- 03 6月, 2015 3 次提交
-
-
由 Hans de Goede 提交于
The Mele A1000G-quad and the Mele M9 have the same PCB, sofar we've been using the same dts for both models. Unfortunately this does not work for the otg controller, on the M9 this is routed to a micro-usb connector on the outside, while as on the A1000G-quad it is connected to an usb to sata bridge (which is not populated on the M9 pcb). This commit adds a new dts for the Mele-A1000G-quad to allow using different otg controller settings on the 2 boards. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Hans de Goede 提交于
The ga10h is an 10" tablet with an A33 or A23 soc, 1G RAM, 8G or 16G nand, sdio wifi, 2 micro usb ports, 1 otg and 1 host and 1 micro sd slot. This commit adds a dts file for the v1.1 pcb with an a33 soc. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Chen-Yu Tsai 提交于
The SinA33 is a core/SDK development board by Sinlinx. The core board does not have any connectors or pads, other than the pads used to connect it to the SDK board. The core board only has the A33 SoC, 2 RAM chips, an eMMC flash chip, the AXP223 PMIC, and supporting discrete components. eMMC is optional. The SDK board has a USB host, USB OTG, volume control and home buttons, audio input/output jacks, a micro-SD slot, camera and SDIO expansion headers, an LCD connector, and a GPIO expansion header, which has UARTs, MIPI DSI and I2C available. Only UART0 is enabled though. Signed-off-by: NChen-Yu Tsai <wens@csie.org> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
- 02 6月, 2015 1 次提交
-
-
由 Vishnu Patekar 提交于
ET-Q8_A33 is A33 based cheap tablet in common Q8 format. It has 512MB RAM, 4GB Nand, 7" Display, RDA5900P wifi, GSL1680 touch, etc. Signed-off-by: NVishnu Patekar <vishnupatekar0510@gmail.com> Signed-off-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com> Tested-by: NChen-Yu Tsai <wens@csie.org>
-
- 01 6月, 2015 1 次提交
-
-
由 Maxime Ripard 提交于
The A23 Evaluation Board has an MMC slot, two UARTs, NAND, a few display connectors (RGB, MIPI, LVDS), a mini-PCIE slot, USB host and OTG and a bunch of embedded sensors. Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
- 30 4月, 2015 1 次提交
-
-
由 Marcus Cooper 提交于
The MK808C is an A20 based android stick, with 1G RAM, 8G NAND flash, a RTL8723au wifi + bt combo chip, a USB host ports using USB-A receptacles, a mini USB-B receptacle for USB OTG, mini HDMI and a TRS connector for AV. This patch adds basic support for the device, more information can be found here (http://linux-sunxi.org/MK808C). Signed-off-by: NMarcus Cooper <codekipper@gmail.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
- 27 4月, 2015 10 次提交
-
-
由 Hans de Goede 提交于
The Jesurun Q5 has a black plastic casing with the approximate dimensions of 100mm x 100mm x 24mm with rounded edges. In terms of hardware it features an Allwinner A10 SoC with 1GB RAM and 8GB of NAND flash. The external connectors are: 2x USB-A female supporting USB2.0, 3.5mm female jack for audio, HDMI female, SPDIF, RJ45 LAN and Power. In addition the device has 1x red LED (hard wired to power) and an programmable green led. On the board there is also an unpopulated IR receiver and the UART. The devices is equipped with an AXP209 PMU. For more details see: http://linux-sunxi.org/Jesurun_Q5Signed-off-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Hans de Goede 提交于
The Orangepi mini is a development board using the Allwinner A20 SoC, with 1G RAM, 2 microsd slots (use the top side one for booting), HDMI, 1Gbit ethernet, USB wifi, Micro USB (otg), sata, 4 USB A ports, ir receiver and a headphones jack. Also see: http://linux-sunxi.org/Xunlong_Orange_Pi_Mini http://www.orangepi.org/Signed-off-by: NHans de Goede <hdegoede@redhat.com> [maxime: Added /chosen/stdout-path] Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Hans de Goede 提交于
The Orangepi is a development board using the Allwinner A20 SoC, with 1G RAM, microsd slot, HDMI, 1Gbit ethernet, USB wifi, Micro USB (otg), sata, 4 USB A ports, ir receiver and a headphones jack. Also see: http://linux-sunxi.org/Xunlong_Orange_Pi http://www.orangepi.org/Signed-off-by: NHans de Goede <hdegoede@redhat.com> [maxime: Added /chosen/stdout-path] Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Tyler Baker 提交于
Add a Cubietech Cubieboard4 device tree and instruct make to build it. This device tree has been derived from the sun9i-a80-optimus.dts as they are very similar in design[1]. Notably, I2C3 is not used on Cubieboard4 and the LED/PWM definitions will need to be updated in the future. [1] http://dl.cubieboard.org/model/cc-a80/Hardware/CC-A80-HW-V1.1.pdfSigned-off-by: NTyler Baker <tyler.baker@linaro.org> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Aleksei Mamlin 提交于
This patch add support for Wexler TAB7200 tablet. The Wexler TAB7200 is a A20 based tablet with 7 inch display(800x480), capacitive touchscreen(5 fingers), 1G RAM, 4G NAND, micro SD card slot, mini HDMI port, 3.5mm audio plug, 1 USB OTG port and 1 USB 2.0 port. Signed-off-by: NAleksei Mamlin <mamlinav@gmail.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Hans de Goede 提交于
The UTOO P66 is a 6" A13 tablet / lcd ereader. It features a 6" 480x800 ips lcd screen, 512MB RAM & 4GB emmc. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Hans de Goede 提交于
The auxtek-t004: http://www.fasttech.com/products/1110/10004200/1318603-auxtek-t004-allwinner-a10s-single-core-android-ics Is an Allwinner A10s based hdmi tv stick with with 512M RAM, 4G nand flash, toc9002 (bcm43362) sdio wifi, 1 USB host ports using an USB-A receptacle and a 2 micro-usb receptacles, one for power and one for USB OTG. The sdio wifi appears to not have an oob irq hooked up, so we rely on sdio-irq support for it. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Marcus Cooper 提交于
The Mele I7 is a Allwinner A31 based Android TV box, with 1G RAM, 8GB NAND flash, a RTL8188etv wifi chip, 3 USB Host ports using USB-A receptacles, a micro USB-B receptacle for USB OTG, HDMI out, a TRS connector for A/V, SPDIF and IrDA. This patch adds basic support for the device, more information can be found here (http://linux-sunxi.org/Mele_I7). Signed-off-by: NMarcus Cooper <codekipper@gmail.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Adam Sampson 提交于
Add support for the LinkSprite pcDuino 3 Nano board. This is a low-cost Allwinner A20 board with Arduino-style GPIO headers; it features 1G RAM, 4G NAND flash, 1 micro-SD, 2 USB sockets, 1 micro USB socket for OTG and another for power in, HDMI, SATA, 5V power for SATA devices, gigabit Ethernet, an IR receiver, 3.5mm audio out and a MIPI camera connector. For more details, see: http://linux-sunxi.org/LinkSprite_pcDuino3_Nano Changes in v3: - rename LEDs to pcduino3-nano:green:usr[12] - remove optional features on Arduino headers (i2c2, spi0, uart2) Signed-off-by: NAdam Sampson <ats@offog.org> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Priit Laes 提交于
Gemei G9 is an A10 based tablet, with 1G RAM, 16G NAND, 1024x768 IPS LCD display, stereo speakers, 1.3MP front camera and 5 MP rear camera, 8000mAh battery, GT901 2+1 touchscreen, Bosch BMA250 accelerometer and RTL8188CUS USB wifi. It also has MicroSD slot, miniHDMI, 1 x MicroUSB OTG port and 1 x MicroUSB host port and 3.5mm headphone jack. Changes since v2: * Fix syntax error (brown paper bag release) Changes since v1: * Added sun4i-lradc keymap * Added TODO note about missing IRQ pins for bma250 * Fixed formatting issues and removed external URLs Signed-off-by: NPriit Laes <plaes@plaes.org> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
- 02 4月, 2015 1 次提交
-
-
由 Olof Johansson 提交于
File uses dash in the filename, not underscore. Reported-by: NRussell King <linux@arm.linux.org.uk> Signed-off-by: NOlof Johansson <olof@lixom.net>
-
- 30 3月, 2015 3 次提交
-
-
由 Otavio Salvador 提交于
The WaRP Board is a Wearable Reference Plaform. The board features: - Freescale i.MX6 SoloLite processor with 512MB of RAM - Freescale FXOS8700CQ 6-axis Xtrinsic sensor - Freescale Kinetis KL16 MCU - Freescale Xtrinsic MMA955xL intelligent motion sensing platform The board implements a hybrid architecture to address the evolving needs of the wearables market. The platform consists of a main board and an example daughtercard with the ability to add additional daughtercards for different usage models. For more information about the project, visit: http://www.warpboard.org/Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Peter Chen 提交于
Since imx6sx-sdb reva board is experimental and will not be used formally (eg, no software release based on it), we set revb board as the formal imx6sx-sdb board. The imx6sx-sdb uses pfuse200 as pmic which has only one power supply for both VDDARM_IN and VDDSOC_IN, so VDDARM_IN and VDDSOC_IN have to use the same (higher one in the same frequency) one as its power supply, that's the reason we override the OPP setting in board dts file. Signed-off-by: NPeter Chen <peter.chen@freescale.com> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Peter Chen 提交于
The imx6sx sdb board has two revisions, the current mainline one is reva which is experimental and mainly for internal use. In this commit, we rename imx6sx-sdb.dts to imx6sx-sdb.dtsi, and move the reva dedicated contents to imx6sx-sdb-reva.dts. Signed-off-by: NPeter Chen <peter.chen@freescale.com> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
- 24 3月, 2015 1 次提交
-
-
由 Tomeu Vizoso 提交于
It's commercial name is HP Chromebook 14 and is substantially similar to the Acer Chromebook 13 (nyan-big). Signed-off-by: NTomeu Vizoso <tomeu.vizoso@collabora.com> Acked-by: NStephen Warren <swarren@nvidia.com> Reviewed-by: NAlexandre Courbot <acourbot@nvidia.com> Signed-off-by: NThierry Reding <treding@nvidia.com>
-
- 17 3月, 2015 3 次提交
-
-
由 H. Nikolaus Schaller 提交于
Added Pandora 1 GHz model which is based on Classic/Rebirth with following changes: - upgraded cpu to dm3730 runs on 1GHz - 512 MiB DDR-333 SDRAM @ 200 MHz Signed-off-by: NH. Nikolaus Schaller <hns@goldelico.com> Tested-by: NGrazvydas Ignotas <notasas@gmail.com> Reviewed-by: NGrazvydas Ignotas <notasas@gmail.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 H. Nikolaus Schaller 提交于
Added Pandora Rebirth model which is based on Pandora Classic with 512 MiB DDR-333 SDRAM memory. Signed-off-by: NH. Nikolaus Schaller <hns@goldelico.com> Tested-by: NGrazvydas Ignotas <notasas@gmail.com> Reviewed-by: NGrazvydas Ignotas <notasas@gmail.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Rostislav Lisovy 提交于
Chiliboard uses ChiliSOM as its base. Hardware specification: * ChiliSOM (am335x, PMIC, DRAM, NAND) * Ethernet PHY (id 0) * USB host (usb1) * microSD slot * 2x GPIO LED Signed-off-by: NRostislav Lisovy <lisovy@jablotron.cz> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 16 3月, 2015 1 次提交
-
-
由 Tsahee Zidenberg 提交于
This patch introduces devicetree for the Alpine platform, and for a development board based on the same platform. Signed-off-by: NBarak Wasserstrom <barak@annapurnalabs.com> Signed-off-by: NTsahee Zidenberg <tsahee@annapurnalabs.com> Acked-by: NArnd Bergmann <arnd@arndb.de> Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
- 12 3月, 2015 1 次提交
-
-
由 Simon Guinot 提交于
This patch adds the DT description for the LaCie "2Big NAS" (nas2big). This NAS is an hardware upgrade of the 2Big Network v2. Chipset and device list: - CPU Marvell 88F6282 1600Mhz - SDRAM memory, 256MB DDR3 (2x128MB x8) 533Mhz - 1 Ethernet Gigabit port (PHY Marvell 88E1518) - Flash memory, NAND 256MB TSOP48 - I2C EEPROM, 512 bytes (AT24 type) - PCIe SATA controller JMicron JMB360 (eSATA) - I2C fan controller GMT G762 (with a separate alarm GPIO) - 1 USB2 host port - 1 push button - 1 power switch - 2 SATA LEDs (bi-color, blue and red) - 1 power LED (bi-color, blue and red) - CPLD for LEDs and start-up management (Altera Max EMP3064) Signed-off-by: NSimon Guinot <simon.guinot@sequanux.org> Acked-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
-
- 07 3月, 2015 1 次提交
-
-
由 Rafał Miłecki 提交于
Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Reported-by: NIan Kent <raven@themaw.net> Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
-
- 05 3月, 2015 1 次提交
-
-
由 Josh Wu 提交于
Add at91 sama5d4 xplained board support. Signed-off-by: NJosh Wu <josh.wu@atmel.com> Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
- 04 3月, 2015 1 次提交
-
-
由 Thomas Petazzoni 提交于
This commit adds the Device Tree files for the Armada 39x family of processors, as well as one Armada 398 Development Board. Like for other Marvell EBU families, a common armada-39x.dtsi contains the description of the common features of all Armada 39x SoCs, while armada-390.dtsi and armada-398.dtsi respectively describe the specificities of those SoCs. Finally, an armada-398-db.dts file is added to describe the Armada 398 Development Board itself. So far, the following features are supported: * SMP: dual Cortex-A9 * Basic ARM IPs: SCU, timer, GIC, L2 cache * Basic Marvell IPs: pin-muxing, clocks, system controller, MBus controller, MPIC interrupt controller, timer, CPU reset for SMP, PMSU. * I2C * SPI * SDHCI * XOR * NAND * UART * PCIe Additional features will be supported in the future. Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
-
- 03 3月, 2015 1 次提交
-
-
由 Jonathan Richardson 提交于
DT file to enable the Wireless Audio reference design based on the BCM58305. Reviewed-by: NRay Jui <rjui@broadcom.com> Reviewed-by: NScott Branden <sbranden@broadcom.com> Tested-by: NScott Branden <sbranden@broadcom.com> Signed-off-by: NJonathan Richardson <jonathar@broadcom.com> Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
-
- 02 3月, 2015 1 次提交
-
-
由 Beniamino Galvani 提交于
Add a DTS file for MINIX NEO-X8, a Meson8-based digital media player. Signed-off-by: NBeniamino Galvani <b.galvani@gmail.com> Signed-off-by: NCarlo Caione <carlo@endlessm.com>
-
- 01 3月, 2015 1 次提交
-
-
由 Ulrich Hecht 提交于
Adds config option and enables DTB building. Signed-off-by: NUlrich Hecht <ulrich.hecht+renesas@gmail.com> Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
- 27 2月, 2015 1 次提交
-
-
由 Imre Kaloz 提交于
The Linksys WRT1900AC (Mamba) is a router that has - 2 mini-PCIe slots with Marvell 88W8864 radios - 1 USB 3.0 port - 1 USB 2.0/eSATAp port - 2 Ethernet interfaces connected to a 88E6172 switch (1x WAN + 4x LAN) - 128MB NAND flash - 256MB RAM gregory.clement@free-electrons.com: - add ARM to the title - fix the reference to CONFIG_DEBUG_MVEBU_UART0_ALTERNATE - fix the unbalanced comment for the syscfg partition Signed-off-by: NImre Kaloz <kaloz@openwrt.org> Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
-
- 24 2月, 2015 5 次提交
-
-
由 Simon Horman 提交于
Now that the sh73a0 generic multiplatform case has the same feature set as the kzm9g DT reference board code, we get rid of the latter. DT reference code in the future shall make use of the sh73a0 multiplatform support code with the generic SoC machine vector. Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Magnus Damm 提交于
Build the sh73a0 KZM9G board DTB in case of Multiplatform. The DT reference case will be removed in the future and can be ignored for now. Signed-off-by: NMagnus Damm <damm+renesas@opensource.se> Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Magnus Damm 提交于
Remove the DTS file for the no longer supported Mackerel board. Signed-off-by: NMagnus Damm <damm+renesas@opensource.se> Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Simon Horman 提交于
This removes the remains of the legacy ape6evm platform. Signed-off-by: NUlrich Hecht <ulrich.hecht+renesas@gmail.com> Acked-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Ulrich Hecht 提交于
Now that the r8a73a4 generic multiplatform case has the same features as the APE6EVM DT reference board code, we get rid of the latter. DT reference code in the future shall make use of the r8a73a4 multiplatform support code with the generic SoC machine vector. Signed-off-by: NUlrich Hecht <ulrich.hecht+renesas@gmail.com> Acked-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> [geert: Update Documentation/devicetree/bindings/arm/shmobile.txt] Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
- 30 1月, 2015 1 次提交
-
-
由 Baruch Siach 提交于
cx92755.dtsi describes CX92755 on chip peripherals. cx92755_equinox.dts describes the Equinox evaluation board for the CX92755 SoC. Acked-by: NArnd Bergmann <arnd@arndb.de> Signed-off-by: NBaruch Siach <baruch@tkos.co.il> Signed-off-by: NOlof Johansson <olof@lixom.net>
-
- 27 1月, 2015 1 次提交
-
-
由 Nicolas Ferre 提交于
The entries are separated as ARM V4/V5 and ARM V7 as some other per-SoC config options may be removed in the near future. Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: NOlof Johansson <olof@lixom.net>
-