For whatever reason we only unmask and enable the master error
interrut on gen4. With the EIR handling fixed let's do that
on gen2/3 as well.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611200258.27121-4-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Adjust the EIR clearing to cope with the edge triggered IIR
on i965/g4x. To guarantee an edge in the ISR master error bit
we temporarily mask everything in EMR. As some of the EIR bits
can't even be directly cleared we also borrow a trick from
i915_clear_error_registers() and permanently mask any bit that
remains high. No real thought given to how we might unmask them
again once the cause for the error has been clered. I suppose
on pre-g4x GPU reset will reinitialize EMR from scratch.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611200258.27121-3-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Just like with PIPESTAT, the edge triggered IIR on i965/g4x
also causes problems for hotplug interrupts. To make sure
we don't get the IIR port interrupt bit stuck low with the
ISR bit high we must force an edge in ISR. Unfortunately
we can't borrow the PIPESTAT trick and toggle the enable
bits in PORT_HOTPLUG_EN as that act itself generates hotplug
interrupts. Instead we just have to loop until we've cleared
PORT_HOTPLUG_STAT, or we just give up and WARN.

v2: Don't frob with PORT_HOTPLUG_EN

Cc: stable@vger.kernel.org
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614175625.1615-1-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

For a ppgtt that we are constructing, there is no struct_mutex
dependence so skip it. In the process, also ping the scheduler
frequently to try and avoid the NMI watchdog.

v2: gen6 requires struct_mutex to clean up (currently)
Suggested-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=107094Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180703135331.12265-1-chris@chris-wilson.co.uk

live_gtt is a very slow test to run, simply because it tries to allocate
and use as much as the 48b address space as possibly can and in the
process will try to own all of the system memory. This leads to resource
exhaustion and CPU starvation; the latter impacts us when the NMI
watchdog declares a task hung due to a mutex contention with ourselves.
This we can prevent by releasing the struct_mutex and forcing our
i915/rcu workers to run, and in particular flushing the freed object
worker that is the cause for concern.

References: https://bugs.freedesktop.org/show_bug.cgi?id=107094Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180703101829.7360-1-chris@chris-wilson.co.uk

The PIPEDSL freezes on PSR entry and if PSR hasn't fully exited, then
the pipe_update_start call schedules itself out to check back later.

On ChromeOS-4.4 kernel, which is fairly up-to-date w.r.t drm/i915 but
lags w.r.t core kernel code, hot plugging an external display triggers
tons of "potential atomic update errors" in the dmesg, on *pipe A*. A
closer analysis reveals that we try to read the scanline 3 times and
eventually timeout, b/c PSR hasn't exited fully leading to a PIPEDSL
stuck @ 1599. This issue is not seen on upstream kernels, b/c for *some*
reason we loop inside intel_pipe_update start for ~2+ msec which in this
case is more than enough to exit PSR fully, hence an *unstuck* PIPEDSL
counter, hence no error. On the other hand, the ChromeOS kernel spends
~1.1 msec looping inside intel_pipe_update_start and hence errors out
b/c the source is still in PSR.

Regardless, we should wait for PSR exit (if PSR is disabled, we incur
a ~1-2 usec penalty) before reading the PIPEDSL, b/c if we haven't
fully exited PSR, then checking for vblank evasion isn't actually
applicable.

v4: Comment explaining psr_wait after enabling VBL interrupts (DK)

v5: CAN_PSR() to handle platforms that don't support PSR.

v6: Handle local_irq_disable on early return (Chris)
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: NTarun Vyas <tarun.vyas@intel.com>
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180627200250.1515-2-tarun.vyas@intel.com

This is a lockless version of the exisiting psr_wait_for_idle().
We want to wait for PSR to idle out inside intel_pipe_update_start.
At the time of a pipe update, we should never race with any psr
enable or disable code, which is a part of crtc enable/disable.
The follow up patch will use this lockless wait inside pipe_update_
start to wait for PSR to idle out before checking for vblank evasion.
We need to keep the wait in pipe_update_start to as less as it can be.
So,we can live and flourish w/o taking any psr locks at all.

Even if psr is never enabled, psr2_enabled will be false and this
function will wait for PSR1 to idle out, which should just return
immediately, so a very short (~1-2 usec) wait for cases where PSR
is disabled.

v2: Add comment to explain the 25msec timeout (DK)

v3: Rename psr_wait_for_idle to __psr_wait_for_idle_locked to avoid
    naming conflicts and propagate err (if any) to the caller (Chris)

v5: Form a series with the next patch

v7: Better explain the need for lockless wait and increase the max
    timeout to handle refresh rates < 60 Hz (Daniel Vetter)

v8: Rebase
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: NTarun Vyas <tarun.vyas@intel.com>
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180627200250.1515-1-tarun.vyas@intel.com

There is already a check to allow only RGB8888 formats with CCS
modifiers.
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628061854.6430-1-dhinakaran.pandiyan@intel.com

Prints live state of psr1.Extending the existing
PSR2 live state function to cover psr1.

Tested on KBL with psr2 and psr1 panel.

v2: rebase
v3: DK
    Rename psr2_live_status to psr_source_status.
v4: DK
    Move EDP_PSR_STATUS_STATE_SHIFT below EDP_PSR_STATUS_STATE_MASK.
    Pass seq to psr_source_status, handle source status prints in
    psr_source_status.
v5: Fixed CI warning messages
v6:
    Remove extra space in the title before the colon.(DK)
    Rebase. (Jani)
v7: Use tabs for indenting the values.(Jani)
v8: Addressed dk's review comments.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: NVathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530086910-15914-1-git-send-email-vathsala.nagaraju@intel.com

If the whole object is already pinned by HW for use as scanout, we will
fail to move it to the mappable region and so must resort to using a
partial VMA covering the whole object.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104513
Fixes: aa136d9d ("drm/i915: Convert partial ggtt vma to full ggtt if it spans the entire object")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: NMatthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180630090509.469-1-chris@chris-wilson.co.uk

Try to describe what the pick variants do, and which to prefer. No
functional changes.
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180629102039.2435-1-jani.nikula@intel.com

While debugging we may want to examine params passed to GuC.

v2: drop #ifdef DEBUG_GUC - Michal
Signed-off-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com> #1
Cc: Michal Winiarski <michal.winiarski@intel.com>
Reviewed-by: NMichał Winiarski <michal.winiarski@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618111821.47088-1-michal.wajdeczko@intel.com

make_obj_busy() makes a dummy busy object, but didn't attach the fence
to the reservation object, so it would not have registered as busy. For
completeness, attach the dummy request as the exclusive fence and mark
the object as written (in i915_vma_move_to_active)
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180629133717.11761-2-chris@chris-wilson.co.uk

We correctly attach the exclusive fetch for the scratch object when
emitting a request that writes into it, but for completeness we should
also declared the write to i915_vma_move_to_active()
Reported-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180629133717.11761-1-chris@chris-wilson.co.uk

The only time we should start FBC is when we have waited a vblank
after the atomic update. We've already forced a vblank wait by doing
wait_for_flip_done before intel_post_plane_update(), so we don't need
to wait a second time before enabling.

Removing the worker simplifies the code and removes possible race
conditions, like happening in 103167.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103167Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625163758.10871-2-maarten.lankhorst@linux.intel.comReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

There is a small race window in which FBC can be enabled after
pre_plane_update is called, but before the page flip has been
queued or completed.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103167
Link: https://patchwork.freedesktop.org/patch/msgid/20180625163758.10871-1-maarten.lankhorst@linux.intel.comReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

Back in commit 27af5eea ("drm/i915: Move execlists irq handler to a
bottom half"), we came to the conclusion that running our CSB processing
and ELSP submission from inside the irq handler was a bad idea. A really
bad idea as we could impose nearly 1s latency on other users of the
system, on average! Deferring our work to a tasklet allowed us to do the
processing with irqs enabled, reducing the impact to an average of about
50us.

We have since eradicated the use of forcewaked mmio from inside the CSB
processing and ELSP submission, bringing the impact down to around 5us
(on Kabylake); an order of magnitude better than our measurements 2
years ago on Broadwell and only about 2x worse on average than the
gem_syslatency on an unladen system.

In this iteration of the tasklet-vs-direct submission debate, we seek a
compromise where by we submit new requests immediately to the HW but
defer processing the CS interrupt onto a tasklet. We gain the advantage
of low-latency and ksoftirqd avoidance when waking up the HW, while
avoiding the system-wide starvation of our CS irq-storms.

Comparing the impact on the maximum latency observed (that is the time
stolen from an RT process) over a 120s interval, repeated several times
(using gem_syslatency, similar to RT's cyclictest) while the system is
fully laden with i915 nops, we see that direct submission an actually
improve the worse case.

Maximum latency in microseconds of a third party RT thread
(gem_syslatency -t 120 -f 2)
  x Always using tasklets (a couple of >1000us outliers removed)
  + Only using tasklets from CS irq, direct submission of requests
+------------------------------------------------------------------------+
|          +                                                             |
|          +                                                             |
|          +                                                             |
|          +       +                                                     |
|          + +     +                                                     |
|       +  + +     +  x     x     x                                      |
|      +++ + +     +  x  x  x  x  x  x                                   |
|      +++ + ++  + +  *x x  x  x  x  x                                   |
|      +++ + ++  + *  *x x  *  x  x  x                                   |
|    + +++ + ++  * * +*xxx  *  x  x  xx                                  |
|    * +++ + ++++* *x+**xx+ *  x  x xxxx x                               |
|   **x++++*++**+*x*x****x+ * +x xx xxxx x          x                    |
|x* ******+***************++*+***xxxxxx* xx*x     xxx +                x+|
|             |__________MA___________|                                  |
|      |______M__A________|                                              |
+------------------------------------------------------------------------+
    N           Min           Max        Median           Avg        Stddev
x 118            91           186           124     125.28814     16.279137
+ 120            92           187           109     112.00833     13.458617
Difference at 95.0% confidence
	-13.2798 +/- 3.79219
	-10.5994% +/- 3.02677%
	(Student's t, pooled s = 14.9237)

However the mean latency is adversely affected:

Mean latency in microseconds of a third party RT thread
(gem_syslatency -t 120 -f 1)
  x Always using tasklets
  + Only using tasklets from CS irq, direct submission of requests
+------------------------------------------------------------------------+
|           xxxxxx                                        +   ++         |
|           xxxxxx                                        +   ++         |
|           xxxxxx                                      + +++ ++         |
|           xxxxxxx                                     +++++ ++         |
|           xxxxxxx                                     +++++ ++         |
|           xxxxxxx                                     +++++ +++        |
|           xxxxxxx                                   + ++++++++++       |
|           xxxxxxxx                                 ++ ++++++++++       |
|           xxxxxxxx                                 ++ ++++++++++       |
|          xxxxxxxxxx                                +++++++++++++++     |
|         xxxxxxxxxxx    x                           +++++++++++++++     |
|x       xxxxxxxxxxxxx   x           +            + ++++++++++++++++++  +|
|           |__A__|                                                      |
|                                                      |____A___|        |
+------------------------------------------------------------------------+
    N           Min           Max        Median           Avg        Stddev
x 120         3.506         3.727         3.631     3.6321417    0.02773109
+ 120         3.834         4.149         4.039     4.0375167   0.041221676
Difference at 95.0% confidence
	0.405375 +/- 0.00888913
	11.1608% +/- 0.244735%
	(Student's t, pooled s = 0.03513)

However, since the mean latency corresponds to the amount of irqsoff
processing we have to do for a CS interrupt, we only need to speed that
up to benefit not just system latency but our own throughput.

v2: Remember to defer submissions when under reset.
v4: Only use direct submission for new requests
v5: Be aware that with mixing direct tasklet evaluation and deferred
tasklets, we may end up idling before running the deferred tasklet.
v6: Remove the redudant likely() from tasklet_is_enabled(), restrict the
annotation to reset_in_progress().
v7: Take the full timeline.lock when enabling perf_pmu stats as the
tasklet is no longer a valid guard. A consequence is that the stats are
now only valid for engines also using the timeline.lock to process
state.

Testcase: igt/gem_exec_latency/*rthog*
References: 27af5eea ("drm/i915: Move execlists irq handler to a bottom half")
Suggested-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628201211.13837-9-chris@chris-wilson.co.uk

Now that we use the CSB stored in the CPU friendly HWSP, we do not need
to track interrupts for when the mmio CSB registers are valid and can
just check where we read up to last from the cached HWSP. This means we
can forgo the atomic bit tracking from interrupt, and in the next patch
it means we can check the CSB at any time.

v2: Change the splitting inside reset_prepare, we only want to lose
testing the interrupt in this patch, the next patch requires the change
in locking
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628201211.13837-8-chris@chris-wilson.co.uk

As we now never read back our current head position from the CSB
pointers register, and the HW itself doesn't use it to prevent
overwriting unread CSB entries, we do not need to keep updating the
register. As it turns out this register is not listed as being shadowed,
and so requires forcewake -- but we haven't been taking forcewake around
it so the writes has probably been regularly dropped. Fortuitously, we
only read the value after a reset where it did not matter, and zero was
the right answer (well, close enough).

Mika pointed out that this was how we used to do it (accidentally!)
before he fixed it in commit cc53699b ("drm/i915: Use masked write
for Context Status Buffer Pointer").

References: cc53699b ("drm/i915: Use masked write for Context Status Buffer Pointer")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628201211.13837-7-chris@chris-wilson.co.uk

On HW reset, the HW clears the write pointer (to 0). But since it also
writes its first CSB entry to slot 0, we need to reset the write pointer
back to the element before (so the first entry we read is 0).

This is required for the next patch, where we trust the CSB completely!

v2: Use _MASKED_FIELD
v3: Store the reset value, so that we differentiate between mmio/hwsp
transparently and without pretense.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628201211.13837-6-chris@chris-wilson.co.uk

Following the removal of the last workarounds, the only CSB mmio access
is for the old vGPU interface. The mmio registers presented by vGPU do
not require forcewake and can be treated as ordinary volatile memory,
i.e. they behave just like the HWSP access just at a different location.
We can reduce the CSB access to a set of read/write/buffer pointers and
treat the various paths identically and not worry about forcewake.
(Forcewake is nightmare for worstcase latency, and we want to process
this all with irqsoff -- no latency allowed!)

v2: Comments, comments, comments. Well, 2 bonus comments.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628201211.13837-5-chris@chris-wilson.co.uk

In the next patch, we will process the CSB events directly from the
submission path, rather than only after a CS interrupt. Hence, we will
no longer have the need for a loop until the has-interrupt bit is clear,
and in the meantime can remove that small optimisation.

v2: Tvrtko pointed out it was safer to unconditionally kick the tasklet
after each irq, when assuming that the tasklet is called for each irq.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628201211.13837-4-chris@chris-wilson.co.uk

In the following patch, we will process the CSB events under the
timeline.lock and not serialised by the tasklet. This also means that we
will need to protect access to common variables such as
execlists->csb_head with the timeline.lock during reset.

v2: Move sync_irq to avoid deadlocks between taking timeline.lock from
our interrupt handler.
v3: Kill off the synchronize_hardirq as it raises more questions than
answered; now we use the timeline.lock entirely for CSB serialisation
between the irq and elsewhere, we don't need to be so heavy handed with
flushing
v4: Treat request cancellation (wedging after failed reset) similarly
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628201211.13837-3-chris@chris-wilson.co.uk

In the next patch, we will begin processing the CSB from inside the
submission path (underneath an irqsoff section, and even from inside
interrupt handlers). This means that updating the execlists->port[] will
no longer be serialised by the tasklet but needs to be locked by the
engine->timeline.lock instead. Pull dequeue and submit under the same
lock for protection. (An alternate future plan is to keep the in/out
arrays separate for concurrent processing and reduced lock coverage.)
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628201211.13837-2-chris@chris-wilson.co.uk

We do not need to do a posting read of our uncached mmio write to
re-enable the master interrupt lines after handling an interrupt, so
don't. This saves us a slow UC read before we can process the interrupt,
most noticeable in execlists where any stalls imposes extra latency on
GPU command execution.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NVille Syrjala <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628201211.13837-1-chris@chris-wilson.co.uk

We're fetching GuC/HuC firmwares directly from uc level during
init_early stage but this breaks guc/huc struct isolation and
also strict SW-only initialization rule for init_early. Move fw
fetching to init phase and do it separately per guc/huc struct.

v2: don't forget to move wopcm_init - Michele
v3: fetch in init_misc phase - Michal
Signed-off-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com> #2
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628141522.62788-2-michal.wajdeczko@intel.com

We will add more init steps to misc phase and there is no need
to expose them separately for use in uc_init_misc function.
Signed-off-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628141522.62788-1-michal.wajdeczko@intel.com

Avoid calling dma_fence_signal() from inside the interrupt if we haven't
enabled signaling on the request.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180627201304.15817-4-chris@chris-wilson.co.uk

Rather than have multiple locked instructions inside the notify_ring()
irq handler, move them inside the spinlock and reduce their intrinsic
locking.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180627201304.15817-3-chris@chris-wilson.co.uk

If we have more interrupts pending (because we know there are more
breadcrumb signals before the completion), then we do not need to
trigger an irq_seqno_barrier or even wakeup the task on this interrupt
as there will be another. To allow some margin of error (we are trying
to work around incoherent seqno after all), we wakeup the breadcrumb
before the target as well as on the target.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180627201304.15817-2-chris@chris-wilson.co.uk

By taking advantage of the RCU protection of the task struct, we can find
the appropriate signaler under the spinlock and then release the spinlock
before waking the task and signaling the fence.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180627201304.15817-1-chris@chris-wilson.co.uk

At the moment, gem_exec_gttfill fails with a sporadic EBUSY due to us
wanting to unbind a pinned batch. Let's dump who first bound that vma to
see if that helps us identify who still unexpectedly has it pinned.

v2: We cannot allocate inside the printer (as it may be on an fs-reclaim
path), so hope for the best and build the string on the stack
v3: stack depth of 16 routinely overflows a 512 character string, limit
it to 12 to avoid unsightly truncation.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628132206.8329-1-chris@chris-wilson.co.uk

This patch unifies the naming of DRM functions for reference counting
of struct drm_device. The resulting code is more aligned with the rest
of the Linux kernel interfaces.
Signed-off-by: NThomas Zimmermann <tdz@users.sourceforge.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618110154.30462-6-tdz@users.sourceforge.net

This patch unifies the naming of DRM functions for reference counting
of struct drm_gem_object. The resulting code is more aligned with the
rest of the Linux kernel interfaces.
Signed-off-by: NThomas Zimmermann <tdz@users.sourceforge.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618110154.30462-5-tdz@users.sourceforge.net

This patch unifies the naming of DRM functions for reference counting
of struct drm_gem_object. The resulting code is more aligned with the
rest of the Linux kernel interfaces.
Signed-off-by: NThomas Zimmermann <tdz@users.sourceforge.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618110154.30462-4-tdz@users.sourceforge.net

This patch unifies the naming of DRM functions for reference counting
of struct drm_gem_object. The resulting code is more aligned with the
rest of the Linux kernel interfaces.
Signed-off-by: NThomas Zimmermann <tdz@users.sourceforge.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618110154.30462-3-tdz@users.sourceforge.net

This patch unifies the naming of DRM functions for reference counting
of struct drm_connector. The resulting code is more aligned with the
rest of the Linux kernel interfaces.
Signed-off-by: NThomas Zimmermann <tdz@users.sourceforge.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618110154.30462-2-tdz@users.sourceforge.net

This patch addresses Interrupts from south display engine (SDE).

ICP has two registers - SHOTPLUG_CTL_DDI and SHOTPLUG_CTL_TC.
Introduce these registers and their intended values.

Introduce icp_irq_handler().

The icp_irq_postinstall() takes care of
enabling all PCH interrupt sources, to unmask
them as needed with SDEIMR, as is done
done by ibx_irq_pre_postinstall() for earlier platforms.
We do not need to explicitly call the ibx_irq_pre_postinstall().

Also, while changing these,
s/CPT/PPT/CPT-CNP comment.

v2:
- remove redundant register defines.(Lucas)
- Change register names to be more consistent with
previous platforms (Lucas)

v3:
-Reorder bit defines to a more appropriate location.
 Change the comments. Confirm in the commit message that
 icp_irq_postinstall() need not go to
 ibx_irq_pre_postinstall() and ibx_irq_postinstall()
 as in earlier platforms. (Paulo)

Cc: Lucas De Marchi <lucas.de.marchi@gmail.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
[Paulo: coding style bikesheds and rebases].
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530046343-30649-1-git-send-email-anusha.srivatsa@intel.com

In the next^W forthcoming patch, we will start to defer retiring the
request from the engine list if it is still active on the submission
backend. To preserve the semantics that after wait-for-idle completes
the system is idle and fully retired, we need to therefore wait for the
backends to idle before calling i915_retire_requests().
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180627115334.16282-1-chris@chris-wilson.co.uk

Add the definition for ICL power wells and their mapping to power
domains. On ICL there are 3 power well control registers, we'll select
the correct one based on higher bits of the power well ID. The offset
for the control and status flags within this register is based on the
lower bits of the ID as on older platforms.

As the DC state programming is also the same as on old platforms we can
reuse the corresponding helpers. For this we mark here the DC-off power
well as shared among multiple platforms.

Other than the above the delta between old platforms and ICL:
- Pipe C has its own power well, so we can save some additional power in the
  pipe A+B and (non-eDP) pipe A configurations.
- Power wells for port E/F DDI/AUX IO and Thunderbolt 1-4 AUX IO

v2:
- Rebase on drm-tip after prep patch for this was merged there as
  requested by Paulo.
- Actually add the new AUX and DDI power well control regs (Rakshmi)

v3:
- Fix power well register names in code comments
- Add TBT AUX->power well 3 dependency

v4:
- Rebase

v5:
- Detach AUX power wells from the INIT power domain. These power wells
  can only be enabled in a TC/TBT connected state and otherwise not
  needed during driver initialization.

v6:
- Use _MMIO_PORT(...) instead _MMIO(_PICK(...)) (Paulo)
  Fix checkpatch warnings.

Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Rakshmi Bhatia <rakshmi.bhatia@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com> (v1)
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626142232.22361-1-imre.deak@intel.com