Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is needed as part of making the various IT87 drivers actually co-exist
politely with each other, and with other superio devices that may be muxed
on 0x2E/0x2F.

It can be applied before or after the other patches by Nat Gurumoorthy without
problem.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Xilinx PS Uart is used on the new ARM based SoC. This
UART is not compatible with others such that a seperate
driver is required.
Signed-off-by: NJohn Linn <john.linn@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use the standard mechanism to print a hex buffer
to eliminate empty printf warning.

A couple % smaller text and data too.

$ size drivers/tty/n_gsm.o*
   text	   data	    bss	    dec	    hex	filename
  23543	    312	   6376	  30231	   7617	drivers/tty/n_gsm.o.new
  24051	    408	   6496	  30955	   78eb	drivers/tty/n_gsm.o.old
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The tty value that should be put is the one that was just gotten by
tty_port_tty_get, not the one that is the argument to the enclosing
function.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@exists@
local idexpression struct tty_struct *x;
expression ra,rr;
statement S1,S2;
@@

x = tty_port_tty_get(...)
... when != x = rr
    when any
    when != tty_kref_put(x,...)
    when != if (...) { ... tty_kref_put(x,...) ...}
(
if(<+...x...+>) S1 else S2
|
if(...) { ... when != x = ra
     when forall
     when != tty_kref_put(x,...)
*return...;
}
)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

tty_write_lock and tty_write_unlock contain imbalanced locking. But
this is intentional, so mark them appropriately by
__acquires/__releases.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

msleep* is guaranteed to return with TASK_RUNNING task state. And
since there is no other set_task_state in the paths of
uart_wait_until_sent, we need not to set_task_state to TASK_RUNNING.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

tty->index (named here as line) is set up in initialize_tty_struct.
The value is checked in get_tty_driver for the found driver as:
	if (device < base || device >= base + p->num)
		continue;
	*index = device - base;

So index/line can never be more than driver->num. Hence remove this
test from uart_open.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

moxa_write can be called from atomic context with irqs disabled (from
ppp_async_push). Don't enable interrupts by spin_unlock_bh as this
might cause deadlocks in the ppp layer.

Instead, use irqsave/irqrestore spin_lock functions.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

tty_sem used to protect tty open count. This was removed in 33dd474a
but the lock remained in place.

So remove it completely as it protects nothing now.

Also this solves Mac's problem with inatomic operation called from
atomic context (ppp):
BUG: scheduling while atomic: firefox-bin/1992/0x10000800
Modules linked in: ...
Pid: 1992, comm: firefox-bin Not tainted 2.6.38 #1
Call Trace:
...
 [] ? mutex_lock+0xe/0x21
 [] ? ntty_write+0x5d/0x192 [nozomi]
 [] ? __mod_timer.clone.30+0xbe/0xcc
 [] ? check_preempt_curr+0x60/0x6d
 [] ? __nf_ct_refresh_acct+0x75/0xbe
 [] ? ppp_async_push+0xa9/0x3bd [ppp_async]
 [] ? ppp_async_send+0x34/0x40 [ppp_async]
 [] ? ppp_push+0x6c/0x4f9 [ppp_generic]
...
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Reported-by: NMac <kmac@poczta.fm>
Tested-by: NGerald Pfeifer <gerald@pfeifer.com>
Reviewed-by: NJack Stone <jwjstone@fastmail.fm>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Before 33dd474a, these were some kind of protection against race with
HUP. They were protected with port->tty_sem at the same time.

By that commit, the counting was switched to tty_port's one, but the
locking remained the old one. So the count was not protected by
any lock anymore.

The driver should not test whether it raced with HUP or not anyways.
With the new refcounted tty model, it just should proceed as nothing
happened because all needed info is still there. In respect to this,
let's drop the useless and unprotected tests (tty_port->count is
protected by tty_port->lock).
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Tested-by: NGerald Pfeifer <gerald@pfeifer.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The allocation was moved to probe function in 9842c38e. And we can
sleep there. So allocate the 4*8192 bytes as GFP_KERNEL to mitigate
the allocation failure.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Tested-by: NGerald Pfeifer <gerald@pfeifer.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

it makes it simpler to keep track of the amount of
bytes received and simplifies how flush_to_ldisc counts
the remaining bytes. It also fixes a bug of lost bytes
on n_tty when flushing too many bytes via the USB
serial gadget driver.
Tested-by: NStefan Bigler <stefan.bigler@keymile.com>
Tested-by: NToby Gray <toby.gray@realvnc.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove stale code in serial_core layer.

Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Traditional \E[2J sequence erases console display but scroll-back
buffer and underlying device (frame) buffer keep data that can be
accessed by scrolling console back.

This patch introduce new \E[J parameter 3 that allows to scramble
scroll-back buffer explicitly. Session locking programs (screen,
vlock) can use it to prevent attacker to browse locked console
history.
Signed-off-by: NPetr Písař <ppisar@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Including linux/tty.h 3 times is a little over the top - once will do.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

remove invalid location line in each file header after location
moved from driver/char to driver/tty
Signed-off-by: NJovi Zhang <bookjovi@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Now, uart_update_termios is empty, so it's time to remove it. We no
longer need a live tty in .dtr_rts. So this should prune all the bugs
where tty is zeroed in port->tty during tty_port_block_til_ready.

There is one thing to note. We don't set ASYNC_NORMAL_ACTIVE now. It's
because this is done already in tty_port_block_til_ready.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In .dtr_rts we do:
  uart_set_mctrl(uport, TIOCM_DTR | TIOCM_RTS)
and call uart_update_termios. It does:
  uart_set_mctrl(port, TIOCM_DTR | TIOCM_RTS)
once again. As the only callsite of uart_update_termios is .dtr_rts,
remove the uart_set_mctrl from uart_update_termios to not set it twice.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We should not fiddle with speed and cflags in .dtr_rts hook. Actually
we might not have tty at that moment already.

So move the console cflag copy and speed setup into uart_startup.
Actually the speed setup is already there, but we need to call it
unconditionally (uart_startup is called from uart_open with hw_init =
0).

This means we move uart_change_speed before dtr/rts setup in .dtr_rts.
But this should not matter as the setup should be called after
uart_change_speed anyway.
Before:                             After:
dtr/rts setup (dtr_rts)             uart_change_speed (startup)
uart_change_speed (update_termios)  dtr/rts setup (dtr_rts)
dtr/rts setup (update_termios)      dtr/rts setup (update_termios)

The second setup will dismiss with the next patch.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The bit is set in tty_port_block_til_ready (via moxa_open) and unset
in tty_port_close (via moxa_close). No need to pin it in the driver.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Devices extracted from device tree all seem to have pdev->id set to -1.
Up until now we mapped all devices with id -1 to the first device.  This
behaviour could lead to problems when using more than one Altera UART in
a system.

This patch changes the behaviour of the driver to scan for the next free
id in case the id is -1.

Because we cannot refer back to the assigned id in altera_uart_remove,
the port instance needs to be stored in device drvdata.
Reported-by: NDavid Smoot <davidsmoot@gmail.com>
Cc: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When tty_add_file fails we omit to clean up. Fix that by calling
tty_release appropriatelly.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Used the newly introduced deinitialize_tty_struct to properly shut
down ldisc.

It is intended to fix the Julian's reported problem. He reports that
kmemleak checker warns about memory leak:
unreferenced object 0xc0e19860 (size 8):
comm cat, pid 1226, jiffies 4294919464 (age 287.476s)
hex dump (first 8 bytes):
44 de 2d c1 01 00 00 00 D.-.....
backtrace:
[<c1065a74>] create_object+0x109/0x1ad
[<c1063d2b>] kmem_cache_alloc+0x60/0x68
[<c113505c>] tty_ldisc_get+0x54/0x76
[<c11358c9>] tty_ldisc_init+0xa/0x20
[<c1130ab4>] initialize_tty_struct+0x2d/0x1ac
[<c1130c8c>] tty_init_dev+0x59/0x10d
[<c113136d>] tty_open+0x24a/0x3a2
...
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Reported-by: NJulian Anastasov <ja@ssi.bg>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Introduce deinitialize_tty_struct which should be called after
initialize_tty_struct and before successfull tty_ldisc_setup.

It calls tty_ldisc_deinit which is opposite of tty_ldisc_init. It only
puts a reference to ldisc and assigns NULL to tty->ldisc.

It will be used to shut down ldisc when tty_release cannot be called
yet.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Change it so that we call the deinit functions at one place at the end
of the function (by gotos). And while at it use some sane label names.

This is a preparation for the deinitialization of tty in the next
patch.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Change it so that we call the deinit functions at one place at the end
of the function (by gotos). And while at it use some sane label names.

This is a preparation for the deinitialization of tty in the next
patch.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Change it so that we call the deinit functions at one place at the end
of the function (by gotos). And while at it use some sane label names.

This is a preparation for the deinitialization of tty in the next
patch.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

drivers/tty/rocket.c:1393:2: warning: Value stored to 'cp' is never read
        cp = &info->channel;
        ^    ~~~~~~~~~~~~~~
drivers/tty/rocket.c:1412:2: warning: Value stored to 'cp' is never read
        cp = &info->channel;
        ^    ~~~~~~~~~~~~~~
drivers/tty/rocket.c:1730:2: warning: Value stored to 'cp' is never read
        cp = &info->channel;
        ^    ~~~~~~~~~~~~~~
drivers/tty/rocket.c:1825:3: warning: Value stored to 'str' is never read
                str = "8";
                ^     ~~~
[many 'str' warnings stripped]
drivers/tty/rocket.c:2037:3: warning: Value stored to 'board_type' is never read
                board_type = "RocketModem";
                ^            ~~~~~~~~~~~~~
[some 'board_type' warnings stripped]
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

drivers/tty/moxa.c:1287:2: warning: Value stored to 'port' is never read
        port = tty->index;
        ^      ~~~~~~~~~~
drivers/tty/moxa.c:1763:2: warning: Value stored to 'cflag' is never read
        cflag = termio->c_cflag;        /* termio->c_cflag */
        ^       ~~~~~~~~~~~~~~~
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

drivers/tty/vt/vt.c:892:2: warning: Value stored to 'old_screen_size' is never read
        old_screen_size = vc->vc_screenbuf_size;
        ^                 ~~~~~~~~~~~~~~~~~~~~~
drivers/tty/vt/vt.c:890:2: warning: Value stored to 'old_cols' is never read
	old_cols = vc->vc_cols;
	^          ~~~~~~~~~~~
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

drivers/tty/cyclades.c:1454:2: warning: Value stored to 'channel' is never read
	channel = info->line - card->first_line;
	^         ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Fix it by moving it to the appropriate debug section where it is used.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

drivers/tty/serial/serial_core.c:1980:2: warning: Value stored to 'tty' is never read
        tty = port->tty;
        ^     ~~~~~~~~~
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Acked-by: NGovindraj.R <govindraj.raja@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

drivers/tty/vt/vt_ioctl.c:1525:2: warning: Value stored to 'kbd' is never read
kbd = kbd_table + console;
^     ~~~~~~~~~~~~~~~~~~~
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Cc: Arthur Taylor <art@ified.ca>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

After adding support for K_OFF in KDSKBMODE, it was forgotten to
add support for returning it in KDGKBMODE.
Signed-off-by: NArthur Taylor <art@ified.ca>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The current check is uneeded, since !retval will always returns true,
as retval returned from tty_add_file is checked earlier and tty_open
exits if it's not zero.
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NHerton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

* 'for-39-rc4' of git://codeaurora.org/quic/kernel/davidb/linux-msm:
  msm: timer: fix missing return value
  msm: Remove extraneous ffa device check

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: xen-kbdfront - fix mouse getting stuck after save/restore
  Input: estimate number of events per packet
  Input: evdev - indicate buffer overrun with SYN_DROPPED
  Input: document event types and codes and their intended use
  Input: add KEY_IMAGES specifically for AL Image Browser
  Input: twl4030_keypad - fix potential NULL dereference in twl4030_kp_probe()
  Input: h3600_ts - fix error handling at connect
  Input: twl4030_keypad - avoid potential NULL-pointer dereference