] qla2xxx: only free_irq() after request_irq() succeeds
  [SCSI] Overrun in drivers/scsi/sim710.c
  [SCSI] lpfc 8.1.5 : Change version number to 8.1.5
  [SCSI] lpfc 8.1.5 : Misc small fixes
  [SCSI] lpfc 8.1.5 : Additional fixes to LOGO, PLOGI, and RSCN processing
  ...

Don't recurse back into the driver even if the unplug threshold is met,
when the driver asks for a requeue. This is both silly from a logical
point of view (requeues typically happen due to driver/hardware
shortage), and also dangerous since we could hit an endless request_fn
-> requeue -> unplug -> request_fn loop and crash on stack overrun.

Also limit blk_run_queue() to one level of recursion, similar to how
blk_start_queue() works.

This patch fixed a real problem with SLES10 and lpfc, and it could hit
any SCSI lld that returns non-zero from it's ->queuecommand() handler.
Signed-off-by: NJens Axboe <axboe@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

When deleting the last child the level of a class should drop to zero.

Noticed by Andreas Mueller <andreas@stapelspeicher.org>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eric Biederman points out that we can't take the task_lock while holding
tasklist_lock for writing, because another CPU that holds the task lock
might take an interrupt that then tries to take tasklist_lock for writing.

Which would be a nasty deadlock, with one CPU spinning forever in an
interrupt handler (although admittedly you need to really work at
triggering it ;)

Since the ptrace_attach() code is special and very unusual, just make it
be extra careful, and use trylock+repeat to avoid the possible deadlock.

Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/mthca: FMR ioremap fix
  IPoIB: Free child interfaces properly
  IB/mthca: Fix race in reference counting
  IB/srp: Fix tracking of pending requests during error handling
  IB: Fix display of 4-bit port counters in sysfs

Addresses for ioremap must be calculated off of pci_resource_start;
we can't directly use the bus address as seen by the HCA.  Fix the
code that remaps device memory for FMR access.

Based on patch by Klaus Smolin.
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

* 'upstream' of master.kernel.org:/pub/scm/linux/kernel/git/shemminger/netdev-2.6:
  sis900: phy for FoxCon motherboard
  dl2k: use DMA_48BIT_MASK constant
  phy: mdiobus_register(): initialize all phy_map entries
  sky2: ifdown kills irq mask

661FX7MI-S motherboard which uses the SiS 661FX chipset.  The patch adds
an entry to mii_chip_info for the transceiver.

The PHY ids were found using the sis900_c_122.diff patch from
http://brownhat.org/sis900.html but that patch didn't solve the problem,
because the PHY at address 1 was already being chosen.

Without my patch, when bursts of packets arrive from other hosts on a
LAN, the interface dropped one roughly 10% of the time, causing
retransmits.  There were fifth second pauses in refresh of large xterms,
and it made Netrek suck.  I can provide further test data.

Workaround in lieu of patch is to use mii-tool to advertise
100baseTx-HD, then force renegotiation.

I wasn't able to identify the actual transceiver, so the description
field is a guess.

This patch is similar to Artur Skawina's patch:
http://marc.theaimsgroup.com/?l=linux-netdev&m=114297516729079&w=2

I'm not sure, but I wonder if it means the default behaviour should be
changed, so as to better handle future transceivers.

Diff is against 2.6.16.13.
Signed-off-by: NJames Cameron <james.cameron@hp.com>
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Typo will be harder with this one.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

make sure phy_map entries whose PHY address is masked are initialized
to NULL, given that other code (such as mdiobus_unregister for
instance) assumes that non-NULL phy_map entries are allocated
phy_devices
Signed-off-by: NHerbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Bringing down a port also masks off the status and other IRQ's
needed for device to function due to missing paren's.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

This patch corrects the order of the calls to register_chrdev() and
pcmcia_register_driver().  Now udev correctly creates userspace device
files /dev/cmmN and /dev/cmxN respectively.

Based on an earlier patch by Jan Niehusmann <jan@gondor.com>.
Signed-off-by: NHarald Welte <laforge@netfilter.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

inet6_csk_xit does not free skb when routing fails.
Signed-off-by: NAlexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that netdevice sysfs registration is done as part of
register_netdevice; bridge code no longer has to be tricky when adding
it's kobjects to bridges.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The last step of netdevice registration was being done by a delayed
call, but because it was delayed, it was impossible to return any error
code if the class_device registration failed.

Side effects:
 * one state in registration process is unnecessary.
 * register_netdevice can sleep inside class_device registration/hotplug
 * code in netdev_run_todo only does unregistration so it is simpler.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A race condition exists in mptfc between the thread registering a device
with the fc transport and the scan work generated by the transport.
This race existed prior to the application of the mptfc bug fix patch.

mptfc_register_dev() calls fc_remote_port_add() with the FC_RPORT_ROLE_TARGET
bit set in the rport ids passed to the function.  Having this bit set causes
fc_remote_port_add() to schedule a scan of the device.

This scan can execute before mptfc_register_dev() can fill in the dd_data
in the rport structure.  When this happens, mptfc_target_alloc() will fail
because dd_data is null.

Attached is a patch which fixes the problem.  The patch changes the rport ids
passed to fc_remote_port_add() to not have the TARGET bit set.  This prevents
the scan from being scheduled.  After mptfc_register_dev() fills in the rport
dd_data field, fc_remote_port_rolechg() is called, changing the role of the
rport to TARGET.  Thus, the scan is scheduled after dd_data is filled
in which prevents the failure in mptfc_target_alloc().
Signed-off-by: NMichael Reed <mdr@sgi.com>
Signed-off-by: NEric Moore <Eric.Moore@lsil.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

tg3_run_loopback doesn't check that dev_alloc_skb() returns anything
useful.

Even if dev_alloc_skb() fails to return an skb to us we'll happily go
on and assume it did, so we risk dereferencing a NULL pointer.  Much
better to fail gracefully by returning -ENOMEM than crashing here.
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When deleting a child interface with a non-default P_Key via
/sys/class/net/ibX/delete_child, the interface must be freed with
free_netdev() (rather than kfree() on the private data).
Signed-off-by: NRoland Dreier <rolandd@cisco.com>