The interrupt for the corresponding pin is configured to trigger when the
pin state changes compared to a preconfigured state (Bit set in INTCON).
This state is set by setting/clearing the bit in DEFVAL.
In the interrupt handler we need also to check if the bit in INTCON is set
for level triggered interrupts.
Signed-off-by: NAlexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The chip is also an 8 bit shift register which works out of the box as a GPO
expander with this patch
Signed-off-by: NNicolas Saenz Julienne <nicolassaenzj@gmail.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Current code calls irq_domain_alloc_irqs_parent() in .alloc,
so it should call irq_domain_free_irqs_parent() accordingly in .free.
Fix it by switching to use irq_domain_free_irqs_common() instead.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch adds a new ACPI HID, AMDIF030, in the pt_gpio_acpi_match.

Signed-off-by: YD Tseng<Yd_Tseng@asmedia.com.tw>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Use gpio-generic to simplify this driver.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Tested-by: NYD Tseng <Yd_Tseng@asmedia.com.tw>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

When using the GPIOLIB_IRQCHIP the gpiolib provides a
straight-forward implementation of request/release resources,
rely on that instead.

Cc: Phil Reid <preid@electromag.com.au>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This switches the mcp23s08 driver to use the gpiolib irqchip
helpers.
Signed-off-by: NPhil Reid <preid@electromag.com.au>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This allows to set multiple outputs using a single SPI transfer.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NPhil Reid <preid@electromag.com.au>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This allows to set multiple outputs using a single register write.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Set it once is enough, so remove the second platform_set_drvdata() call.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

No need to store *medv in struct men_z127_gpio.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The mcp23s18 is configurable on clearing the interrupt on either reading
INTCAP or GPIO. Since driver reads INTCAP in IRQ and not the GPIO reg need
to set control byte for this mode.
Signed-off-by: NPhil Reid <preid@electromag.com.au>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Fixes: 79a9becd ("gpiolib: export descriptor-based GPIO interface")
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

pca953x_gpio_set_multiple() divides by 4 to convert from longs to bytes,
which assumes a 32-bit platform, and is not correct on 64-bit platforms.
Use "sizeof(...)" instead to fix this.

Cc: stable@vger.kernel.org
Fixes: b4818afe ("gpio: pca953x: Add set_multiple to allow multiple bits to be set in one write.")
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NPhil Reid <preid@electromag.com.au>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The standby GPIO controller can be used as a interrupt controller.
Select GPIOLIB_IRQCHIP when compiling this driver. Otherwise we get
a compilation error:

drivers/gpio/gpio-xgene-sb.c: In function 'xgene_gpio_sb_probe':
drivers/gpio/gpio-xgene-sb.c:312:10: error: 'struct gpio_chip'
  has no member named 'irqdomain'
  priv->gc.irqdomain = priv->irq_domain;
          ^
scripts/Makefile.build:295: recipe for target
'drivers/gpio/gpio-xgene-sb.o' failed
make[2]: *** [drivers/gpio/gpio-xgene-sb.o] Error 1

Fixes: 1013fc41 "gpio: xgene: Enable X-Gene standby GPIO as interrupt controller"
Signed-off-by: NMatthias Brugger <mbrugger@suse.com>
Acked-by: NQuan Nguyen <qnguyen@apm.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add support for the TPS65086 PMIC GPOs.

TPS65086 has four configurable GPOs that can be used for several
purposes. These are output only.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

I screwed up while merging the immutable branch for TPS65912,
so fixing it unbroken again.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: Andrew F. Davis <afd@ti.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This reverts commit 3fab91ea.

GPIO chip structure already has "parent" field which is used for the
same purpose as "dev" field in gpio_bank structure - store pointer on
GPIO device.

Hence, drop duplicated "dev" field from gpio_bank structure.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NSantosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Setting gc->direction_output to gc->direction_output looks strange.
I think this change makes the intention more clear.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

*read_reg and *write_reg can be removed because at all the places to call
them, we can just use gc->read_reg/gc->write_reg instead.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

For devtype with specific gpio_dir_out implementation, current code is
wrong because below code sets both gc->direction_output and
mpc8xxx_gc->direction_output to the same function.

gc->direction_output = devtype->gpio_dir_out ?: gc->direction_output;
mpc8xxx_gc->direction_output = gc->direction_output;

Set mpc8xxx_gc->direction_output = gc->direction_output first to fix it.
This way mpc8xxx_gc->direction_output actually calls the standard
bgpio_dir_out() to update register.

Fixes: commit 42178e2a ("drivers/gpio: Switch gpio-mpc8xxx to use gpio-generic")
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch adds support for the mcp23s18 which is very similar to
the mcp23s17. A couple of control bits are not the same.
Notable IOCON_HAEN (s17 only) & IOCON_INTCC. Which can be ignored.

Patch changes the following:
- Add mcp23s18 types.
- Always set mirror bit if the dts defines mcp23s18. regardless of type.
  Mirror bit is ignored on 8 bit devices anyway.
- In mcp23s08_probe use chip.ngpio instead of logic based on type
  to determine number of gpio lins to increment by. This is set
  appropiately by the call to mcp23s08_probe_one.
- Add mcp23s18 to device tree documentation.
- Remove statement that irqs don't work for spi. They do.
  Tested with mcp23s18.
Signed-off-by: NPhil Reid <preid@electromag.com.au>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The 16Z127 is a 32bit GPIO controller on a MCB FPGA.
Every single line can be configured as input and output.

Push pull and open drain are supported as well as setting
a debounce value for the input lines.
Signed-off-by: NAndreas Werner <andy@wernerandy.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The implementation of lp3943_gpio_request/lp3943_gpio_free test pin_used
for tracing the pin usage. However, gpiolib already checks FLAG_REQUESTED
flag for the same purpose. So remove the redundant implementation.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Replace calls to devm_request_mem_region and devm_ioremap with a
direct call to devm_ioremap_resource instead and modify error
handling.

Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more
clear.

A simplified version of the Coccinelle semantic patch that is used to
make this change is as follows:
//<smpl>
@nm@
expression myname;
identifier i;
@@

struct platform_driver i = { .driver = { .name = myname } };

@@
expression dev,res,size,e1,e;
expression nm.myname;
@@

-if (!devm_request_mem_region(dev, res->start, size,
-                              \(res->name\|dev_name(dev)\|myname\)))
                               {
-   ...
-   return ...;
-}
... when != res->start = e1
e =
-devm_ioremap(dev,res->start,size);
+devm_ioremap_resource(dev,res);

if
-(e == NULL)
+(IS_ERR(e))
{
 ...
-return ...;
+return PTR_ERR(e);
}
//</smpl>

Further, updated error handling by hand as devm_ioremap_resource
gives appropriate error messages, so remove unnecessary error
messages.
Signed-off-by: NAmitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The TS-4800 is an i.MX515 board. Its GPIO driver should only be compiled
for this CPU or for test builds.
Signed-off-by: NJulien Grossholtz <julien.grossholtz@savoirfairelinux.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The original code of gpiodev_add_to_list is not very clear which
lead to bugs or compiling warning, reference the following patches:
Bugs:
1.  Commit ef7c7553 ("gpiolib: improve overlap check of range of
    gpio").
2.  Commit 96098df1 ("gpiolib: fix chip order in gpio list")

Warning:
1.  Commit e28ecca6 ("gpio: fix warning about iterator").
of gpio").

There is a off-list discussion about how to improve it consequently.
This commit try to follow this by rewriting the whole functions.

Tested pass with my gpio mockup driver and test scripts[1].

[1] http://www.spinics.net/lists/linux-gpio/msg09598.htmlSuggested-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NBamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

There is no build dependency for this driver, so enable COMPILE_TEST to get
better build coverage.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

These fields are initialized by bgpio_init() with exactly the same settings
so remove the redundant code.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

I named the field representing the current user of GPIO line as
"label" but this is too vague and ambiguous. Before anyone gets
confused, rename it to "consumer" and indicate clearly in the
documentation that this is a string set by the user of the line.

Also clean up leftovers in the documentation.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

We started to assign the gpio_device as parent for the sysfs
but this changes the expected layout of sysfs. Restore the
previous behaviour.
Signed-off-by: NBamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

There is no build dependency for this driver, so enable COMPILE_TEST to get
better build coverage.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The R-Car GPIO driver handles Runtime PM for requested GPIOs only.

When using a GPIO purely as an interrupt source, no Runtime PM handling
is done, and the GPIO module's clock may not be enabled.

To fix this:
  - Add .irq_request_resources() and .irq_release_resources() callbacks
    to handle Runtime PM when an interrupt is requested,
  - Add irq_bus_lock() and sync_unlock() callbacks to handle Runtime PM
    when e.g. disabling/enabling an interrupt, or configuring the
    interrupt type.

Fixes: d5c3d846 "net: phy: Avoid polling PHY with PHY_IGNORE_INTERRUPTS"
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This driver has .can_sleep flag set.
So the pisosr_gpio_get() can be called from contexts that can sleep.
Thus use the cansleep() variant in pisosr_gpio_refresh().
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

gpio->load_gpio is optional, so use devm_gpiod_get_optional instead.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

ret variable can contain error values and is compared with zero.
Its type must be signed.

The problem has been detected using coccinelle script
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.

This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>