Thanks to Terry Wu for finding the GPIOs required for svideo / composite input

Cc: Terry Wu <terrywu2009@gmail.com>
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Enable the standby mode optimization to disable the tda18271
slave tuner output / loop thru options when in low power mode
on the slave tuner, only.  The master tuner must always leave
slave tuner output / loop thru enabled.
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

- set correct colors at startup time
- autogain was too slow (4-5 mn - now 15-30 s))
Signed-off-by: NAmauri Magagna <amaurimagagna@gmail.com>
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

- add flip/mirror support for OV2640
- fix for backlight value range
- fix for red-blue inversion hue mode with V4L1 applications
Signed-off-by: NOlivier Lorin <o.lorin@laposte.net>
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

- small changes in comments
- unified naming scheme for subdriver variables
Signed-off-by: NOlivier Lorin <o.lorin@laposte.net>
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

- fix for warning compilation about sd_ctrls
- trace improvement while probing the sensor
Signed-off-by: NOlivier Lorin <o.lorin@laposte.net>
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The original implementation of pac_find_sof() does not always find
the Start Of Frame (SOF) marker. Replace it with a state machine
based design.
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMarton Nemeth <nm127@freemail.hu>
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Xc5000 tuning attempts shouldn't return zero in the case where the firmware
did not load successfully.

Thanks to Michael Krufky for pointing out this issue.

Cc: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add support for saturation/hue controls, prompted by errors showing up in
the mythbackend log.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

gspca: Don't resubmit error status URB's when suspending
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The gscpa core was not resubmitting URB's when the URB status was an error,
this means we will loose URB's (potentially all stopping the stream) in
case of sporadic USB issues. I've seen this with an Aiptek stv0680 based
PenCam connected through an USB 2.0 hub.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds a new subdriver to gspca supporting cams with the stv0680
bridge (replacing the old in kernel v4l1 driver).

Many thanks to Hans Verkuil for providing me with one of the 2 cams used in
testing this new sub driver.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

gspca w9968cf: slight tweak to vstart and hstart to get rid of black borders
in 640x480 mode.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

gspca w9968cf: Add support for JPEG compression, this enables much higher
framerates at 320x240 / 352x288 and also allows for 640x480 mode for
cams which can do this. The w9968cf uses planar JPEG, which libv4l until
now did not support, so this requires atleast version 0.6.3 of libv4l.

And something important I forgot to mention in my earlier w9968cf commits:
Many thanks to Hans Verkuil for giving me a w9968cf based cam, which has
allowed me to develop the gspca w9968cf support.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

gspca-w9968cf: Don't add an extra packet to the buffer after the EOF,
this makes the frame data size bigger then it should be which makes
gstreamer discard it.

This patch also fixes an unrelated compiler warning.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Cache sensor regs to avoid unnecessary slow i2c reads / writes, this speeds
up sd_start a bit with most bridges and a lot (from 5 seconds down to 0.3
seconds) with W996xCF cams, as this avoids very slow bit bang IO over
USB i2c reads.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds support to gspca for the Winbond W9967CF and W9968CF
camera's. This is mostly a port of the existing v4l1 driver to gspca
(making it v4l2). But this also features fixes to the bitbanging i2c code
(send a nack not an ack after reading the last byte of a transfer), which
gets rid of the weird errors which were being seen there, and of
the smbus_refresh() hack to get around these errors.

Also the vstart settings have been tweaked to work with different
frequency filter settings.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds support for TEF6862 Car Radio Enhanced Selectivity Tuner.

It's implemented as a subdev, supporting checking signal strength
and setting and getting frequency.
Signed-off-by: NRichard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If the I2C device provides an interrupt it is registered and the
standard
is updated via interrupts rather than polling.

Since I2C communication is needed, the interrupt handler fires off a
work which will check the new standard, and store it in the internal
structure.

To handle mutual exclusion a mutex is introduced.
Signed-off-by: NRichard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch defines the probe and remove function as __devinit and __devexit.
Signed-off-by: NRichard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Support for settings the input standard of the ADV7180.

When the input standard is set there is no use to ask the
chip for standard, therefore it is cached in the driver.
Signed-off-by: NRichard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds support to the ADV7180 driver to check the input
status.

Since the status is held in the same register as the input standard
a small restructuring of the code is done to reuse the code for
reading the register
Signed-off-by: NRichard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (13168): Add support for Asus Europa Hybrid DVB-T card (SAA7134 SubVendor ID: 0x1043 Device ID: 0x4847)

Adds the device IDs and driver linking to allow the Asus Europa DVB-T
card to operate with these drivers.
The device has a SAA7134 chipset with a TD1316 Hybrid Tuner.
All inputs work on the card including switching between DVB-T and
Analogue TV, there is also no IR with this card.

[mchehab@redhat.com: CodingStyle fixes]
Signed-off-by: NDanny Wood <danwood76@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The definition of tvaudio_tuner_ops initializes the s_tuner field twice.
It appears that the second case should initialize the g_tuner field.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r@
identifier I, s, fld;
position p0,p;
expression E;
@@

struct I s =@p0 { ... .fld@p = E, ...};

@s@
identifier I, s, r.fld;
position r.p0,p;
expression E;
@@

struct I s =@p0 { ... .fld@p = E, ...};

@script:python@
p0 << r.p0;
fld << r.fld;
ps << s.p;
pr << r.p;
@@

if int(ps[0].line)!=int(pr[0].line) or int(ps[0].column)!=int(pr[0].column):
  cocci.print_main(fld,p0)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When the image size (bytesperline*height) is not multiple
of PAGE_SIZE, v4l2 rounded the required buffer size to
be multiple of PAGE_SIZE. This prevented user space
to store images directly into userptr buffers which were
not multiple of PAGE_SIZE. This constraint is removed.

The start address is still assumed to be required
page-aligned, ie., when v4l2 allocates mmap buffers,
the offset between different buffers is page-aligned.
Signed-off-by: NTuukka Toivonen <tuukka.o.toivonen@nokia.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

DVBS2API introduced two new ioctls that allows changing/getting details about newer
video standards like DVB-S2 and ISDB-T. There are lots of thing to do in this chapter,
but, for now, just add a session there, in order to allow make to not complain about
undefined symbol.

With this patch, all ioctls at the frontend.h API were somehow documented.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

We'll need to add the documentation for FE_[GET|SET]_PROPERTY that
is not specific to isdb-t. Instead of doing it at frontend.xml,
it is better to have a separate session for it. Also, isdbt.xml assumes
that those ioctls were already introduced, and documents several exisiting
properties. So, better to just rename it and add the documentation for it,
together with each existing property there.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

While this ioctl should not be used, and is a good canditate for
Documentation/feature-removal-schedule.txt, while it is on kernel,
it needs to be documented.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Adds linux/dvb/frontend.h header file at DocBook, and creates cross-references
for the frontend ioctls.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Rename all sessions id's for frontend ioctls to match ioctl name and
add the proper cross-link references for those ioctls.

This also helps to identify what ioctls are missing specs.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The default streaming control timeout was found by Ondrej Zary to be too low
for some Logitech webcams. With kernel 2.6.22 and newer they would timeout
during initialization unles the audio function was initialized before the
video function.

Add a module parameter to set the streaming control timeout and increase the
default value from 1000ms to 3000ms to fix the above problem.

Thanks to Ondrej Zary for investigating the issue and providing an initial
patch.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

At least one 5986:0241 webcam model includes vendor-specific descriptors
at the end of its streaming interface descriptors. Print an information
UVC_TRACE_DESCR message and try to continue parsing the descriptors
rather than bailing out with an error.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch sets stream->urb_size as psize*npackets
before calling uvc_alloc_urb_buffers, which may fix
a possible failure of usb_buffer_free in case usb_buffer_alloc
returns NULL. The patch is based on the ideas below:

1,If usb_buffer_alloc can't allocate a buffer sucessfully,
uvc_free_urb_buffers will be called to free the allocated
buffers, and stream->urb_size is required to be passed to
usb_buffer_free;

2,uvc_free_urb_buffers can reset stream->urb_size.

This patch is against linux-v2.6.31-next-20090926.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The uvcvideo driver has a driver-wide lock and a reference count to protect
against a disconnect/open race. Now that videodev handles the race itself,
reference-counting in the driver can be removed.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Dismiss privileges on the file handle when calling VIDIOC_REQBUFS with a
buffer count of 0. This allows applications to release the streaming
permissions on the file handle without closing it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The VIDIOC_TRY_FMT ioctl doesn't interfere with video streaming and thus
should succeed on an unprivileged file handle.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>