Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
接近 2 年 前同步成功

通知 170
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 20 8月, 2009 8 次提交
  3. 14 8月, 2009 13 次提交
  5. 05 8月, 2009 5 次提交
    • G
      b43: implement baseband init for LP-PHY <= rev1 · 738f0f43
      由 Gábor Stefanik 提交于 
      Implement baseband init for rev.0 and rev.1 LP PHYs. Convert boardflags_hi values to defines.
Implement b43_phy_copy for easier copying between registers, as needed by LP-PHY init.

Signed-off-by: Gábor Stefanik<netrolller.3d@gmail.com>
Cc: Michael Buesch<mb@bu3sch.de>
Cc: Larry Finger<larry.finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      738f0f43
    • G
      b43: remove wrong probe_resp_plcp write · 92ca8d43
      由 gregor kowski 提交于 
      The tkip hw support uncovered a bug in b43_write_probe_resp_template : it is
writing at the wrong shm offset, it is in the B43_SHM_SH_TKIPTSCTTAK zone. This
patch comments these writes.
Signed-off-by: NGregor Kowski <gregor.kowski@gmail.com>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      92ca8d43
    • M
      b43: Fix unaligned 32bit SHM-shared access · f62ae6cd
      由 Michael Buesch 提交于 
      This fixes unaligned 32bit SHM-shared read/write access.
The low and high 16 bits were swapped.
It also adds a testcase for this to the chipaccess validation.

(Thanks to Albert Herranz for tracking down this bug.)
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      f62ae6cd
    • L
      mac80211: redefine usage of the mac80211 workqueue · 42935eca
      由 Luis R. Rodriguez 提交于 
      The mac80211 workqueue exists to enable mac80211 and drivers
to queue their own work on a single threaded workqueue. mac80211
takes care to flush the workqueue during suspend but we never
really had requirements on drivers for how they should use
the workqueue in consideration for suspend.

We extend mac80211 to document how the mac80211 workqueue should
be used, how it should not be used and finally move raw access to
the workqueue to mac80211 only. Drivers and mac80211 use helpers
to queue work onto the mac80211 workqueue:

  * ieee80211_queue_work()
  * ieee80211_queue_delayed_work()

These helpers will now warn if mac80211 already completed its
suspend cycle and someone is trying to queue work. mac80211
flushes the mac80211 workqueue prior to suspend a few times,
but we haven't taken the care to ensure drivers won't add more
work after suspend. To help with this we add a warning when
someone tries to add work and mac80211 already completed the
suspend cycle.

Drivers should ensure they cancel any work or delayed work
in the mac80211 stop() callback.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      42935eca
    • L
      b43: Work around mac80211 race condition · 18c69510
      由 Larry Finger 提交于 
      As shown in http://thread.gmane.org/gmane.linux.kernel.wireless.general/36497,
mac80211 has a bug that allows a call to the TX routine after the queues have
been stopped. This situation will only occur under extreme stress. Although
b43 does not crash when this condition occurs, it does generate a WARN_ON and
also logs a queue overrun message. This patch recognizes b43 is not at fault
and logs a message only when the most verbose debugging mode is enabled. In
the unlikely event that the queue is not stopped when the DMA queue becomes
full, then a warning is issued.

During testing of this patch with one output stream running repeated tcpperf
writes and a second running a flood ping, this routine was entered with
the DMA ring stopped about once per hour. The condition where the DMA queue is
full but the ring has not been stopped has never been seen by me.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      18c69510
  7. 25 7月, 2009 1 次提交
  9. 11 7月, 2009 1 次提交
    • J
      mac80211: push rx status into skb->cb · f1d58c25
      由 Johannes Berg 提交于 
      Within mac80211, we often need to copy the rx status into
skb->cb. This is wasteful, as drivers could be building it
in there to start with. This patch changes the API so that
drivers are expected to pass the RX status in skb->cb, now
accessible as IEEE80211_SKB_RXCB(skb). It also updates all
drivers to pass the rx status in there, but only by making
them memcpy() it into place before the call to the receive
function (ieee80211_rx(_irqsafe)). Each driver can now be
optimised on its own schedule.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      f1d58c25
  11. 09 7月, 2009 1 次提交
  13. 08 7月, 2009 1 次提交
  15. 11 6月, 2009 3 次提交
  17. 04 6月, 2009 1 次提交
    • J
      rfkill: rewrite · 19d337df
      由 Johannes Berg 提交于 
      This patch completely rewrites the rfkill core to address
the following deficiencies:

 * all rfkill drivers need to implement polling where necessary
   rather than having one central implementation

 * updating the rfkill state cannot be done from arbitrary
   contexts, forcing drivers to use schedule_work and requiring
   lots of code

 * rfkill drivers need to keep track of soft/hard blocked
   internally -- the core should do this

 * the rfkill API has many unexpected quirks, for example being
   asymmetric wrt. alloc/free and register/unregister

 * rfkill can call back into a driver from within a function the
   driver called -- this is prone to deadlocks and generally
   should be avoided

 * rfkill-input pointlessly is a separate module

 * drivers need to #ifdef rfkill functions (unless they want to
   depend on or select RFKILL) -- rfkill should provide inlines
   that do nothing if it isn't compiled in

 * the rfkill structure is not opaque -- drivers need to initialise
   it correctly (lots of sanity checking code required) -- instead
   force drivers to pass the right variables to rfkill_alloc()

 * the documentation is hard to read because it always assumes the
   reader is completely clueless and contains way TOO MANY CAPS

 * the rfkill code needlessly uses a lot of locks and atomic
   operations in locked sections

 * fix LED trigger to actually change the LED when the radio state
   changes -- this wasn't done before
Tested-by: NAlan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> [thinkpad]
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      19d337df
  19. 23 5月, 2009 1 次提交
  21. 21 5月, 2009 1 次提交
  23. 07 5月, 2009 2 次提交
  25. 23 4月, 2009 2 次提交