提交 · 180a2c542ce904e256ba0d8732517d7f42b3f3fa · openanolis / cloud-kernel

11 3月, 2016 1 次提交

Bluetooth: btusb: Add a new AR3012 ID 13d3:3472 · 75c6aca4

由 Dmitry Tunin 提交于 3月 04, 2016

T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3472 Rev=00.01
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

BugLink: https://bugs.launchpad.net/bugs/1552925Signed-off-by: NDmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

75c6aca4

29 2月, 2016 1 次提交

Bluetooth: btusb: Add a new AR3012 ID 04ca:3014 · 81d90442

由 Dmitry Tunin 提交于 2月 28, 2016

T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=03 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=04ca ProdID=3014 Rev=00.02
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

BugLink: https://bugs.launchpad.net/bugs/1546694Signed-off-by: NDmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

81d90442

24 2月, 2016 2 次提交

Bluetooth: Add new AR3012 ID 0489:e095 · 28c971d8

由 Dmitry Tunin 提交于 2月 10, 2016

T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e095 Rev=00.01
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

This device requires ar3k/AthrBT_0x31010100.dfu and
ar3k/ramps_0x31010100_40.dfu firmware files that are not in
linux-firmware yet.

BugLink: https://bugs.launchpad.net/bugs/1542944Signed-off-by: NDmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

28c971d8

Bluetooth: btusb: Add new AR3012 ID 13d3:3395 · 609574eb

由 Dmitry Tunin 提交于 2月 10, 2016

T: Bus=03 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3395 Rev=00.01
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

BugLink: https://bugs.launchpad.net/bugs/1542564Reported-and-tested-by: NChristopher Simerly <kilikopela29@gmail.com>
Signed-off-by: NDmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

609574eb

10 12月, 2015 3 次提交

Bluetooth: btintel: Create common Intel Version Read function · 6c483de1

由 Loic Poulain 提交于 12月 06, 2015

The Intel Version Read command is used to retrieve information
about hardware and firmware version/revision of Intel Bluetooth
controllers. This is an Intel generic command used in USB and
UART drivers.
Signed-off-by: NLoic Poulain <loic.poulain@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

6c483de1

Bluetooth: btintel: Add manufacturing enter/exit helpers · 28dc4b92

由 Loic Poulain 提交于 12月 03, 2015

Older Intel controllers need to enter manufacturing mode to perform
some vendor specific operations (patching, configuration...).
Add enter/exit manufaturing methods and refactor existing
manufacturing code.
Exit can be configured to perform a reset. Reset can be performed
either with patches activated or deactivated.
Signed-off-by: NLoic Poulain <loic.poulain@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

28dc4b92

Bluetooth: Add support of Toshiba Broadcom based devices · 1623d0bf

由 Dmitry Tunin 提交于 12月 05, 2015

BugLink: https://bugs.launchpad.net/bugs/1522949

    T: Bus=03 Lev=02 Prnt=02 Port=05 Cnt=02 Dev#= 4 Spd=12 MxCh= 0
    D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
    P: Vendor=0930 ProdID=0225 Rev=01.12
    S: Manufacturer=Broadcom Corp
    S: Product=BCM43142A0
    S: SerialNumber=4CBB58034671
    C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
    I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
    I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
    I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
    I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: NDmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

1623d0bf

20 11月, 2015 1 次提交

Bluetooth: Use new hci_skb_pkt_* wrappers for drivers · 618e8bc2

由 Marcel Holtmann 提交于 11月 05, 2015

The new hci_skb_pkt_* wrappers are mainly intented for drivers to
require less knowledge about bt_cb(sbk) handling. So after converting
the core packet handling, convert all drivers.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

618e8bc2

05 11月, 2015 1 次提交

Bluetooth: Fix possible deadlock in btusb · f6fc86f2

由 Kuba Pawlak 提交于 10月 28, 2015

commit 8f9d02f4 introduced spinlocks
in btusb_work. This is run in a context of a worqueue and can be interrupted
by hardware irq. If it happens while spinlock is held, we have a deadlock.
Solution is to use _irqsave/_resore version of locking

[  466.460560] =================================
[  466.460565] [ INFO: inconsistent lock state ]
[  466.460572] 4.3.0-rc6+ #1 Tainted: G        W
[  466.460576] ---------------------------------
[  466.460582] inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
[  466.460589] kworker/0:2/94 [HC0[0]:SC0[0]:HE1:SE1] takes:
[  466.460595]  (&(&data->rxlock)->rlock){?.-...}, at: [<ffffffffa0526923>] btusb_work+0xa3/0x3fd [btusb]
[  466.460621] {IN-HARDIRQ-W} state was registered at:
[  466.460625]   [<ffffffff811021b5>] __lock_acquire+0xc45/0x1e80
[  466.460638]   [<ffffffff811040d5>] lock_acquire+0xe5/0x1f0
[  466.460646]   [<ffffffff8182f108>] _raw_spin_lock+0x38/0x50
[  466.460657]   [<ffffffffa0525448>] btusb_recv_intr+0x38/0x170 [btusb]
[  466.460668]   [<ffffffffa0525626>] btusb_intr_complete+0xa6/0x130 [btusb]
[  466.460679]   [<ffffffff815d8f1e>] __usb_hcd_giveback_urb+0x8e/0x160
[  466.460690]   [<ffffffff815d911f>] usb_hcd_giveback_urb+0x3f/0x120
[  466.460698]   [<ffffffff81606e4d>] uhci_giveback_urb+0xad/0x280
[  466.460706]   [<ffffffff81608f64>] uhci_scan_schedule.part.33+0x6b4/0xbe0
[  466.460714]   [<ffffffff81609b50>] uhci_irq+0xd0/0x180
[  466.460722]   [<ffffffff815d8296>] usb_hcd_irq+0x26/0x40
[  466.460729]   [<ffffffff81117d40>] handle_irq_event_percpu+0x40/0x300
[  466.460739]   [<ffffffff81118040>] handle_irq_event+0x40/0x60
[  466.460746]   [<ffffffff8111af39>] handle_fasteoi_irq+0x89/0x150
[  466.460754]   [<ffffffff8101e0f3>] handle_irq+0x73/0x120
[  466.460763]   [<ffffffff81832f11>] do_IRQ+0x61/0x120
[  466.460772]   [<ffffffff8183084c>] ret_from_intr+0x0/0x31
[  466.460780]   [<ffffffff81697a77>] cpuidle_enter+0x17/0x20
[  466.460790]   [<ffffffff810f62c2>] call_cpuidle+0x32/0x60
[  466.460800]   [<ffffffff810f65a8>] cpu_startup_entry+0x2b8/0x3f0
[  466.460807]   [<ffffffff818214ca>] rest_init+0x13a/0x140
[  466.460817]   [<ffffffff81f76029>] start_kernel+0x4a3/0x4c4
[  466.460827]   [<ffffffff81f75339>] x86_64_start_reservations+0x2a/0x2c
[  466.460837]   [<ffffffff81f75485>] x86_64_start_kernel+0x14a/0x16d
[  466.460846] irq event stamp: 754913
[  466.460851] hardirqs last  enabled at (754913): [<ffffffff8182f4cc>] _raw_spin_unlock_irq+0x2c/0x40
[  466.460861] hardirqs last disabled at (754912): [<ffffffff8182f28d>] _raw_spin_lock_irq+0x1d/0x60
[  466.460869] softirqs last  enabled at (753024): [<ffffffff810aeaa0>] __do_softirq+0x380/0x490
[  466.460880] softirqs last disabled at (753009): [<ffffffff810aedef>] irq_exit+0x10f/0x120
[  466.460888]
               other info that might help us debug this:
[  466.460894]  Possible unsafe locking scenario:

[  466.460899]        CPU0
[  466.460903]        ----
[  466.460907]   lock(&(&data->rxlock)->rlock);
[  466.460915]   <Interrupt>
[  466.460918]     lock(&(&data->rxlock)->rlock);
[  466.460926]
                *** DEADLOCK ***

[  466.460935] 2 locks held by kworker/0:2/94:
[  466.460939]  #0:  ("events"){.+.+.+}, at: [<ffffffff810c69bb>] process_one_work+0x16b/0x660
[  466.460958]  #1:  ((&data->work)){+.+...}, at: [<ffffffff810c69bb>] process_one_work+0x16b/0x660
[  466.460974]
Signed-off-by: NKuba Pawlak <kubax.t.pawlak@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

f6fc86f2

21 10月, 2015 13 次提交

Bluetooth: btintel: Enable extra Intel vendor events · 213445b2

由 Marcel Holtmann 提交于 10月 21, 2015

The Intel Bluetooth controllers can emit extra vendor specific events in
error conditions or for debugging purposes. To make the life easier for
engineers, enable them by default. When the vendor_diag options has been
enabled, then additional debug events are also enabled.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

213445b2

Bluetooth: btusb: Set manufacturer for Intel bootloader devices · e4c534bb

由 Marcel Holtmann 提交于 10月 21, 2015

For Intel bootloader devices, set the manufacturer information so that
it becomes possible to decode the boot process.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

e4c534bb

Bluetooth: btusb: Add support for latest Apple controllers · 22f8e9db

由 Marcel Holtmann 提交于 10月 20, 2015

The latest Apple Bluetooth controllers with Broadcom chip in it have
a small design change. Instead of including a USB hub with mouse and
keyboard devices, they are now HID interfaces on the same device.

T:  Bus=04 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 39 Spd=12   MxCh= 0
D:  Ver= 2.01 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=05ac ProdID=8290 Rev= 0.79
S:  Manufacturer=Broadcom Corp.
S:  Product=Bluetooth USB Host Controller
C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=  0mA
A:  FirstIf#= 2 IfCount= 4 Cls=ff(vend.) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=01 Prot=01 Driver=usbhid
E:  Ad=85(I) Atr=03(Int.) MxPS=   8 Ivl=10ms
I:* If#= 1 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=01 Prot=02 Driver=usbhid
E:  Ad=86(I) Atr=03(Int.) MxPS=   8 Ivl=10ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 3 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 3 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 3 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 3 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 3 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=btusb
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

The general layout of Bluetooth devices is that interface 0 is the main
interface and interface 1 is for audio data. This design obviously moves
it to main interface 2 and audio data on interface 3.

Starting with the MacBookPro12,1 (early 2015 models) the new Broadcom
BCM943602CS cards are used which show this interface layout.

usb 4-1.5: New USB device found, idVendor=05ac, idProduct=8290
usb 4-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 4-1.5: Product: Bluetooth USB Host Controller
usb 4-1.5: Manufacturer: Broadcom Corp.
Bluetooth: hci0: BCM: chip id 102 build 0243
Bluetooth: hci0: BCM: product 05ac:8290
Bluetooth: hci0: BCM20703A1 Generic USB UHE Apple 20Mhz fcbga_X87
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

22f8e9db

Bluetooth: btusb: Set early vendor info for Intel and Broadcom · 49a5f782

由 Marcel Holtmann 提交于 10月 20, 2015

For the controllers from Intel and Broadcom (including Apple), it is
helpful to have the information about the manufacturer send out early.

This patch sets the hdev->manufacturer information which will be send
out before actually calling the vendor specific hdev->setup driver
callback.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

49a5f782

Bluetooth: ath3k: Add support of AR3012 0cf3:817b device · 18e0afab

由 Dmitry Tunin 提交于 10月 16, 2015

T: Bus=04 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=817b Rev=00.02
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

BugLink: https://bugs.launchpad.net/bugs/1506615Signed-off-by: NDmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

18e0afab

Bluetooth: ath3k: Add new AR3012 0930:021c id · cd355ff0

由 Dmitry Tunin 提交于 10月 05, 2015

This adapter works with the existing linux-firmware.

T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0930 ProdID=021c Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

BugLink: https://bugs.launchpad.net/bugs/1502781Signed-off-by: NDmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

cd355ff0

Bluetooth: btusb: Add support for Foxconn/Lenovo BCM43142A0 (105b:e065) · 2faf71ce

由 Santtu Rekilä 提交于 10月 05, 2015

Recently salvaged this 'BCM43142A0' WiFi/Bluetooth module from a Lenovo laptop
and noticed it doesn't work automatically, because the USB IDs are missing
from btusb.c.

Plugging in the adapter on Linux 4.1 (dmesg):
usb 3-3.3.3: new full-speed USB device number 90 using xhci_hcd
usb 3-3.3.3: New USB device found, idVendor=105b, idProduct=e065
usb 3-3.3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-3.3.3: Product: BCM43142A0
usb 3-3.3.3: Manufacturer: Broadcom Corp
usb 3-3.3.3: SerialNumber: 0090A286559E

/sys/kernel/debug/usb/devices:
T:  Bus=03 Lev=03 Prnt=22 Port=02 Cnt=02 Dev#= 90 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=105b ProdID=e065 Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM43142A0
S:  SerialNumber=0090A286559E
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Support for the chipset was added in commit 88f9b65d and a similar BCM43142
based device was added in commit 8f0c304c.

To work around the issue, I got the firmware
(BCM43142A0_001.001.011.0122.0153) off a Windows installation of Broadcom
bluetooth driver and converted it to a .hcd -file via. hex2hcd and placed it
in /lib/firmware/brcm/BCM.hcd. After that:

$ echo "105b e065 0 19ff 0239" > /sys/bus/usb/drivers/btusb/new_id
...(plug in the adapter)
usb 3-3.3.3: new full-speed USB device number 91 using xhci_hcd
usb 3-3.3.3: New USB device found, idVendor=105b, idProduct=e065
usb 3-3.3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-3.3.3: Product: BCM43142A0
usb 3-3.3.3: Manufacturer: Broadcom Corp
usb 3-3.3.3: SerialNumber: 0090A286559E
Bluetooth: hci0: BCM: chip id 70
Bluetooth: hci0: BCM (001.001.011) build 0000
bluetooth hci0: firmware: direct-loading firmware brcm/BCM.hcd
Bluetooth: hci0: BCM (001.001.011) build 0154

Bam, now it works for me!

/sys/kernel/debug/usb/devices:
T:  Bus=03 Lev=03 Prnt=22 Port=02 Cnt=02 Dev#= 92 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=105b ProdID=e065 Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM43142A0
S:  SerialNumber=0090A286559E
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: NSanttu Rekilä <sare@r00t3d.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

2faf71ce

Bluetooth: btusb: Mark BCM2045 devices to have broken link key commands · 6c9d435d

由 Marcel Holtmann 提交于 10月 17, 2015

The BCM2045 seems to have a problem with the stored link key commands
and thus just mark them as broken.

  HCI Event: Command Complete (0x0e) plen 12
     Read Local Supported Features (0x04|0x0003) ncmd 1
     status 0x00
     Features: 0xff 0xff 0x8d 0xfe 0x8f 0xf9 0x00 0x80
  HCI Event: Command Complete (0x0e) plen 12
     Read Local Version Information (0x04|0x0001) ncmd 1
     status 0x00
     HCI Version: 2.0 (0x3) HCI Revision: 0x2000
     LMP Version: 2.0 (0x3) LMP Subversion: 0x410d
     Manufacturer: Broadcom Corporation (15)
  HCI Event: Command Complete (0x0e) plen 11
     Read Buffer Size (0x04|0x0005) ncmd 1
     status 0x00
     ACL MTU 1017:8 SCO MTU 64:0
  HCI Event: Command Complete (0x0e) plen 68
     Read Local Supported Commands (0x04|0x0002) ncmd 1
     status 0x00
     Commands: ffffff03feffcfffffffffff0300f8ff07
  HCI Event: Command Complete (0x0e) plen 4
     Delete Stored Link Key (0x03|0x0012) ncmd 1
     status 0x11 deleted 2048
     Error: Unsupported Feature or Parameter Value

From the looks of it, this device seems genuine and not one of the
devices that are neither Broadcom nor CSR devices in reality.

T: Bus=04 Lev=02 Prnt=02 Port=02 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=2045 Rev= 1.12
S: Manufacturer=Broadcom Corp
S: Product=BCM2045A
S: SerialNumber=000000000000
C:* #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=00 Driver=(none)
Reported-and-tested-by: NJulio González Mejías <juliolokooo@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

6c9d435d

Bluetooth: btintel: Add diagnostic support for older controllers · 3e24767b

由 Marcel Holtmann 提交于 10月 17, 2015

For the older controllers like Wilkens Peak and Stone Peak, enabling the
traces requires to switch into manufacturer mode first. This patch does
exactly that, but only for these older controllers.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

3e24767b

Bluetooth: btintel: Set quirk for non-persistent diagnostic settings · d8270fbb

由 Marcel Holtmann 提交于 10月 17, 2015

For Intel controllers the diagnostics settings are not persistent over
HCI Reset. So set the quirk to programm them again on every power up.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

d8270fbb

Bluetooth: btusb: Print information of Intel SfP lock states · 2220994e

由 Marcel Holtmann 提交于 10月 13, 2015

The lock states from Intel SfP controllers can only be read once before
loading the firmware. So for debugging purposes, print them out.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

2220994e

Bluetooth: btintel: Add support for enabling tracing functionality · 6d2e50d2

由 Marcel Holtmann 提交于 10月 09, 2015

For Intel controllers with firmware that allows tracing of baseband
functionality this allows enabling it via set_diag driver callback.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

6d2e50d2

Bluetooth: btusb: Add support for Broadcom LM_DIAG interface · 9d08f504

由 Marcel Holtmann 提交于 10月 08, 2015

The Broadcom Bluetooth USB devices have a third interface that is
dedicated for LM_DIAG messages. The If#= 2 describes this interface
and it consists of one bulk in and one bulk endpoint.

T:  Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 38 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=19ff ProdID=0239 Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=btusb
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

For all Broadcom based devices with this interface, the driver now
claims it and schedules URBs for it. This allows to capture the
LM_DIAG messages and allows forwarding them via hci_recv_diag into
the diagnostic channel of the Bluetooth subsystem.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

9d08f504

05 10月, 2015 2 次提交

Bluetooth: Move handling of HCI_RUNNING flag into core · e9ca8bf1

由 Marcel Holtmann 提交于 10月 04, 2015

Setting and clearing of HCI_RUNNING flag in each and every driver is
just duplicating the same code all over the place. So instead of having
the driver do it in their hdev->open and hdev->close callbacks, set it
globally in the core transport handling.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

e9ca8bf1

Bluetooth: Move HCI_RUNNING check into hci_send_frame · 73d0d3c8

由 Marcel Holtmann 提交于 10月 04, 2015

In all callbacks for hdev->send the status of HCI_RUNNING is checked. So
instead of repeating that code in every driver, move the check into the
hci_send_frame function before calling hdev->send.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

73d0d3c8

17 9月, 2015 3 次提交

Bluetooth: Remove SCO fragments on connection close · 8f9d02f4

由 Kuba Pawlak 提交于 9月 10, 2015

SCO packet reassembler may have a fragment of SCO packet, from
previous connection, cached and not removed when SCO connection
is ended. Packets from new SCO connection are then going to be
attached to that fragment, creating an invalid SCO packets.

Controllers like Intel's WilkinsPeak are always fragmenting
SCO packet into 3 parts (#1, #2, #3). Packet #1 contains
SCO header and audio data, others just audio data. if there is
a fragment cached from previous connection, i.e. #1, first
SCO packet from new connection is going to be attached to it
creating packet consisting of fragments #1-#1-#2. This will
be forwarded to upper layers. After that, fragment #3 is going
to be used as a starting point for another SCO packet.
It does not contain a SCO header, but the code expects it,
casts a SCO header structure on it, and reads whatever audio
data happens to be there as SCO packet length and handle.
From that point on, we are assembling random data into SCO
packets. Usually it recovers quickly as initial audio data
contains mostly zeros (muted stream), but setups of over
4 seconds were observed.
Issue manifests itself by printing on the console:
Bluetooth: hci0 SCO packet for unknown connection handle 48
Bluetooth: hci0 SCO packet for unknown connection handle 2560
Bluetooth: hci0 SCO packet for unknown connection handle 12288
It may also show random handles if audio data was non-zeroed.
Hcidump shows SCO packets with random length and handles.

Few messages with handle 0 at connection creation are OK
for some controllers (like WilkinsPeak), as there are SCO packets
with zeroed handle at the beginning (possible controller bug).
Few of such messages at connection end, with a handle looking
sane (around 256, 512, 768 ...) is also OK, as these are last
SCO packets that were assembled and sent up, before connection
was ended, but were not handled in time.

This issue may still manifest itself on WilkinsPeak as it sometimes,
at SCO connection creation, does not send third fragment of first
SCO packet (#1-#2-#1-#2-#3...). This is a firmware bug and this
patch does not address it.
Signed-off-by: NKuba Pawlak <kubax.t.pawlak@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

8f9d02f4

Bluetooth: btusb: Use btintel_load_ddc_config for device config · e924d3d6

由 Loic Poulain 提交于 9月 04, 2015

btintel_load_ddc_config is now part of btintel.
Signed-off-by: NLoic Poulain <loic.poulain@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

e924d3d6

Bluetooth: btusb: Detect new kind of counterfeit CSR controllers · 6cafcd95

由 Johan Hedberg 提交于 8月 30, 2015

Controllers claiming to be CSR with LMP subversion 0x0c5c don't
actually seem to be authentic CSR controllers. They also don't have
their USB bcdDevice value matching the LMP subversion like all other
CSR controllers:

HCI:

> HCI Event: Command Complete (0x0e) plen 12
      Read Local Version Information (0x04|0x0001) ncmd 1
        Status: Success (0x00)
        HCI version: Bluetooth 2.0 (0x03) - Revision 3164 (0x0c5c)
        LMP version: Bluetooth 2.0 (0x03) - Subversion 3164 (0x0c5c)
        Manufacturer: Cambridge Silicon Radio (10)

USB:

T: Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=16 #Cfgs= 1
P: Vendor=0a12 ProdID=0001 Rev= 1.34
C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms

These controllers also have the HCI_Read_Stored_Link_Key command
broken so it's important the right quirk is set for them.
Reported-and-tested-by: NRhobison Alves Pereira <rhobison@hotmail.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

6cafcd95

29 8月, 2015 1 次提交

Bluetooth: btusb: Correct typos based on checkpatch.pl · 5075edae

由 Minjune Kim 提交于 8月 27, 2015

Signed-off-by: NMinjune Kim <infinite.minjune.kim@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

5075edae

16 8月, 2015 1 次提交

Bluetooth: btusb: mark 0c10:0000 devices with BTUSB_SWAVE · 4481c076

由 Peter Poklop 提交于 8月 15, 2015

This patch enables quirk handling for Silicon Wave based devices and
fixes kernel bug with id 42985.

T:  Bus=01 Lev=01 Prnt=01 Port=07 Cnt=04 Dev#=  6 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0c10 ProdID=0000 Rev=15.00
S:  Manufacturer=SiW
S:  Product=SiW
S:  SerialNumber=340A05F61100
C:* #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr= 50mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NPeter Poklop <peter.poklop@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

4481c076

30 7月, 2015 1 次提交

Bluetooth: btusb: match generic class code in interface descriptor · d63b2826

由 Daniel Drake 提交于 7月 17, 2015

btusb currently has a generic match on USB device descriptors:
        { USB_DEVICE_INFO(0xe0, 0x01, 0x01) },

However, http://www.usb.org/developers/defined_class states:

  Base Class E0h (Wireless Controller)
  This base class is defined for devices that are Wireless controllers.
  Values not shown in the table below are reserved. These class codes are
  to be used in Interface Descriptors, with the exception of the Bluetooth
  class code which can also be used in a Device Descriptor.

Add a match on the interface descriptors accordingly.

This fixes compatibility with the RTL8723AU device shown below.
This device conforms to the USB Interface Association Descriptor
specification, which requires the device to have class ef/02/01.
The extra IAD descriptor then specifies that interfaces 0 and 1
belong to the same function/driver, which is true. Provided that
the Bluetooth device class spec accepts use of the IAD, I imagine that
technically, all btusb devices should be configured like this.

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  3 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0bda ProdID=0724 Rev= 2.00
S:  Manufacturer=Realtek
S:  Product=802.11n WLAN Adapter
S:  SerialNumber=00e04c000001
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=500mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 4 Cls=ff(vend.) Sub=ff Prot=ff Driver=rtl8723au
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=03(Int.) MxPS=  64 Ivl=500us
Signed-off-by: NDaniel Drake <drake@endlessm.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

d63b2826

23 7月, 2015 3 次提交

Bluetooth: btintel: Create common function for Intel version info · 7feb99e1

由 Marcel Holtmann 提交于 7月 05, 2015

The Intel version information is shared between USB and UART drivers
and with that move it into a generic function of the Intel module.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

7feb99e1

Bluetooth: btintel: Create common Intel Secure Send function · 09df123d

由 Marcel Holtmann 提交于 7月 05, 2015

The Intel Secure Send command is used the same in USB and UART drivers
and with that move a generic version into the Intel module.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

09df123d

Bluetooth: btusb: Use hardware error handler from Intel module · eeb6abe9

由 Marcel Holtmann 提交于 7月 05, 2015

The Intel specific Bluetooth module provides now an exported function
for the hardware error. Use that instead of duplicating it inside the
driver.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

eeb6abe9

19 6月, 2015 1 次提交

Bluetooth: ath3k: Add support of 04ca:300d AR3012 device · 7e730c7f

由 Dmitry Tunin 提交于 6月 18, 2015

BugLink: https://bugs.launchpad.net/bugs/1394368

This device requires new firmware files
 AthrBT_0x11020100.dfu and ramps_0x11020100_40.dfu added to
/lib/firmware/ar3k/ that are not included in linux-firmware yet.

T: Bus=02 Lev=01 Prnt=01 Port=04 Cnt=03 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=04ca ProdID=300d Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: NDmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

7e730c7f

17 6月, 2015 1 次提交

Bluetooth: btusb: Add routine for applying Intel DDC parameters · 52cc9168

由 Tedd Ho-Jeong An 提交于 6月 12, 2015

This patch adds the routine to apply the DDC parameter from device
specific ddc file.

Once the device is rest to operational mode, optionally, it can
download the device specific configration (DDC) parameters before
the BlueZ starts the stack initialization.

It opens the DDC file based on HW_VARIANT and DEV_REVISION and
send ID/Value with HCI_Intel_Write_DDC command.

Format of DDC file
DDC file contains one or more number of DDC structure.

DDC Structure
It has 'Length' field of one octet, DDC 'ID' field of
two octets followed by the array of DDC 'Value' that gives
the value of parameters itself.
'Length' contains the length of DDC 'ID' and DDC 'Value'.

+------------+----------+
| Size(byte) |    Name  |
+------------+----------+
|      1     | Length   |
+------------+----------+
|      2     | ID       |
+------------+----------+
| Length - 2 | Value    |
+------------+----------+
Signed-off-by: NTedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

52cc9168

09 6月, 2015 1 次提交

Bluetooth: btusb: Fix secure send command length alignment on Intel 8260 · e66890a9

由 Marcel Holtmann 提交于 6月 07, 2015

This patch fixes the command length alignment issue for Intel Bluetooth
8260.

The length of parameters in the firmware downloading command must be
multiplication of 4. If not, the command must append Intel_NOP command
with extra parameters, zeros, at the end, and the firmware file is
already included Intel_NOP command for alignment.

This patch checks the next command and if the next command is Intel_NOP
command, it reads the Intel_NOP command and send them together.

For example, if the data from the firmware file looks like this:
8E FC 03 11 22 33 02 FC 03 00 00 00

Previously, btusb sends two commands:
09 FC 06 8E FC 03 11 22 33
09 FC 06 02 FC 03 00 00 00

This won't work because the length of parameters are 6 which violates
the 4 byte alignment.

This patch will append them together and send as one command:
09 FC 0C 8E FC 03 11 22 33 02 FC 03 00 00 00

Based on previous work from Tedd Ho-Jeong An <tedd.an@intel.com>
Reported-by: NTedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Tested-by: NTedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org

e66890a9

08 6月, 2015 4 次提交

Bluetooth: btusb: Correct typo in Roper Class 1 Bluetooth Dongle · 2eeac871

由 Aleksei Volkov 提交于 6月 08, 2015

That patch corrects the typo in usb vendor id for Roper Class 1 Bluetooth
Dongle. Problem with typo is present since 4.0 kernel.

Content /sys/kernel/debug/usb/devices for these dongle:

T:  Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1310 ProdID=0001 Rev=15.00
S:  Manufacturer=SiW
S:  Product=SiW
S:  SerialNumber=E7BB050D0B00
C:* #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr= 50mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NAleksei Volkov <info@dv2c.ru>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 4.0.x

2eeac871

Bluetooth: btusb: Remove unneeded btusb_read_local_version function · 7cd84d72

由 Marcel Holtmann 提交于 6月 07, 2015

The btusb_read_local_version function has only a single user and with
that just move its functionality in place where it belongs.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

7cd84d72

Bluetooth: btusb: Remove double error check from local version command · 9641d343

由 Marcel Holtmann 提交于 6月 07, 2015

The __hci_cmd_sync function already handles the command status and
command complete errors. No need to check the status field again.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

9641d343

Bluetooth: btusb: Fix memory leak in Intel setup routine · ecffc804

由 Marcel Holtmann 提交于 6月 07, 2015

The SKB returned from the Intel specific version information command is
missing a kfree_skb.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org

ecffc804

openanolis / cloud-kernel 1 年多 前同步成功

openanolis / cloud-kernel
1 年多前同步成功