Support for it is incomplete
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Re-train if the calibrated PA linearization curve is out of bounds
(affects AR933x and AR9485).
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

That predistortion type is not supported
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The interrupt is no longer handling it. While it shouldn't fire (wraparound
is highly unlikely), the consequences would be fatal (interrupt storm).
Disable the interrupt to prevent that from happening.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

According to the vendor driver v2.6.0.1, during the rf register init the SRAM
voltage should be increased to 1.35V and after 1ms decreased back to 1.2V. This
patch adds the field setting of LDO_CFG0_LDO_CORE_VLEVEL accordingly.

Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NMarc Kleine-Budde <mkl@blackshift.org>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we send a command to firmware, we assumed that cmd_size
will be always less than or equal to the structure size of
host_cmd_ds_command. However, this is no longer true after
we added AP support. There are some AP commands that Custom
IE TLVs are included in command buffer, hence the cmd_size
gets enlarged by the TLV data. We need to increase the skb
length for the extra data.
Signed-off-by: NStone Piao <piaoyun@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This change marks interface as down on reset, otherwise the driver can't
reinitialize itself properly.

Without the change a transient problem turns out to be critical and leads
to inavailability to reset the driver without brcmsmac module unload/load
cycle:

    ieee80211 phy0: wl0: PSM microcode watchdog fired at 5993 (seconds). Resetting.
    brcms_c_dpc : PSM Watchdog, chipid 0xa8d9, chiprev 0x1
    ieee80211 phy0: wl0: fatal error, reinitializing
    ieee80211 phy0: Hardware restart was requested
    ieee80211 phy0: brcms_ops_start: brcms_up() returned -19
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If the device is not started, we can't read its
SRAM and attempting to do so will cause issues.
Protect the debugfs read.

Cc: stable@vger.kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl_dbgfs_fh_reg_read() can cause crashes and/or
BUG_ON in slub because the ifdefs are wrong, the
code in iwl_dump_fh() should use DEBUGFS, not
DEBUG to protect the buffer writing code.

Also, while at it, clean up the arguments to the
function, some code and make it generally safer.

Cc: stable@vger.kernel.org
Reported-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The result of one call to a function is tested, and then at the second call
to the same function, the previous result, and not the current result, is
tested again.

Also changed &bssid to bssid, at the suggestion of Stanislav Yakovlev.

The semantic match that finds the first problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression ret;
identifier f;
statement S1,S2;
@@

*ret = f(...);
if (\(ret != 0\|ret < 0\|ret == NULL\)) S1
... when any
*f(...);
if (\(ret != 0\|ret < 0\|ret == NULL\)) S2
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch reduces the per rate target power eeprom reads for
AR5K_EEPROM_MODE_11A from 10 to 8, as there are only 8 valid
power curve entries on the eeprom. The former 10 reads lead to
equal max power limits per rate and this causes an increasing
distortion for all rates above 24 MBit and leads to a needless
poor performance in 802.11a mode.
Signed-off-by: NThomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Lockdep found an inconsistent lock state when joining a mesh with
ath5k.  The problem is that ath5k takes the lock for its beacon state,
ah->block, with spin_lock_irqsave(), while mesh internally takes the
sync_offset_lock with spin_lock_bh() in mesh_sync_offset_adjust_tbtt(),
which in turn is called under ah->block.

This could deadlock if the beacon tasklet was run on the processor
that held the beacon lock during the do_softirq() in spin_unlock_bh().

We probably shouldn't hold the lock around the callbacks, but the
easiest fix is to switch to spin_lock_bh for ah->block: it doesn't
need interrupts disabled anyway as the data in question is only accessed
in softirq or process context.

Fixes the following lockdep warning:

[  446.892304] WARNING: at kernel/softirq.c:159 _local_bh_enable_ip+0x38/0xa6()
[  446.892306] Hardware name: MacBook1,1
[  446.892309] Modules linked in: tcp_lp fuse sunrpc cpufreq_ondemand acpi_cpufreq mperf ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 nf_conntrack_ipv4 ip6table_filter nf_defrag_ipv4 xt_state nf_conntrack ip6_tables ext2 arc4 btusb bluetooth snd_hda_codec_idt snd_hda_intel carl9170 snd_hda_codec coretemp joydev ath5k snd_hwdep snd_seq isight_firmware ath snd_seq_device snd_pcm applesmc appletouch mac80211 input_polldev snd_timer microcode cfg80211 snd lpc_ich pcspkr i2c_i801 mfd_core soundcore rfkill snd_page_alloc sky2 tpm_infineon virtio_net kvm_intel kvm i915 drm_kms_helper drm i2c_algo_bit i2c_core video
[  446.892385] Pid: 1892, comm: iw Not tainted 3.6.0-rc1-wl+ #296
[  446.892387] Call Trace:
[  446.892394]  [<c0432958>] warn_slowpath_common+0x7c/0x91
[  446.892398]  [<c04399d7>] ? _local_bh_enable_ip+0x38/0xa6
[  446.892403]  [<c04399d7>] ? _local_bh_enable_ip+0x38/0xa6
[  446.892459]  [<f7f9ae3b>] ? mesh_sync_offset_adjust_tbtt+0x95/0x99 [mac80211]
[  446.892464]  [<c043298f>] warn_slowpath_null+0x22/0x24
[  446.892468]  [<c04399d7>] _local_bh_enable_ip+0x38/0xa6
[  446.892473]  [<c0439a52>] local_bh_enable_ip+0xd/0xf
[  446.892479]  [<c088004f>] _raw_spin_unlock_bh+0x34/0x37
[  446.892527]  [<f7f9ae3b>] mesh_sync_offset_adjust_tbtt+0x95/0x99 [mac80211]
[  446.892569]  [<f7f7650f>] ieee80211_beacon_get_tim+0x28f/0x4e0 [mac80211]
[  446.892575]  [<c047ceeb>] ? trace_hardirqs_on_caller+0x10e/0x13f
[  446.892591]  [<f7fdc541>] ath5k_beacon_update+0x40/0x26b [ath5k]
[  446.892597]  [<c047ad67>] ? lock_acquired+0x1f5/0x21e
[  446.892612]  [<f7fdf9fb>] ? ath5k_bss_info_changed+0x167/0x1b2 [ath5k]
[  446.892617]  [<c087f9ea>] ? _raw_spin_lock_irqsave+0x78/0x82
[  446.892632]  [<f7fdf9fb>] ? ath5k_bss_info_changed+0x167/0x1b2 [ath5k]
[  446.892647]  [<f7fdfa09>] ath5k_bss_info_changed+0x175/0x1b2 [ath5k]
[  446.892651]  [<c0479dd4>] ? lock_is_held+0x73/0x7b
[  446.892662]  [<c0458fd5>] ? __might_sleep+0xa7/0x17a
[  446.892698]  [<f7f5d8f7>] ieee80211_bss_info_change_notify+0x1ed/0x21a [mac80211]
[  446.892703]  [<c0449875>] ? queue_work+0x24/0x32
[  446.892718]  [<f7fdf894>] ? ath5k_configure_filter+0x163/0x163 [ath5k]
[  446.892766]  [<f7f95fa4>] ieee80211_start_mesh+0xb9/0xbd [mac80211]
[  446.892806]  [<f7f6e610>] ieee80211_join_mesh+0x10c/0x116 [mac80211]
[  446.892834]  [<f7a96b90>] __cfg80211_join_mesh+0x176/0x1b3 [cfg80211]
[  446.892855]  [<f7a96c1c>] cfg80211_join_mesh+0x4f/0x6a [cfg80211]
[  446.892875]  [<f7a89891>] nl80211_join_mesh+0x1de/0x1ed [cfg80211]
[  446.892908]  [<f7a8db99>] ? nl80211_set_wiphy+0x4cf/0x4cf [cfg80211]
[  446.892919]  [<c07cfa36>] genl_rcv_msg+0x1d5/0x1f3
[  446.892940]  [<c07cf861>] ? genl_rcv+0x25/0x25
[  446.892946]  [<c07cf009>] netlink_rcv_skb+0x37/0x78
[  446.892950]  [<c07cf85a>] genl_rcv+0x1e/0x25
[  446.892955]  [<c07cebf3>] netlink_unicast+0xc3/0x12d
[  446.892959]  [<c07cee46>] netlink_sendmsg+0x1e9/0x213
[  446.892966]  [<c079f282>] sock_sendmsg+0x79/0x96
[  446.892972]  [<c04eb90d>] ? might_fault+0x9d/0xa3
[  446.892978]  [<c07a81d8>] ? copy_from_user+0x8/0xa
[  446.892983]  [<c07a852c>] ? verify_iovec+0x43/0x77
[  446.892987]  [<c079f4d8>] __sys_sendmsg+0x180/0x215
[  446.892993]  [<c045f107>] ? sched_clock_cpu+0x134/0x144
[  446.892997]  [<c047992f>] ? trace_hardirqs_off+0xb/0xd
[  446.893002]  [<c047bf88>] ? __lock_acquire+0x46b/0xb6e
[  446.893006]  [<c047992f>] ? trace_hardirqs_off+0xb/0xd
[  446.893010]  [<c045f149>] ? local_clock+0x32/0x49
[  446.893015]  [<c0479ec1>] ? lock_release_holdtime.part.9+0x4b/0x51
[  446.893020]  [<c0479dd4>] ? lock_is_held+0x73/0x7b
[  446.893025]  [<c050d127>] ? fcheck_files+0x97/0xcd
[  446.893029]  [<c050d4df>] ? fget_light+0x2d/0x81
[  446.893034]  [<c07a01f3>] sys_sendmsg+0x3b/0x52
[  446.893038]  [<c07a07b4>] sys_socketcall+0x238/0x2a2
[  446.893044]  [<c0885edf>] sysenter_do_call+0x12/0x38
[  446.893047] ---[ end trace a9af5998f929270f ]---
[  447.627222]
[  447.627232] =================================
[  447.627237] [ INFO: inconsistent lock state ]
[  447.627244] 3.6.0-rc1-wl+ #296 Tainted: G        W
[  447.627248] ---------------------------------
[  447.627253] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[  447.627260] swapper/0/0 [HC0[0]:SC1[1]:HE1:SE0] takes:
[  447.627264]  (&(&ah->block)->rlock){+.?...}, at: [<f7fdd2d1>] ath5k_tasklet_beacon+0x91/0xa7 [ath5k]
[  447.627299] {SOFTIRQ-ON-W} state was registered at:
[  447.627304]   [<c047cdbf>] mark_held_locks+0x59/0x77
[  447.627316]   [<c047ceeb>] trace_hardirqs_on_caller+0x10e/0x13f
[  447.627324]   [<c047cf27>] trace_hardirqs_on+0xb/0xd
[  447.627332]   [<c0439a3d>] _local_bh_enable_ip+0x9e/0xa6
[  447.627342]   [<c0439a52>] local_bh_enable_ip+0xd/0xf
[  447.627349]   [<c088004f>] _raw_spin_unlock_bh+0x34/0x37
[  447.627359]   [<f7f9ae3b>] mesh_sync_offset_adjust_tbtt+0x95/0x99 [mac80211]
[  447.627451]   [<f7f7650f>] ieee80211_beacon_get_tim+0x28f/0x4e0 [mac80211]
[  447.627526]   [<f7fdc541>] ath5k_beacon_update+0x40/0x26b [ath5k]
[  447.627547]   [<f7fdfa09>] ath5k_bss_info_changed+0x175/0x1b2 [ath5k]
[  447.627569]   [<f7f5d8f7>] ieee80211_bss_info_change_notify+0x1ed/0x21a [mac80211]
[  447.627628]   [<f7f95fa4>] ieee80211_start_mesh+0xb9/0xbd [mac80211]
[  447.627712]   [<f7f6e610>] ieee80211_join_mesh+0x10c/0x116 [mac80211]
[  447.627782]   [<f7a96b90>] __cfg80211_join_mesh+0x176/0x1b3 [cfg80211]
[  447.627816]   [<f7a96c1c>] cfg80211_join_mesh+0x4f/0x6a [cfg80211]
[  447.627845]   [<f7a89891>] nl80211_join_mesh+0x1de/0x1ed [cfg80211]
[  447.627872]   [<c07cfa36>] genl_rcv_msg+0x1d5/0x1f3
[  447.627881]   [<c07cf009>] netlink_rcv_skb+0x37/0x78
[  447.627891]   [<c07cf85a>] genl_rcv+0x1e/0x25
[  447.627898]   [<c07cebf3>] netlink_unicast+0xc3/0x12d
[  447.627907]   [<c07cee46>] netlink_sendmsg+0x1e9/0x213
[  447.627915]   [<c079f282>] sock_sendmsg+0x79/0x96
[  447.627926]   [<c079f4d8>] __sys_sendmsg+0x180/0x215
[  447.627934]   [<c07a01f3>] sys_sendmsg+0x3b/0x52
[  447.627941]   [<c07a07b4>] sys_socketcall+0x238/0x2a2
[  447.627949]   [<c0885edf>] sysenter_do_call+0x12/0x38
[  447.627959] irq event stamp: 1929200
[  447.627963] hardirqs last  enabled at (1929200): [<c043a0e9>] tasklet_hi_action+0x3e/0xbf
[  447.627972] hardirqs last disabled at (1929199): [<c043a0c0>] tasklet_hi_action+0x15/0xbf
[  447.627981] softirqs last  enabled at (1929196): [<c043999d>] _local_bh_enable+0x12/0x14
[  447.627989] softirqs last disabled at (1929197): [<c040443b>] do_softirq+0x63/0xb8
[  447.627999]
[  447.627999] other info that might help us debug this:
[  447.628004]  Possible unsafe locking scenario:
[  447.628004]
[  447.628009]        CPU0
[  447.628012]        ----
[  447.628016]   lock(&(&ah->block)->rlock);
[  447.628023]   <Interrupt>
[  447.628027]     lock(&(&ah->block)->rlock);
[  447.628034]
[  447.628034]  *** DEADLOCK ***
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath_rx_tasklet() calls ath9k_rx_skb_preprocess() and ath9k_rx_skb_postprocess()
in a loop over the received frames. The decrypt_error flag is
initialized to false
just outside ath_rx_tasklet() loop. ath9k_rx_accept(), called by
ath9k_rx_skb_preprocess(),
only sets decrypt_error to true and never to false.
Then ath_rx_tasklet() calls ath9k_rx_skb_postprocess() and passes
decrypt_error to it.
So, after a decryption error, in ath9k_rx_skb_postprocess(), we can
have a leftover value
from another processed frame. In that case, the frame will not be marked with
RX_FLAG_DECRYPTED even if it is decrypted correctly.
When using CCMP encryption this issue can lead to connection stuck
because of CCMP
PN corruption and a waste of CPU time since mac80211 tries to decrypt an already
deciphered frame with ieee80211_aes_ccm_decrypt.
Fix the issue initializing decrypt_error flag at the begging of the
ath_rx_tasklet() loop.
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During suspend, the device will be moved to FULLSLEEP state.
As btcoex is never been stopped, the btcoex timer is running
and tries to access hw on fullsleep state. Fix that.

Cc: stable@vger.kernel.org
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This return holds the number of bytes transfered (1 byte) or a negative
error code.  The type should be int instead of u8.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Do not leak memory by updating pointer with potentially NULL realloc return value.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

commit b74713d0
"ath9k: Handle fatal interrupts properly" introduced a race condition, where
IRQs are being left enabled, however the irq handler returns IRQ_HANDLED
while the reset is still queued without addressing the IRQ cause.
This leads to an IRQ storm that prevents the system from even getting to
the reset code.

Fix this by disabling IRQs in the handler without touching intr_ref_cnt.

Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's a bug that causes the rate scaling to get stuck
when it has to use single-stream rates with a peer that
can do GF and SGI; the two are incompatible so we can't
use them together, but that causes the algorithm to not
work at all, it always rejects updates.

Disable greenfield for now to prevent that problem.

Cc: stable@vger.kernel.org
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Tested-by: NCesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We can not pass NULL libconf->conf->channel to rt61pci_config() as it
is dereferenced unconditionally in rt61pci_config_lna_gain() subroutine.

Resolves:
https://bugzilla.kernel.org/show_bug.cgi?id=44361

Cc: stable@vger.kernel.org
Reported-and-tested-by: <dolohow@gmail.com>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR1111 is same as AR9485. The h/w
difference between them is quite insignificant,
Felix suggests only very few baseband features
may not be available in AR1111. The h/w code for
AR9485 is already present, so AR1111 should
work fine with the addition of its PID/VID.

Cc: stable@vger.kernel.org [2.6.39+]
Cc: Felix Bitterli <felixb@qca.qualcomm.com>
Reported-by: NTim Bentley <Tim.Bentley@Gmail.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Tested-by: NTim Bentley <Tim.Bentley@Gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

brcmsmac cannot call freq_reg_info() during channel changes as it does
not hold cfg80211_lock, and as a result it generates a lockdep warning.
freq_reg_info() is being used to determine whether OFDM is allowed on
the current channel, so we can avoid the errant call by using the new
IEEE80211_CHAN_NO_OFDM for this purpose instead.
Reported-by: NJosh Boyer <jwboyer@redhat.com>
Signed-off-by: NSeth Forshee <seth.forshee@canonical.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The if_sdio_card structure was never being freed, and neither
was the command structure used for association.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch is going to fix the resuming failed from S3/S4
for rt3290 chip.
Signed-off-by: NWoody Hung <Woody.Hung@mediatek.com>
Cc: Kevin Chou <kevin.chou@mediatek.com>
Signed-off-by: NChen, Chien-Chia <machen@suse.com>
Reviewed-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On an OLPC XO-1.5 we have seen the following situation:
 - the system starts going into suspend
 - no wake params are set, so the mmc layer removes the card
 - during remove, we send a command to the card
 - that command fails, causing if_sdio's reset method to try and remove
   the mmc card in attempt to reset it
 - the mmc layer is not happy about being asked to remove a card that
   it is already removing, and the kernel crashes

While the MMC layer could possibly be taught to behave better here,
it also seems sensible for libertas not to try and reset a card if
we're in the process of removing it anyway.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add some comments by the way
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In bnx2x_mcast_enqueue_cmd() we'll leak the memory allocated to
'new_cmd' if we hit the deafault case of the 'switch (cmd)'.
Add a 'kfree(new_cmd)' to that case to avoid the leak.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Acked-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently an skb requiring TSO may not fit within a minimum-size TX
queue.  The TX queue selected for the skb may stall and trigger the TX
watchdog repeatedly (since the problem skb will be retried after the
TX reset).  This issue is designated as CVE-2012-3412.

Set the maximum number of TSO segments for our devices to 100.  This
should make no difference to behaviour unless the actual MSS is less
than about 700.  Increase the minimum TX queue size accordingly to
allow for 2 worst-case skbs, so that there will definitely be space
to add an skb after we wake a queue.

To avoid invalidating existing configurations, change
efx_ethtool_set_ringparam() to fix up values that are too small rather
than returning -EINVAL.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The skb->pfmemalloc flag gets set to true iff during the slab allocation
of data in __alloc_skb that the the PFMEMALLOC reserves were used.  If
page splitting is used, it is possible that pages will be allocated from
the PFMEMALLOC reserve without propagating this information to the skb.
This patch propagates page->pfmemalloc from pages allocated for fragments
to the skb.

It works by reintroducing and expanding the skb_alloc_page() API to take
an skb.  If the page was allocated from pfmemalloc reserves, it is
automatically copied.  If the driver allocates the page before the skb, it
should call skb_propagate_pfmemalloc() after the skb is allocated to
ensure the flag is copied properly.

Failure to do so is not critical.  The resulting driver may perform slower
if it is used for swap-over-NBD or swap-over-NFS but it should not result
in failure.

[davem@davemloft.net: API rename and consistency]
Signed-off-by: NMel Gorman <mgorman@suse.de>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Cc: Neil Brown <neilb@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With addition of dummy clk_*() calls for non CONFIG_HAVE_CLK cases in
clk.h, there is no need to have clk code enclosed in #ifdef
CONFIG_HAVE_CLK, #endif macros.

This also fixes error paths of probe(), as a goto is required in this
patch.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: viresh kumar <viresh.linux@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With addition of dummy clk_*() calls for non CONFIG_HAVE_CLK cases in clk.h,
there is no need to have clk code enclosed in #ifdef CONFIG_HAVE_CLK, #endif
macros.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Cc: Bhupesh Sharma <bhupesh.sharma@st.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: viresh kumar <viresh.linux@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tun module leaks up to 36 bytes of memory by not fully initializing
a structure located on the stack that gets copied to user memory by the
TUNGETIFF and SIOCGIFHWADDR ioctl()s.
Signed-off-by: NMathias Krause <minipli@googlemail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Spinlock should be taken before checking for tp->hw_stats.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After Power-on-reset, the 5719's TX DMA length registers may contain
uninitialized values and cause TX DMA to stall.  Check for invalid
values and set a register bit to flush the TX channels.  The bit
needs to be turned off after the DMA channels have been flushed.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The workaround was mis-applied to all 5719 and 5720 chips.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

to prevent PHY access conflict with APE firmware.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

the driver sees wether the dev_seeq pointer is having a error that can be
read by using the PTR_ERR, and returns it at error case, other wise 0 at
success case.

the PTR_RET does the same thing, and use PTR_RET instead of redoing the
code of PTR_RET
Signed-off-by: NDevendra Naga <develkernel412222@gmail.com>
Acked-by: NDavid Howells <dhowells@redhat.com>
Reviewed-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

casting the void pointer is redundant (Documentation/CodingStyle)
Signed-off-by: NDevendra Naga <develkernel412222@gmail.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fills the net_device vlan_features with the proper hardware features,
thus, improving the vlan interface performance.

With the patch applied, I can see around 148% improvement on a TCP_STREAM test,
from 3.5 Gb/s to 8.7 Gb/s. On TCP_RR, I see a 11% improvement, from 18k
to 20. The CPU utilization is almost the same on both cases, from the comparison
above.
Signed-off-by: NBreno Leitao <brenohl@br.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>