In a LOWMEM condition an ERP notification would have been sent twice
causing an unpredictable behaviour of the ERP.
Signed-off-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

When calling fc_remote_port_add make sure to not call it again before
fc_remote_port_delete has been called. In other words, ensure to
create a new fc_rport, then delete it, then create a new one again.
Reviewed-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Depending on interruptions on some storage systems, the complete
channel can stall which looks like an outbound queue stall to Linux.
When trying to acquire a free SBAL for a non-SCSI command, zfcp waits
for 5 seconds for a free slot to appear. This is the right place to
detect a queue stall: If the wait times out, we assume a stalled queue
and try to recover this.

The overall strategy should be to trigger the erp from specific
events, and not try an overall escalation from one failed port to a
full-blown queue recovery. If we manage to send a command, the status
codes for this command or a timeout will trigger the right follow-on
actions.
Reviewed-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

If an action fails, retry it until the erp count exceeds the
threshold. If there is something fundamentally wrong, the FSF layer
will trigger a more appropriate action depending on the FSF status
codes.

The followup for successful actions is a different followup than
retrying failed actions, so split the code two functions to make this
clear.
Reviewed-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

After closing the port, we want it to be "not open" to consider the
action to be successful.
Reviewed-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

-ENOMEM is for memory allocation problems, -EIO for queue/SBAL
allocation problems.
Reviewed-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The ELS ADISC and the GID_PN requests sent from zfcp fit into
unchained FSF requests. Change the FSF allocation logic to use
unchained requests whenever possible where everything fits in one
SBAL. This avoids acquiring more SBALs than necessary, especially
during zfcp recovery when things might be stalled.
Reviewed-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

zfcp_erp_notify uses the ZFCP_ERP_STATUS_* flags, so it is
ZFCP_STATUS_ERP_LOWMEM instead of ZFCP_ERP_NOMEM. Signalling
ZFCP_ERP_FAILED is not necessary, the missing d_id will show that the
nameserver did not return the d_id.
Reviewed-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

When a fsf_req or a qtcb cannot be allocated return -ENOMEM instead of
-EIO.
Reviewed-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

req_q_util is not atomic, so the qdio_stat_lock must be held when
reading this variable.
Reviewed-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

We should not modify the port status after triggering an ERP action
for the port. It is not guaranteed which status is finally active
when the ERP action is performed. This can lead to situations which
are unwanted and hard to debug in case of a failure.
Signed-off-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
  It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT

  This will make hardirq.h inclusion cheaper for every PREEMPT=n config
  (which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

From: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: NMichael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

remove loop, add some debug data and use get_sense function
Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Fix this:

drivers/s390/char/monreader.c: In function 'mon_open':
drivers/s390/char/monreader.c:323: warning: passing argument 1 of 'dev_set_drvdata' from incompatible pointer type
include/linux/device.h:457: note: expected 'struct device *' but argument is of type 'struct device **'
drivers/s390/char/monreader.c: In function 'monreader_freeze':
drivers/s390/char/monreader.c:466: warning: passing argument 1 of 'dev_get_drvdata' from incompatible pointer type
include/linux/device.h:452: note: expected 'const struct device *' but argument is of type 'struct device **'
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Define an empty static inline version of sclp_console_pm_event()
to fix the build error below for !SCLP_CONSOLE.

drivers/s390/built-in.o: In function `sclp_rw_pm_event':
sclp_rw.c:(.text+0x12f68): undefined reference to `sclp_console_pm_event'
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

To set a dasd online dasd_change_state is called twice. The first
cycle will schedule initial analysis of the device, set the rc to
-EAGAIN and will not touch the device state any more.
The initial analysis will in turn call dasd_change_state to increase
the state to the final DASD_STATE_ONLINE.

If the dasd_change_state on the second thread outruns the other one
both finish with the state set to DASD_STATE_ONLINE and the device
refcount will be decreased by 2.

Fix this by leaving dasd_change_state on rc == -EAGAIN so that the
refcount will always be decreased by 1.
Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Replace the remaining direct accesses to the driver_data pointer
with calls to the dev_get_drvdata() and dev_set_drvdata() functions.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The stop flags are handled in the generic restore function so the
stop flag is removed also for FBA and DIAG devices.
Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Add Suspend/Resume support to ap bus and zcrypt. All enhancements are
done in the ap bus. No changes in the crypto card specific part are
necessary.
Signed-off-by: NFelix Beck <felix.beck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Remove unneeded sanity checks from do_QDIO since this is the hot path.
Change the type of bufnr and count to unsigned int so the check for the
maximum value works.
Reported-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

It is not required to change the state of primed SBALs. Leaving them
primed saves a SQBS instruction under z/VM.
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Since the adapter interrupt tasklet only schedules the queue tasklets
and contains no code that requires serialization in can be merged
with the adapter interrupt handler. That possibly safes some CPU
cycles.
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

For devices without QIOASSIST primed SBALS were extracted in a loop.
Remove the loop since get_buf_states can already return more than
one primed SBAL.
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The check whether qdio runs under z/VM was incorrect since SIGA-Sync is not
set if the device runs with QIOASSIST. Use MACHINE_IS_VM instead to prevent
polling under z/VM.

Merge qdio_inbound_q_done and tiqdio_is_inbound_q_done.
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Move the adapter interrupt tasklet function to the qdio main code
since all the functions used by the tasklet are located there.
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

When syncing the sclp console queue, we call del_timer_sync() while holding
the "sclp_con_lock" spinlock. This lock is also taken in the timer function
"sclp_console_timeout". Therefore the sync version of del_timer() cannot be
used here. Because the synchronous deletion of the timer is only needed
in the suspend callback and in that case only one CPU is remaining and
therefore it is not possible that the timer function is running in parallel,
we can safely use del_timer() instead of del_timer_sync().
Signed-off-by: NMichael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The slab allocator is earlier available so convert the
bootmem allocations to slab/gfp allocations.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The slab allocator is earlier available so convert the
bootmem allocations to slab/gfp allocations.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The slab allocator is earlier available so convert the
bootmem allocations to slab/gfp allocations.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The slab allocator is earlier available so convert the
bootmem allocations to slab/gfp allocations.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

This patch is inspired by patch recently posted by Johannes Berg. Basically what
my patch does is to group list and a count of addresses into newly introduced
structure netdev_hw_addr_list. This brings us two benefits:
1) struct net_device becames a bit nicer.
2) in the future there will be a possibility to operate with lists independently
   on netdevices (with exporting right functions).
I wanted to introduce this patch before I'll post a multicast lists conversion.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>

 drivers/net/bnx2.c              |    4 +-
 drivers/net/e1000/e1000_main.c  |    4 +-
 drivers/net/ixgbe/ixgbe_main.c  |    6 +-
 drivers/net/mv643xx_eth.c       |    2 +-
 drivers/net/niu.c               |    4 +-
 drivers/net/virtio_net.c        |   10 ++--
 drivers/s390/net/qeth_l2_main.c |    2 +-
 include/linux/netdevice.h       |   17 +++--
 net/core/dev.c                  |  130 ++++++++++++++++++--------------------
 9 files changed, 89 insertions(+), 90 deletions(-)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NGerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NGerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NGerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Introduce the power management callbacks to the 3270 driver. On suspend
the current 3270 view is deactivated and for non-console 3270 device
the release callback is done. This disconnects the current tty /
fullscreen application from the 3270 device. On resume the current
view is reactivated, on the tty you get a fresh login.
If the system panics before the 3270 device has been resumed, the ccw
device for the 3270 console is reactivated with ccw_device_force_console.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Create dummy iucv-device to get control when the system is suspended
and resumed. Server the smsg iucv path on suspend, reestablish the
path on resume.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Patch establishes a dummy netiucv device to make sure iucv is notified
about suspend/resume even if netiucv is the only loaded iucv-exploting
module without any real net_device defined.

The PM freeze callback closes all open netiucv connections. Thus the
corresponding iucv path is removed.
The PM thaw/restore callback re-opens previously closed netiucv
connections.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The SCLP base driver defines a new notifier call back for all upper level SCLP
drivers, like the SCLP console, etc. This guarantees that in suspend first the
upper level drivers are suspended and afterwards the SCLP base driver. For
resume it is the other way round. The SCLP base driver itself registers a
new platform device at the platform bus and gets PM notifications via
the dev_pm_ops.

In suspend, the SCLP base driver switches off the receiver and sender mask
This is done in sclp_deactivate(). After suspend all new requests will be
rejected with -EIO and no more interrupts will be received, because the masks
are switched off. For resume the sender and receiver masks are reset in
the sclp_reactivate() function.

When the SCLP console is suspended, all new messages are cached in the
sclp console buffers. In resume, all the cached messages are written to the
console. In addition to that we have an early resume function that removes
the cached messages from the suspend image.
Signed-off-by: NMichael Holzheu <holzheu@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>