Due to the use of a _REQ_DIRECT_PROBE bit, which is
unnecessary (and I wonder why it was done that way),
an interesting situation can arise:
 1) we try to probe an access point
 2) the AP doesn't response in time
 3) we tell userspace that we gave up
 4) the AP suddenly responds
 5) we auth/assoc with the AP

I've seen 4) happen in testing with hostapd SIGSTOPped,
and when SIGCONTinued it processes the probe requests
that came in and send responses. But 5) is not supposed
to happen after we tell everybody we've given up on the
AP.

To fix this, remove the _REQ_DIRECT_PROBE request bit,
and process probe responses when we're in the relevant
MLME state, namely IEEE80211_STA_MLME_DIRECT_PROBE.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If the direct probe times out, we need to send the authentication
timeout event to notify SME in the same way as we notify on timeout
with authentication frames since the direct probe is run as part of
the authentication attempt.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order to later add tracing or verifications to the driver
calls mac80211 makes, this patch adds static inline wrappers
for all operations.

All calls are now written as

	drv_<op>(local, ...);

instead of

	local->ops-><op>(&local->hw, ...);

Where necessary, the wrappers also do existence checking and
return default values as appropriate.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The config_interface method is a little strange, it contains the
BSSID and beacon updates, while bss_info_changed contains most
other BSS information for each interface. This patch removes
config_interface and rolls all the information it previously
passed to drivers into bss_info_changed.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We currently have two beacon interval configuration knobs:
hw.conf.beacon_int and vif.bss_info.beacon_int. This is
rather confusing, even though the former is used when we
beacon ourselves and the latter when we are associated to
an AP.

This just deprecates the hw.conf.beacon_int setting in favour
of always using vif.bss_info.beacon_int. Since it touches all
the beaconing IBSS code anyway, we can also add support for
the cfg80211 IBSS beacon interval configuration easily.

NOTE: The hw.conf.beacon_int setting is retained for now due
      to drivers still using it -- I couldn't untangle all
      drivers, some are updated in this patch.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are some places marked
	/* XXX maybe racy? */
and they really are racy because there's no locking.

This patch reworks much of the scan code, and introduces proper
locking for the scan request as well as the internal scanning
(which is necessary for IBSS/managed modes). Helper functions
are added to call the scanning code whenever necessary. The
scan deferring is changed to simply queue the scanning work
instead of trying to start the scan in place, the scanning work
will then take care of the rest.

Also, currently when internal scans are requested for an interface
that is trying to associate, we reject such scans. This was not
intended, the mlme code has provisions to scan twice when it can't
find the BSS to associate with right away; this has never worked
properly. Fix this by not rejecting internal scan requests for an
interface that is associating.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Kalle points out that max_sleep_interval is somewhat confusing
because the value is measured in beacon intervals, and not in
TU. Rename it to max_sleep_period to be consistent with things
like DTIM period that are also measured in beacon intervals.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When somebody changes the PS parameters while scanning
is in progress, we enable PS -- during the scan. This
is clearly not desirable, and we can just abort enabling
PS when scanning since when the scan finishes it will
be taken care of.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Reviewed-by: NKalle Valo <kalle.valo@iki.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

SME needs to be notified when the authentication or association
attempt times out and MLME has stopped processing in order to allow
the SME to decide what to do next.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The maximum sleep interval, for powersave purposes, is
determined by the DTIM period (it may not be larger)
and the required networking latency (it must be small
enough to fulfil those constraints).

This makes mac80211 calculate the maximum sleep interval
based on those constraints, and pass it to the driver.
Then the driver should instruct the device to sleep at
most that long.

Note that the device is responsible for aligning the
maximum sleep interval between DTIMs, we make sure it's
not longer but it needs to make sure it's between them.

Also, group some powersave documentation together and
make it more explicit that we support managed mode only,
and no IBSS powersaving (yet).
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Stephen Rothwell reported these warnings from a 32-bit build:

  net/mac80211/mlme.c:1771: warning: left shift count >= width of type
  net/mac80211/mlme.c:1772: warning: left shift count >= width of type
  net/mac80211/mlme.c:1773: warning: left shift count >= width of type
  net/mac80211/mlme.c:1774: warning: left shift count >= width of type
  net/mac80211/mlme.c:1775: warning: left shift count >= width of type

This shows a bug in my code -- BIT(X) uses just "1 << X" which means
a 32-bit integer on 32-bit platforms, but the code here needs a u64
on all platforms. Fix this by using "1ULL << X" instead of BIT(X).

Thanks Stephen!
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The TIM IE must not be shorter than 4 bytes, so verify that
when parsing it and use the proper type. To ease that adjust
struct ieee80211_tim_ie to have a virtual bitmap of size
at least 1.

Also check that the TIM IE is actually present before trying
to parse it!

Because other people may need the function, make it a static
inline in ieee80211.h.

(The original "mac80211: validate TIM IE length" was a minimal fix for
2.6.30.  This purports to be the full, correct fix. -- JWL)
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since we have ->deauth and ->disassoc we can support the
wext SIWMLME call directly without driver wext handlers.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable PS by default (depending on Kconfig) -- rely on drivers
to control the level using pm_qos. Due to the previous patch
we turn off PS when necessary due to latency requirements.

This has a Kconfig symbol so people can, if they really want,
configure the default in their kernels. We may want to keep it
at "default y" only in wireless-testing for a while.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Regardless of whether the hardware implements beacon filtering,
there's no need to process all beacons in software all the time
throughout the stack (mac80211 does a lot, then cfg80211, then
in the future possibly userspace).

This patch implements the "best possible" beacon filtering in
mac80211. "Best possible" means that it can look for changes in
all requested information elements, and distinguish vendor IEs
by their OUI.

In the future, we will add nl80211 API for userspace to request
information elements and vendor IE OUIs to watch -- drivers can
then implement the best they can do while software implements
it fully.

It is unclear whether or not this actually saves CPU time, but
the data is all in the cache already so it should be fairly
cheap. The additional _testing_, however, has great benefit;
Without this, and on hardware that doesn't implement beacon
filtering, wrong assumptions about, for example, scan result
updates could quickly creep into code.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When an application asks for a latency lower than the beacon interval
there's nothing we can do -- we need to stay awake and not have the
AP buffer frames for us. Add code to automatically calculate this
constraint in mac80211 so drivers need not concern themselves with it.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When you have multiple virtual interfaces the current
implementation requires setting them up properly from
userspace, which is undesirable when we want to default
to power save mode. Keep track of powersave requested
from userspace per managed mode interface, and only
enable powersave globally when exactly one managed mode
interface is active and has powersave turned on.

Second, only start the dynPS timer when PS is turned
on, and properly turn it off when PS is turned off.

Third, fix the scan_sdata abuse in the dynps code.

Finally, also reorder the code and refactor the code
that enables PS or the dynps timer instead of having
it copied in two places.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When using nl80211 association, we need to send association response
with a failure code to user space SME instead of just internally
trying to send out the same (re)association request again couple of
times. This fixes problems in association process getting stuck on a
failure when user space is not notified in any way that something
actually failed.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It really belongs into that file since it is only relevant
for managed mode. Move 1:1, not even whitespace changes,
but make it static and remove from header file.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Previously, nl80211 mlme events were generated only for received
deauthentication and disassociation frames. We need to do the same for
locally generated ones in order to let applications know that we
disconnected (e.g., when AP does not reply to a probe). Rename the
nl80211 and cfg80211 functions (s/rx_//) to make it clearer that they
are used for both received and locally generated frames.
Signed-off-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"mac80211: fix basic rates setting from association response"
introduced a copy/paste error.

Unfortunately, this not just leads to wrong data being passed
to the driver but is remotely exploitable for some hardware or
driver combinations.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.29]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently beacon loss detection triggers after a scan. A probe request
is sent and a message like this is printed to the log:

wlan0: beacon loss from AP 00:12:17:e7:98:de - sending probe request

But in fact there is no beacon loss, the beacons are just not received
because of the ongoing scan. Fix it by updating last_beacon after
the scan has finished.
Reported-by: NJaswinder Singh Rajput <jaswinder@kernel.org>
Signed-off-by: NKalle Valo <kalle.valo@iki.fi>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The TIM IE must not be shorter than 4 bytes, so verify that
when parsing it.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using the scan_sdata variable here is terribly wrong,
if there has never been a scan then we fail. However,
we need a bandaid...
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.29]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On Sunday 05 April 2009 11:29:38 Michael Buesch wrote:
> On Sunday 05 April 2009 11:23:59 Jaswinder Singh Rajput wrote:
> > With latest linus tree I am getting, .config file attached:
> >
> > [   22.895051] r8169: eth0: link down
> > [   22.897564] ADDRCONF(NETDEV_UP): eth0: link is not ready
> > [   22.928047] ADDRCONF(NETDEV_UP): wlan0: link is not ready
> > [   22.982292] libvirtd used greatest stack depth: 4200 bytes left
> > [   63.709879] wlan0: authenticate with AP 00:11:95:9e:df:f6
> > [   63.712096] wlan0: authenticated
> > [   63.712127] wlan0: associate with AP 00:11:95:9e:df:f6
> > [   63.726831] wlan0: RX AssocResp from 00:11:95:9e:df:f6 (capab=0x471 status=0 aid=1)
> > [   63.726855] wlan0: associated
> > [   63.730093] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
> > [   74.296087] wlan0: no IPv6 routers present
> > [   79.349044] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [  119.358200] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [  179.354292] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [  259.366044] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [  359.348292] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [  361.953459] packagekitd used greatest stack depth: 4160 bytes left
> > [  478.824258] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [  598.813343] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [  718.817292] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [  838.824567] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [  958.815402] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1078.848434] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1198.822913] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1318.824931] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1438.814157] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1558.827336] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1678.823011] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1798.830589] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1918.828044] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 2038.827224] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 2116.517152] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 2158.840243] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 2278.827427] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
>
>
> I think this message should only show if CONFIG_MAC80211_VERBOSE_DEBUG is set.
> It's kind of expected that we lose a beacon once in a while, so we shouldn't print
> verbose messages to the kernel log (even if they are KERN_DEBUG).
>
> And besides that, I think one can easily remotely trigger this message and flood the logs.
> So it should probably _also_ be ratelimited.

Something like this:
Signed-off-by: NMichael Buesch <mb@bu3sch.de>

Add IEEE80211_HW_BEACON_FILTERING flag so that driver inform that it supports
beacon filtering. Drivers need to call the new function
ieee80211_beacon_loss() to notify about beacon loss.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Separate beacon and rx path tracking in preparation for the beacon filtering
support. At the same time change ieee80211_associated() to look a bit simpler.

Probe requests are now sent only after IEEE80211_PROBE_IDLE_TIME, which
is now set to 60 seconds.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently the timer is triggering every two seconds
(IEEE80211_MONITORING_INTERVAL). Decrease the timer to only trigger during
data idle periods to avoid waking up CPU unnecessary. The timer will
still trigger during idle periods, that needs to be fixed later.

There's also a functional change that probe requests are sent only when the
data path is idle, earlier they were sent also while there was activity
on the data path.

This is also preparation for the beacon filtering support. Thanks to
Johannes Berg for the idea.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Neither can currently be set from userspace, so there's no
regression potential, and neither will be supported from
userspace since the new userspace APIs allow the SME, which
is in userspace, to control all we need.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The functionality that NL80211_CMD_SET_MGMT_EXTRA_IE provided can now
be achieved with cleaner design by adding IE(s) into
NL80211_CMD_TRIGGER_SCAN, NL80211_CMD_AUTHENTICATE,
NL80211_CMD_ASSOCIATE, NL80211_CMD_DEAUTHENTICATE, and
NL80211_CMD_DISASSOCIATE.

Since this is a very recently added command and there are no known (or
known planned) applications using NL80211_CMD_SET_MGMT_EXTRA_IE and
taken into account how much extra complexity it adds to the IE
processing we have now (and need to add in the future to fix IE order
in couple of frames), it looks like the best option is to just remove
the implementation of this command for now. The enum values themselves
are left to avoid changing the nl80211 command or attribute numbers.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds new nl80211 commands to allow user space to request
authentication and association (and also deauthentication and
disassociation). The commands are structured to allow separate
authentication and association steps, i.e., the interface between
kernel and user space is similar to the MLME SAP interface in IEEE
802.11 standard and an user space application takes the role of the
SME.

The patch introduces MLME-AUTHENTICATE.request,
MLME-{,RE}ASSOCIATE.request, MLME-DEAUTHENTICATE.request, and
MLME-DISASSOCIATE.request primitives. The authentication and
association commands request the actual operations in two steps
(assuming the driver supports this; if not, separate authentication
step is skipped; this could end up being a separate "connect"
command).

The initial implementation for mac80211 uses the current
net/mac80211/mlme.c for actual sending and processing of management
frames and the new nl80211 commands will just stop the current state
machine from moving automatically from authentication to association.
Future cleanup may move more of the MLME operations into cfg80211.

The goal of this design is to provide more control of authentication and
association process to user space without having to move the full MLME
implementation. This should be enough to allow IEEE 802.11r FT protocol
and 802.11s SAE authentication to be implemented. Obviously, this will
also bring the extra benefit of not having to use WEXT for association
requests with mac80211. An example implementation of a user space SME
using the new nl80211 commands is available for wpa_supplicant.

This patch is enough to get IEEE 802.11r FT protocol working with
over-the-air mechanism (over-the-DS will need additional MLME
primitives for handling the FT Action frames).
Signed-off-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add new nl80211 event notifications (and a new multicast group, "mlme")
for informing user space about received and processed Authentication,
(Re)Association Response, Deauthentication, and Disassociation frames in
station and IBSS modes (i.e., MLME SAP interface primitives
MLME-AUTHENTICATE.confirm, MLME-ASSOCIATE.confirm,
MLME-REASSOCIATE.confirm, MLME-DEAUTHENTICATE.indicate, and
MLME-DISASSOCIATE.indication). The event data is encapsulated as the 802.11
management frame since we already have the frame in that format and it
includes all the needed information.

This is the initial step in providing MLME SAP interface for
authentication and association with nl80211. In other words, kernel code
will act as the MLME and a user space application can control it as the
SME.
Signed-off-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We must not clear the previous BSSID when roaming to another AP within
the same ESS for reassociation to be used properly. It is fine to
clear this when the SSID changes, so let's move the code into
ieee80211_sta_set_ssid().
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If a scan is queued in STA mode while the interface is in state direct
probe, authenticate or associate the scan is delayed until the interface
enters disabled or associated state. But in case of direct probe-,
authentication- or association- timeout sta_work will not be scheduled
anymore (without external trigger) and thus the pending scan is not
executed and prevents a new scan from being triggered (-EBUSY).

Fix this by queueing the sta work again after direct probe-, authentication-
and association- timeout.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This inline is useless and actually makes the code _longer_
rather than shorter.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If cfg80211 requests a scan it awaits either a return code != 0 from
the scan function or the cfg80211_scan_done to be called. In case of
a STA mac80211's scan function ever returns 0 and queues the scan request.
If ieee80211_sta_work is executed and ieee80211_start_scan fails for
some reason cfg80211_scan_done will never be called but cfg80211 still
thinks the scan was triggered successfully and will refuse any future
scan requests due to drv->scan_req not being cleaned up.

If a scan is triggered from within the MLME a similar problem appears. If
ieee80211_start_scan returns an error, local->scan_req will not be reset
and mac80211 will refuse any future scan requests.

Hence, in both cases call ieee80211_scan_failed (which notifies cfg80211
and resets local->scan_req) if ieee80211_start_scan returns an error.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Incorrect local->wmm_acm bits were set for AC_BK and AC_BE. Fix this
and add some comments to make it easier to understand the AC-to-UP(pair)
mapping. Set the wmm_acm bits (and show WMM debug) even if the driver
does not implement conf_tx() handler.

In addition, fix the ACM-based AC downgrade code to not use the
highest priority in error cases. We need to break the loop to get the
correct AC_BK value (3) instead of returning 0 (which would indicate
AC_VO). The comment here was not really very useful either, so let's
provide somewhat more helpful description of the situation.

Since it is very unlikely that the ACM flag would be set for AC_BK and
AC_BE, these bugs are not likely to be seen in real life networks.
Anyway, better do these things correctly should someone really use
silly AP configuration (and to pass some functionality tests, too).

Remove the TODO comment about handling ACM. Downgrading AC is
perfectly valid mechanism for ACM. Eventually, we may add support for
WMM-AC and send a request for a TS, but anyway, that functionality
won't be here at the location of this TODO comment.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If the AP thinks we are in power save state eventhough we are not truly
in that state, it sets the TIM bit and does not send a data frame unless
we send a null data frame to correct the state in the AP.
This might happen if the null data frame for wake up is lost in the air
after we disable power save.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no need to parse the AP's HT capabilities if
the STA uses TKIP/WEP cipher. This allows the rate control
module to choose the correct(legacy) rate table.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>