Allocating 2 buffers per page is insanely inefficient when MTU is 1500
and PAGE_SIZE is 64K (as it usually is on POWER).  Allocate as many as
we can fit, and choose the refill batch size at run-time so that we
still always use a whole page at once.

[bwh: Fix loop condition to allow for compound pages; rebase]
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

This condition is brittle and we have lots of flags to spare.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

On POWER systems, DMA mapping/unmapping operations are very expensive.
These changes reduce these costs by trying to reuse DMA mapped pages.

After all the buffers associated with a page have been processed and
passed up, the page is placed into a ring (if there is room).  For
each page that is required for a refill operation, a page in the ring
is examined to determine if its page count has fallen to 1, ie. the
kernel has released its reference to these packets.  If this is the
case, the page can be immediately added back into the RX descriptor
ring, without having to re-map it for DMA.

If the kernel is still holding a reference to this page, it is removed
from the ring and unmapped for DMA.  Then a new page, which can
immediately be used by RX buffers in the descriptor ring, is allocated
and DMA mapped.

The time a page needs to spend in the recycle ring before the kernel
has released its page references is based on the number of buffers
that use this page.  As large pages can hold more RX buffers, the RX
recycle ring can be shorter.  This reduces memory usage on POWER
systems, while maintaining the performance gain achieved by recycling
pages, following the driver change to pack more than two RX buffers
into large pages.

When an IOMMU is not present, the recycle ring can be small to reduce
memory usage, since DMA mapping operations are inexpensive.

With a small recycle ring, attempting to refill the descriptor queue
with more buffers than the equivalent size of the recycle ring could
ultimately lead to memory leaks if page entries in the recycle ring
were overwritten.  To prevent this, the check to see if the recycle
ring is full is changed to check if the next entry to be written is
NULL.

[bwh: Combine and rebase several commits so this is complete
 before the following buffer-packing changes.  Remove module
 parameter.]
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Enable RX DMA scattering iff an RX buffer large enough for the current
MTU will not fit into a single page and the NIC supports DMA
scattering for kernel-mode RX queues.

On Falcon and Siena, the RX_USR_BUF_SIZE field is used as the DMA
limit for both all RX queues with scatter enabled.  Set it to 1824,
matching what Onload uses now.

Maintain a statistic for frames truncated due to lack of descriptors
(rx_nodesc_trunc).  This is distinct from rx_frm_trunc which may be
incremented when scattering is disabled and implies an over-length
frame.

Whenever an MTU change causes scattering to be turned on or off,
update filters that point to the PF queues, but leave others
unchanged, as VF drivers assume scattering is off.

Add n_frags parameters to various functions, and make them iterate:
- efx_rx_packet()
- efx_recycle_rx_buffers()
- efx_rx_mk_skb()
- efx_rx_deliver()

Make efx_handle_rx_event() responsible for updating
efx_rx_queue::removed_count.

Change the RX pipeline state to a starting ring index and number of
fragments, and make __efx_rx_packet() responsible for clearing it.

Based on earlier versions by David Riddoch and Jon Cooper.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Adjust rx_buf->page_offset when we eat the RX hash prefix.  Remove
efx_rx_buf_offset(), which is now redundant.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Currently we prefetch from the Ethernet header, but we will also read
the hash prefix.  In practice they should be in the same cache line
and this won't hurt, but it is still pointless to add on the hash
prefix size.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

efx_rx_buf_va() returns the virtual address of the current start of
the buffer.  The callers must add the hash prefix size themselves.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

The pipeline mechanism will need to change a bit for scattered
packets.  Add a wrapper to insulate efx_process_channel() from this.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Replace efx_nic::rx_buffer_len with efx_nic::rx_dma_len, the maximum
RX DMA length.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

The Linux side of EEH is triggered by MMIO reads, but this
driver's data path does not issue any MMIO reads (except in
legacy interrupt mode).  Therefore add a monitor function
to poll EEH periodically.

When preparing to reset the device based on our own error
detection, also poll EEH and defer to its recovery mechanism
if appropriate.

[bwh: Use a separate condition for the initial link poll; fix some
 style errors]
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

On Siena, VFs share RSS configuration with the PF.  We attempted to
support configurations where the PF only uses 1 RX queue and VFs use
multiple RX queues, by (1) setting up RSS for the number of RX queues
per VF (2) disabling RSS in the PF's RX default filters.

Unfortunately commit cd2d5b52 ('sfc: Add SR-IOV back-end support
for SFC9000 family') only included (1).  This is (2).
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

efx_filter_insert_filter() uses the first table entry in the hash chain
that either has the same match values or is empty.  This means that
replacement doesn't always work correctly:

1. Insert filter F1 with match values M1, hashing to H1, at first
   possible entry E1.
2. Insert filter F2 with match values M2, hashing to H1, at second
   possible entry E2.
3. Remove filter F1.
4. Insert filter F3 with match values M2, hashing to H1, at first
   possible entry E1.

F3 should have either replaced F2 or been rejected (depending on
priority and the replace_equal parameter).

Instead, search for both a matching filter that the inserted filter
would replace, and an available insertion point, up to the applicable
maximum search depths.  If we insert at lower depth than a replaced
filter, clear the replaced filter.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

efx_filter_search() is only called from efx_filter_insert(), and
neither function is very long.  The following bug fix requires a more
sophisticated search with a third result, which is going to be easier
to implement as part of the same function.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

These functions happen to work for default MAC filters: they generate
an initial index of 1/0 for unicast/multicast respectively and an
increment of 1 for either, so a search succeeds at depth 2.  But this
is a matter of luck rather than design, and it really won't work well
with the bug fix we're about to do.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

The 'for_insert' parameter is redundant since there are no longer
any other operations that need to search based on a filter spec.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

The 'replace' flag to efx_filter_insert_filter() controls whether the
new filter may replace *any* filter, and is checked even before
priority comparison.  But lower-priority filters should never
block insertion of higher-priority filters.

Change the priority checking so that lower-priority filters are
replaced regardless of the value of the flag, and rename the
flag to 'replace_equal'.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

[bwh: Remove more dead code, and make efx_ptp_rx() pull the data it
 needs into the header area.]
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

There is a long-standing problem with the packet-timestamp matching in
the driver. When a PTP packet is received by the MC, the FPGA
timestamps the packet and the MC sends the timestamp and 6 bytes of
the UUID to the driver. The driver then matches the timestamp against
received packets using the same 6 bytes of UUID.

The problem comes from the choice of which 6 bytes to use. The PTP
spec is slightly contradictory and misleading in one of the two places
where the UUIDs are discussed. From section 7.2.2.2 of the spec, a
PTPD2 UUID can be either a EUI-64 or a EUI-64 constructed from a
EUI-48. The typical ethernet based implementation uses a EUI-64
constructed from a EUI-48. This works by taking the first 3 bytes of
the MAC address of the NIC being used for PTP (the OUI), then
inserting 0xFF, 0xFE, then taking the last 3 bytes of the MAC address
giving
          MAC[0], MAC[1], MAC[2], 0xFF, 0xFE, MAC[3], MAC[4], MAC[5]
The current MC firmware and driver discard the first two bytes of this
UUID and packets are matched against timestamps using bytes 2 to 7 so
there is a small risk that in a deployment of Solarflare PTP NICs used
with other vendors NICs, that a PTP packet could be matched against
the wrong timestamp. This applies to all other organisations whose
third byte of the OUI is 0x53. It's a long list but I notice that it
includes Cisco.

The necessary modifications to use bytes 0-2 and 5-7 of the UUID to
match against are quite small but introduce incompatibility between
older version of the firmware and driver.

When PTP is enabled via SO_TIMESTAMPING specifying PTP V2, the driver
will try to enable PTP in the firmware using the enhanced mode
(above). If the firmware returns an error, the driver will enable PTP
in the firmware using the old mode.

[bwh: Fix some style errors; remove private ioctl bits]
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Instead of having efx_ptp_rx() call netif_receive_skb() for an invalid
PTP packet, make it return false for rejected packets and have
efx_rx_deliver() pass them up.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

We are currently busy waiting for MDIO registers to complete their
operation but we did not propagate the result back to the caller.
Update r6040_phy_{read,write} to report the busy waiting result
accordingly.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RX DMA buffers start at an offset of EFX_PAGE_IP_ALIGN bytes from the
start of a cache line.  This offset obviously needs to be included in
the virtual address, but this was missed in commit b590ace0
('sfc: Fix efx_rx_buf_offset() in the presence of swiotlb') since
EFX_PAGE_IP_ALIGN is equal to 0 on both x86 and powerpc.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

efx_device_detach_sync() locks all TX queues before marking the device
detached and thus disabling further TX scheduling.  But it can still
be interrupted by TX completions which then result in TX scheduling in
soft interrupt context.  This will deadlock when it tries to acquire
a TX queue lock that efx_device_detach_sync() already acquired.

To avoid deadlock, we must use netif_tx_{,un}lock_bh().
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

BQL (Byte Queue Limits) proper operation needs TX completion
being serviced in a timely fashion.

bnx2x uses a non standard NAPI poll weight, and thats not fair to other
napi poll handlers, and even not reasonable.

Use the default value instead.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch uses module_platform_driver_probe() macro which makes
the code smaller and simpler.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch uses module_platform_driver_probe() macro which makes
the code smaller and simpler.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch uses module_platform_driver_probe() macro which makes
the code smaller and simpler.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

build error cause by
Commit ff43da86
("NET: FEC: dynamtic check DMA desc buff type")

drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_get_nextdesc’:
drivers/net/ethernet/freescale/fec.c:215:18: error: invalid use of undefined type ‘struct bufdesc_ex’
drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_get_prevdesc’:
drivers/net/ethernet/freescale/fec.c:224:18: error: invalid use of undefined type ‘struct bufdesc_ex’
drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_start_xmit’:
drivers/net/ethernet/freescale/fec.c:286:37: error: arithmetic on pointer to an incomplete type
drivers/net/ethernet/freescale/fec.c:287:13: error: arithmetic on pointer to an incomplete type
drivers/net/ethernet/freescale/fec.c:324:7: error: dereferencing pointer to incomplete type etc....
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

up stack ndo_start_xmit already hold lock.
fec_enet_start_xmit needn't spin lock.
stat_xmit just update fep->cur_tx
fec_enet_tx just update fep->dirty_tx

Reserve a empty bdb to check full or empty
cur_tx == dirty_tx    means full
cur_tx == dirty_tx +1 means empty

So needn't is_full variable.

Fix spin lock deadlock

=================================
[ INFO: inconsistent lock state ]
3.8.0-rc5+ #107 Not tainted
---------------------------------
inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage.
ptp4l/615 [HC1[1]:SC0[0]:HE0:SE1] takes:
 (&(&list->lock)->rlock#3){?.-...}, at: [<8042c3c4>] skb_queue_tail+0x20/0x50
 {HARDIRQ-ON-W} state was registered at:
 [<80067250>] mark_lock+0x154/0x4e8
 [<800676f4>] mark_irqflags+0x110/0x1a4
 [<80069208>] __lock_acquire+0x494/0x9c0
 [<80069ce8>] lock_acquire+0x90/0xa4
 [<80527ad0>] _raw_spin_lock_bh+0x44/0x54
 [<804877e0>] first_packet_length+0x38/0x1f0
 [<804879e4>] udp_poll+0x4c/0x5c
 [<804231f8>] sock_poll+0x24/0x28
 [<800d27f0>] do_poll.isra.10+0x120/0x254
 [<800d36e4>] do_sys_poll+0x15c/0x1e8
 [<800d3828>] sys_poll+0x60/0xc8
 [<8000e780>] ret_fast_syscall+0x0/0x3c

 *** DEADLOCK ***

 1 lock held by ptp4l/615:
  #0:  (&(&fep->hw_lock)->rlock){-.-...}, at: [<80355f9c>] fec_enet_tx+0x24/0x268
  stack backtrace:
  Backtrace:
  [<800121e0>] (dump_backtrace+0x0/0x10c) from [<80516210>] (dump_stack+0x18/0x1c)
  r6:8063b1fc r5:bf38b2f8 r4:bf38b000 r3:bf38b000
  [<805161f8>] (dump_stack+0x0/0x1c) from [<805189d0>] (print_usage_bug.part.34+0x164/0x1a4)
  [<8051886c>] (print_usage_bug.part.34+0x0/0x1a4) from [<80518a88>] (print_usage_bug+0x78/0x88)
  r8:80065664 r7:bf38b2f8 r6:00000002 r5:00000000 r4:bf38b000
  [<80518a10>] (print_usage_bug+0x0/0x88) from [<80518b58>] (mark_lock_irq+0xc0/0x270)
  r7:bf38b000 r6:00000002 r5:bf38b2f8 r4:00000000
  [<80518a98>] (mark_lock_irq+0x0/0x270) from [<80067270>] (mark_lock+0x174/0x4e8)
  [<800670fc>] (mark_lock+0x0/0x4e8) from [<80067744>] (mark_irqflags+0x160/0x1a4)
  [<800675e4>] (mark_irqflags+0x0/0x1a4) from [<80069208>] (__lock_acquire+0x494/0x9c0)
  r5:00000002 r4:bf38b2f8
  [<80068d74>] (__lock_acquire+0x0/0x9c0) from [<80069ce8>] (lock_acquire+0x90/0xa4)
  [<80069c58>] (lock_acquire+0x0/0xa4) from [<805278d8>] (_raw_spin_lock_irqsave+0x4c/0x60)
  [<8052788c>] (_raw_spin_lock_irqsave+0x0/0x60) from [<8042c3c4>] (skb_queue_tail+0x20/0x50)
  r6:bfbb2180 r5:bf1d0190 r4:bf1d0184
  [<8042c3a4>] (skb_queue_tail+0x0/0x50) from [<8042c4cc>] (sock_queue_err_skb+0xd8/0x188)
  r6:00000056 r5:bfbb2180 r4:bf1d0000 r3:00000000
  [<8042c3f4>] (sock_queue_err_skb+0x0/0x188) from [<8042d15c>] (skb_tstamp_tx+0x70/0xa0)
  r6:bf0dddb0 r5:bf1d0000 r4:bfbb2180 r3:00000004
  [<8042d0ec>] (skb_tstamp_tx+0x0/0xa0) from [<803561d0>] (fec_enet_tx+0x258/0x268)
  r6:c089d260 r5:00001c00 r4:bfbd0000
  [<80355f78>] (fec_enet_tx+0x0/0x268) from [<803562cc>] (fec_enet_interrupt+0xec/0xf8)
  [<803561e0>] (fec_enet_interrupt+0x0/0xf8) from [<8007d5b0>] (handle_irq_event_percpu+0x54/0x1a0)
  [<8007d55c>] (handle_irq_event_percpu+0x0/0x1a0) from [<8007d740>] (handle_irq_event+0x44/0x64)
  [<8007d6fc>] (handle_irq_event+0x0/0x64) from [<80080690>] (handle_fasteoi_irq+0xc4/0x15c)
  r6:bf0dc000 r5:bf811290 r4:bf811240 r3:00000000
  [<800805cc>] (handle_fasteoi_irq+0x0/0x15c) from [<8007ceec>] (generic_handle_irq+0x28/0x38)
  r5:807130c8 r4:00000096
  [<8007cec4>] (generic_handle_irq+0x0/0x38) from [<8000f16c>] (handle_IRQ+0x54/0xb4)
  r4:8071d280 r3:00000180
  [<8000f118>] (handle_IRQ+0x0/0xb4) from [<80008544>] (gic_handle_irq+0x30/0x64)
  r8:8000e924 r7:f4000100 r6:bf0ddef8 r5:8071c974 r4:f400010c
  r3:00000000
  [<80008514>] (gic_handle_irq+0x0/0x64) from [<8000e2e4>] (__irq_svc+0x44/0x5c)
  Exception stack(0xbf0ddef8 to 0xbf0ddf40)
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not include the frame check sequence when adding the skb to
netif_receive_skb(). This causes problems when this interface was
bridged to a wifi ap and a big package should be forwarded from this
Ethernet driver through a bride to the wifi client.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix condition typo for running KR2 work-around though it doesn't have
real effect since the typo bits matched by chance.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix KR2 link down problem after reboot when link speed is reconfigured via ethtool.
Since 1G/10G support link speed were missing by default, 1G/10G link speed were
not advertised.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the "ethtool -p" for boards with BCM84834, by using LED4 of the PHY
to toggle the link LED while keeping interrupt disabled to avoid NIG attentions,
and at the end restore NIG to previous state.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some hardware start settings implicitely assume an usual 1500 bytes mtu
that can't be guaranteed because changes of mtu may be requested both
before and after the hardware is started.
Reported-by: NTomi Orava <tomimo@ncircle.nullnet.fi>
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I'm not sure why, but the hlist for each entry iterators were conceived

        list_for_each_entry(pos, head, member)

The hlist ones were greedy and wanted an extra parameter:

        hlist_for_each_entry(tpos, pos, head, member)

Why did they need an extra pos parameter? I'm not quite sure. Not only
they don't really need it, it also prevents the iterator from looking
exactly like the list iterator, which is unfortunate.

Besides the semantic patch, there was some manual work required:

 - Fix up the actual hlist iterators in linux/list.h
 - Fix up the declaration of other iterators based on the hlist ones.
 - A very small amount of places were using the 'node' parameter, this
 was modified to use 'obj->member' instead.
 - Coccinelle didn't handle the hlist_for_each_entry_safe iterator
 properly, so those had to be fixed up manually.

The semantic patch which is mostly the work of Peter Senna Tschudin is here:

@@
iterator name hlist_for_each_entry, hlist_for_each_entry_continue, hlist_for_each_entry_from, hlist_for_each_entry_rcu, hlist_for_each_entry_rcu_bh, hlist_for_each_entry_continue_rcu_bh, for_each_busy_worker, ax25_uid_for_each, ax25_for_each, inet_bind_bucket_for_each, sctp_for_each_hentry, sk_for_each, sk_for_each_rcu, sk_for_each_from, sk_for_each_safe, sk_for_each_bound, hlist_for_each_entry_safe, hlist_for_each_entry_continue_rcu, nr_neigh_for_each, nr_neigh_for_each_safe, nr_node_for_each, nr_node_for_each_safe, for_each_gfn_indirect_valid_sp, for_each_gfn_sp, for_each_host;

type T;
expression a,c,d,e;
identifier b;
statement S;
@@

-T b;
    <+... when != b
(
hlist_for_each_entry(a,
- b,
c, d) S
|
hlist_for_each_entry_continue(a,
- b,
c) S
|
hlist_for_each_entry_from(a,
- b,
c) S
|
hlist_for_each_entry_rcu(a,
- b,
c, d) S
|
hlist_for_each_entry_rcu_bh(a,
- b,
c, d) S
|
hlist_for_each_entry_continue_rcu_bh(a,
- b,
c) S
|
for_each_busy_worker(a, c,
- b,
d) S
|
ax25_uid_for_each(a,
- b,
c) S
|
ax25_for_each(a,
- b,
c) S
|
inet_bind_bucket_for_each(a,
- b,
c) S
|
sctp_for_each_hentry(a,
- b,
c) S
|
sk_for_each(a,
- b,
c) S
|
sk_for_each_rcu(a,
- b,
c) S
|
sk_for_each_from
-(a, b)
+(a)
S
+ sk_for_each_from(a) S
|
sk_for_each_safe(a,
- b,
c, d) S
|
sk_for_each_bound(a,
- b,
c) S
|
hlist_for_each_entry_safe(a,
- b,
c, d, e) S
|
hlist_for_each_entry_continue_rcu(a,
- b,
c) S
|
nr_neigh_for_each(a,
- b,
c) S
|
nr_neigh_for_each_safe(a,
- b,
c, d) S
|
nr_node_for_each(a,
- b,
c) S
|
nr_node_for_each_safe(a,
- b,
c, d) S
|
- for_each_gfn_sp(a, c, d, b) S
+ for_each_gfn_sp(a, c, d) S
|
- for_each_gfn_indirect_valid_sp(a, c, d, b) S
+ for_each_gfn_indirect_valid_sp(a, c, d) S
|
for_each_host(a,
- b,
c) S
|
for_each_host_safe(a,
- b,
c, d) S
|
for_each_mesh_entry(a,
- b,
c, d) S
)
    ...+>

[akpm@linux-foundation.org: drop bogus change from net/ipv4/raw.c]
[akpm@linux-foundation.org: drop bogus hunk from net/ipv6/raw.c]
[akpm@linux-foundation.org: checkpatch fixes]
[akpm@linux-foundation.org: fix warnings]
[akpm@linux-foudnation.org: redo intrusive kvm changes]
Tested-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: NSasha Levin <sasha.levin@oracle.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since commit 86564c3f "bnx2x: Remove many sparse warnings" UDP
csum offload is broken for 57710/57711. Fix return value.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
CC: Ariel Elior <ariele@broadcom.com>
CC: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make cpsw_add_default_vlan() look at the actual number of slaves for its
iteration, so boards with less than 2 slaves don't ooops at boot.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We must only ever stop TX queues when they are full or the net device
is not 'ready' so far as the net core, and specifically the watchdog,
is concerned.  Otherwise, the watchdog may fire *immediately* if no
packets have been added to the queue in the last 5 seconds.

The device is ready if all the following are true:

(a) It has a qdisc
(b) It is marked present
(c) It is running
(d) The link is reported up

(a) and (c) are normally true, and must not be changed by a driver.
(d) is under our control, but fake link changes may disturb userland.
This leaves (b).  We already mark the device absent during reset
and self-test, but we need to do the same during MTU changes and ring
reallocation.  We don't need to do this when the device is brought
down because then (c) is already false.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>