The enet IP only support 32 bit, it will use swiotlb buffer to do dma
mapping when xmit buffer DMA memory address is bigger than 4G in i.MX
platform. After stress suspend/resume test, it will print out:

log:
[12826.352864] fec 5b040000.ethernet: swiotlb buffer is full (sz: 191 bytes)
[12826.359676] DMA: Out of SW-IOMMU space for 191 bytes at device 5b040000.ethernet
[12826.367110] fec 5b040000.ethernet eth0: Tx DMA memory map failed

The issue is that the ready xmit buffers that are dma mapped but DMA still
don't copy them into fifo, once MAC restart, these DMA buffers are not unmapped.
So it should check the dma mapping buffer and unmap them.
Signed-off-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Under some circumstances driver will perform PHY reset in
ksz9031_read_status() to fix autoneg failure case (idle error count =
0xFF). When this happens ksz9031 will not detect link status change any
more when connecting to Netgear 1G switch (link can be recovered sometimes by
restarting netdevice "ifconfig down up"). Reproduced with TI am572x board
equipped with ksz9031 PHY while connecting to Netgear 1G switch.

Fix the issue by reconfiguring autonegotiation after PHY reset in
ksz9031_read_status().

Fixes: d2fd719b ("net/phy: micrel: Add workaround for bad autoneg")
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ensure that we mark AN as enabled at boot time, rather than leaving
it disabled.  This is noticable if your SFP module is fiber, and
it supports faster speeds than 1G with 2.5G support in place.

Fixes: 9525ae83 ("phylink: add phylink infrastructure")
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When setting the ethtool settings, ensure that the validated PHY
interface mode is propagated to the current link settings, so that
2500BaseX can be selected.

Fixes: 9525ae83 ("phylink: add phylink infrastructure")
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 966a9671 randomly added alignment to this structure, but
it's actually detrimental to performance of null_blk. Test case:

Running on both the home and remote node shows a ~5% degradation
in performance.

While in there, move blk_status_t to the hole after the integer tag
in the nullb_cmd structure. After this patch, we shrink the size
from 192 to 152 bytes.

Fixes: 966a9671 ("smp: Avoid using two cache lines for struct call_single_data")
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Make sure to check both return code fields before processing the
response. Otherwise we risk operating on invalid data.

Fixes: c9475369 ("s390/qeth: rework RX/TX checksum offload")
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After TC offloads were converted to callbacks we have no choice
but keep track of the offloaded filter in the driver.

The check for nn->dp.bpf_offload_xdp was a stop gap solution
to make sure failed TC offload won't disable XDP, it's no longer
necessary.  nfp_net_bpf_offload() will return -EBUSY on
TC vs XDP conflicts.

Fixes: 3f7889c4 ("net: sched: cls_bpf: call block callbacks for offload")
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

cls_bpf used to take care of tracking what offload state a filter
is in, i.e. it would track if offload request succeeded or not.
This information would then be used to issue correct requests to
the driver, e.g. requests for statistics only on offloaded filters,
removing only filters which were offloaded, using add instead of
replace if previous filter was not added etc.

This tracking of offload state no longer functions with the new
callback infrastructure.  There could be multiple entities trying
to offload the same filter.

Throw out all the tracking and corresponding commands and simply
pass to the drivers both old and new bpf program.  Drivers will
have to deal with offload state tracking by themselves.

Fixes: 3f7889c4 ("net: sched: cls_bpf: call block callbacks for offload")
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are few reasons in mvneta_rx_swbm() function when received packet
is dropped. mvneta_rx_error() should be called only if error bit [16]
is set in rx descriptor.

[gregory.clement@free-electrons.com: add fixes tag]
Cc: stable@vger.kernel.org
Fixes: dc35a10f ("net: mvneta: bm: add support for hardware buffer management")
Signed-off-by: NYelena Krivosheev <yelena@marvell.com>
Tested-by: NDmitri Epshtein <dima@marvell.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When adding the RX queue association with each CPU, a typo was made in
the mvneta_cleanup_rxqs() function. This patch fixes it.

[gregory.clement@free-electrons.com: add commit log and fixes tag]
Cc: stable@vger.kernel.org
Fixes: 2dcf75e2 ("net: mvneta: Associate RX queues with each CPU")
Signed-off-by: NYelena Krivosheev <yelena@marvell.com>
Tested-by: NDmitri Epshtein <dima@marvell.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When port connect to PHY in polling mode (with poll interval 1 sec),
port and phy link status must be synchronize in order don't loss link
change event.

[gregory.clement@free-electrons.com: add fixes tag]
Cc: <stable@vger.kernel.org>
Fixes: c5aff182 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Signed-off-by: NYelena Krivosheev <yelena@marvell.com>
Tested-by: NDmitri Epshtein <dima@marvell.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During unload, on mlx5_stop_eqs we move command interface from events
mode to polling mode, but if command interface EQ destroy fail we move
back to events mode.
That's wrong since even if we fail to destroy command interface EQ, we
do release its irq, so no interrupts will be received.

Fixes: e126ba97 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

When mlx5_stop_eqs fails to destroy any of the eqs it returns with an error.
In such failure flow the function will return without
releasing all EQs irqs and then pci_free_irq_vectors will fail.
Fix by only warn on destroy EQ failure and continue to release other
EQs and their irqs.

It fixes the following kernel trace:
kernel: kernel BUG at drivers/pci/msi.c:352!
...
...
kernel: Call Trace:
kernel: pci_disable_msix+0xd3/0x100
kernel: pci_free_irq_vectors+0xe/0x20
kernel: mlx5_load_one.isra.17+0x9f5/0xec0 [mlx5_core]

Fixes: e126ba97 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Flow steering priority and namespace are software only objects that
didn't have the proper destructors and were not freed during steering
cleanup.

Fix it by adding destructor functions for these objects.

Fixes: bd71b08e ("net/mlx5: Support multiple updates of steering rules in parallel")
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

When calling add/remove VXLAN port, a lock must be held in order to
prevent race scenarios when more than one add/remove happens at the
same time.
Fix by holding our state_lock (mutex) as done by all other parts of the
driver.
Note that the spinlock protecting the radix-tree is still needed in
order to synchronize radix-tree access from softirq context.

Fixes: b3f63c3d ("net/mlx5e: Add netdev support for VXLAN tunneling")
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

A refcount mechanism must be implemented in order to prevent unwanted
scenarios such as:
- Open an IPv4 VXLAN interface
- Open an IPv6 VXLAN interface (different socket)
- Remove one of the interfaces

With current implementation, the UDP port will be removed from our VXLAN
database and turn off the offloads for the other interface, which is
still active.
The reference count mechanism will only allow UDP port removals once all
consumers are gone.

Fixes: b3f63c3d ("net/mlx5e: Add netdev support for VXLAN tunneling")
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

mlx5e_vxlan_lookup_port is called both from mlx5e_add_vxlan_port (user
context) and mlx5e_features_check (softirq), but the lock acquired does
not disable bottom half and might result in deadlock. Fix it by simply
replacing spin_lock() with spin_lock_bh().
While at it, replace all unnecessary spin_lock_irq() to spin_lock_bh().

lockdep's WARNING: inconsistent lock state
[  654.028136] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[  654.028229] swapper/5/0 [HC0[0]:SC1[9]:HE1:SE0] takes:
[  654.028321]  (&(&vxlan_db->lock)->rlock){+.?.}, at: [<ffffffffa06e7f0e>] mlx5e_vxlan_lookup_port+0x1e/0x50 [mlx5_core]
[  654.028528] {SOFTIRQ-ON-W} state was registered at:
[  654.028607]   _raw_spin_lock+0x3c/0x70
[  654.028689]   mlx5e_vxlan_lookup_port+0x1e/0x50 [mlx5_core]
[  654.028794]   mlx5e_vxlan_add_port+0x2e/0x120 [mlx5_core]
[  654.028878]   process_one_work+0x1e9/0x640
[  654.028942]   worker_thread+0x4a/0x3f0
[  654.029002]   kthread+0x141/0x180
[  654.029056]   ret_from_fork+0x24/0x30
[  654.029114] irq event stamp: 579088
[  654.029174] hardirqs last  enabled at (579088): [<ffffffff818f475a>] ip6_finish_output2+0x49a/0x8c0
[  654.029309] hardirqs last disabled at (579087): [<ffffffff818f470e>] ip6_finish_output2+0x44e/0x8c0
[  654.029446] softirqs last  enabled at (579030): [<ffffffff810b3b3d>] irq_enter+0x6d/0x80
[  654.029567] softirqs last disabled at (579031): [<ffffffff810b3c05>] irq_exit+0xb5/0xc0
[  654.029684] other info that might help us debug this:
[  654.029781]  Possible unsafe locking scenario:

[  654.029868]        CPU0
[  654.029908]        ----
[  654.029947]   lock(&(&vxlan_db->lock)->rlock);
[  654.030045]   <Interrupt>
[  654.030090]     lock(&(&vxlan_db->lock)->rlock);
[  654.030162]
 *** DEADLOCK ***

Fixes: b3f63c3d ("net/mlx5e: Add netdev support for VXLAN tunneling")
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

In error flow, when DESTROY_QP command should be executed, the wrong
mailbox was set with data, not the one that is written to hardware,
Fix that.

Fixes: 09a7d9ec '{net,IB}/mlx5: QP/XRCD commands via mlx5 ifc'
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Fix misspelling in word syndrome.

Fixes: e126ba97 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Fixes the bug when turning on/off CQE compression mechanism
resets the RX rings size to default value when it is not
needed.

Fixes: 2fc4bfb7 ("net/mlx5e: Dynamic RQ type infrastructure")
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

The assumption that the next header field contains the transport
protocol is wrong for IPv6 packets with extension headers.
Instead, we should look the inner-most next header field in the buffer.
This will fix TSO offload for tunnels over IPv6 with extension headers.

Performance testing: 19.25x improvement, cool!
Measuring bandwidth of 16 threads TCP traffic over IPv6 GRE tap.
CPU: Intel(R) Xeon(R) CPU E5-2660 v2 @ 2.20GHz
NIC: Mellanox Technologies MT28800 Family [ConnectX-5 Ex]
TSO: Enabled
Before: 4,926.24  Mbps
Now   : 94,827.91 Mbps

Fixes: b3f63c3d ("net/mlx5e: Add netdev support for VXLAN tunneling")
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Fix bug that allows ets bw sum to be 0% when ets tc type exists.

Fixes: 08fb1dac ('net/mlx5e: Support DCBNL IEEE ETS')
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Reviewed-by: NHuy Nguyen <huyn@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

In mlx5_ifc, struct size was not complete, and thus driver was sending
garbage after the last defined field. Fixed it by adding reserved field
to complete the struct size.

In addition, rename all set_rate_limit to set_pp_rate_limit to be
compliant with the Firmware <-> Driver definition.

Fixes: 7486216b ("{net,IB}/mlx5: mlx5_ifc updates")
Fixes: 1466cc5b ("net/mlx5: Rate limit tables support")
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Before the offending commit, mlx5 core did the IRQ affinity itself,
and it seems that the new generic code have some drawbacks and one
of them is the lack for user ability to modify irq affinity after
the initial affinity values got assigned.

The issue is still being discussed and a solution in the new generic code
is required, until then we need to revert this patch.

This fixes the following issue:
echo <new affinity> > /proc/irq/<x>/smp_affinity
fails with  -EIO

This reverts commit a435393a.
Note: kept mlx5_get_vector_affinity in include/linux/mlx5/driver.h since
it is used in mlx5_ib driver.

Fixes: a435393a ("mlx5: move affinity hints assignments to generic code")
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jes Sorensen <jsorensen@fb.com>
Reported-by: NJes Sorensen <jsorensen@fb.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Currently, if a size of zero is passed to
mlx5_fpga_mem_{read|write}_i2c()
the "err" return value will not be initialized, which triggers gcc
warnings:

[..]/mlx5/core/fpga/sdk.c:87 mlx5_fpga_mem_read_i2c() error:
uninitialized symbol 'err'.
[..]/mlx5/core/fpga/sdk.c:115 mlx5_fpga_mem_write_i2c() error:
uninitialized symbol 'err'.

fix that.

Fixes: a9956d35 ('net/mlx5: FPGA, Add SBU infrastructure')
Signed-off-by: NKamal Heib <kamalh@mellanox.com>
Reviewed-by: NYevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

As noted in dwmac4_wrback_get_rx_timestamp_status the timestamp is found
in the context descriptor following the current descriptor. However the
current code looks for the context descriptor in the current
descriptor, which will always fail.
Signed-off-by: NFredrik Hallenberg <megahallon@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using GMAC4 the value written in PTP_SSIR should be shifted however
the shifted value is also used in subsequent calculations which results
in a bad timestamp value.
Signed-off-by: NFredrik Hallenberg <megahallon@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unlike ip tunnels, now vxlan doesn't do any pmtu update for
upper dst pmtu, even if it doesn't match the lower dst pmtu
any more.

The problem can be reproduced when reducing the vxlan lower
dev's pmtu when running netperf. In jianlin's testing, the
performance went to 1/7 of the previous.

This patch is to update the upper dst pmtu to match the lower
dst pmtu on tx path so that packets can be sent out even when
lower dev's pmtu has been changed.

It also works for metadata dst.

Note that this patch doesn't process any pmtu icmp packet.
But even in the future, the support for pmtu icmp packets
process of udp tunnels will also needs this.

The same thing will be done for geneve in another patch.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Under certain conditions EMAC stop reception of incoming packets and
continuously increment R_MISS register instead of saving data into
provided buffer. The commit implement workaround for such situation.
Then the stall detected EMAC will be restarted.

On device the stall looks like the device lost it's dynamic IP address.
ifconfig shows that interface error counter rapidly increments.
At the same time on the DHCP server we can see continues DHCP-requests
from device.

In real network stalls happen really rarely. To make them frequent the
broadcast storm[1] should be simulated. For simulation it is necessary
to make following connections:
    1. connect radxarock to 1st port of switch
    2. connect some PC to 2nd port of switch
    3. connect two other free ports together using standard ethernet cable,
       in order to make a switching loop.

After that, is necessary to make a broadcast storm. For example, running on
PC 'ping' to some IP address triggers ARP-request storm. After some
time (~10sec), EMAC on rk3188 will stall.

Observed and tested on rk3188 radxarock.

[1] https://en.wikipedia.org/wiki/Broadcast_radiationSigned-off-by: NAlexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

arc_emac_rx() has some issues found by code review.

In case netdev_alloc_skb_ip_align() or dma_map_single() failure
rx fifo entry will not be returned to EMAC.

In case dma_map_single() failure previously allocated skb became
lost to driver. At the same time address of newly allocated skb
will not be provided to EMAC.
Signed-off-by: NAlexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current solution would setup fixed and force link of 1Gbps to the both
GMAC on the default. However, The GMAC should always be put to link down
state when the GMAC is disabled on certain target boards. Otherwise,
the driver possibly receives unexpected data from the floating hardware
connection through the unused GMAC. Although the driver had been added
certain protection in RX path to get rid of such kind of unexpected data
sent to the upper stack.
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 63dd00fa.

RAUHT DELETE_ALL seems to trigger a bug in FW. That manifests by later
calls to RAUHT ADD of an IPv6 neighbor to fail with "bad parameter"
error code.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Fixes: 63dd00fa ("mlxsw: spectrum_router: Add batch neighbour deletion")
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes a hang issue seen when changing the MTU size from 1500 MTU
to 9000 MTU on both 5717 and 5719 chips. In discussion with Broadcom,
they've indicated that these chipsets have the same phy as the 57766
chipset, so the same workarounds apply. This has been tested by IBM
on both Power 8 and Power 9 systems as well as by Broadcom on x86
hardware and has been confirmed to resolve the hang issue.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The only part of atmel_spi_remove which needs to be atomic is hardware
reset.

atmel_spi_stop_dma calls dma_terminate_all and this needs interrupts
enabled.
atmel_spi_release_dma calls dma_release_channel and dma_release_channel
locks a mutex inside of spin_lock.

So the call of these functions can't be inside a spin_lock.
Reported-by: NJia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: NRadu Pirea <radu.pirea@microchip.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The driver may sleep under a spinlock.
The function call path is:
hwsim_get_radio_nl (acquire the spinlock)
  nlmsg_new(GFP_KERNEL) --> may sleep

To fix it, GFP_KERNEL is replaced with GFP_ATOMIC.

This bug is found by my static analysis tool(DSAC) and checked by my code review.
Signed-off-by: NJia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Same as in ieee80211_nullfunc_get, enable the TODS bit, otherwise the
nullfunc packet will not be handled in ap rx path.
(will be dropped in ieee80211_accept_frame()).
Signed-off-by: NAdiel Aloni <adiel.aloni@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Commit caa4b024(blk-map: call blk_queue_bounce from blk_rq_append_bio)
moves blk_queue_bounce() into blk_rq_append_bio(), but don't consider
the fact that the bounced bio becomes invisible to caller since the
parameter type is 'struct bio *'. Make it a pointer to a pointer to
a bio, so the caller sees the right bio also after a bounce.

Fixes: caa4b024 ("blk-map: call blk_queue_bounce from blk_rq_append_bio")
Cc: Christoph Hellwig <hch@lst.de>
Reported-by: NMichele Ballabio <barra_cuda@katamail.com>
(handling failure of blk_rq_append_bio(), only call bio_get() after
blk_rq_append_bio() returns OK)
Tested-by: NMichele Ballabio <barra_cuda@katamail.com>
Signed-off-by: NMing Lei <ming.lei@redhat.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

There are several error paths in xgene_mdio_probe(),
where clk is left undisabled. The patch fixes them.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Observed on the 88e1512 in SGMII-to-Copper mode, negotiating pause
is unreliable.  While the pause bits can be set in the advertisment
register, they clear shortly after negotiation with a link partner
commences irrespective of the cause of the negotiation.

While these bits may be correctly conveyed to the link partner on the
first negotiation, a subsequent negotiation (eg, due to negotiation
restart by the link partner, or reconnection of the cable) will result
in the link partner seeing these bits as zero, while the kernel
believes that it has advertised pause modes.

This leads to the local kernel evaluating (eg) symmetric pause mode,
while the remote end evaluates that we have no pause mode capability.

Since we can't guarantee the advertisment, disable pause mode support
with this PHY when used in SGMII-to-Copper mode.

The 88e1510 in RGMII-to-Copper mode appears to behave correctly.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the order of mac_up and sgmii_open for the
reasons noted below:

- If open takes more time(if the SGMII block is not responding or
  if we want to do some delay based task) in this situation we
  will hit NETDEV watchdog
- The main reason : We should signal to upper layers that we are
  ready to receive packets "only" when the entire path is initialized
  not the other way around, this is followed in the reset path where
  we do mac_down, sgmii_reset and mac_up. This also makes the driver
  uniform across the reset and open paths.
- In the future there may be need for delay based tasks to be done in
  sgmii open which will result in NETDEV watchdog
- As per the documentation the order of init should be sgmii, mac, rings
  and DMA
Signed-off-by: NHemanth Puranik <hpuranik@codeaurora.org>
Acked-by: NTimur Tabi <timur@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>