This patch updates the PCI power save handling
code, fixing ASPM hangs and handling device state D3
properly.

The WAR register is programmed with the correct
values now.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Add a few comments, and move the updation of max_power_level
  to a helper routine. This is also done by non-4K based chipsets,
  this will be fixed in a separate patch.

* Remove two WARs which are required for old AR5416 chipsets,
  and are not needed for AR9287.

* Fix indentation and make things readable.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rather than doing a series of RMWs, calculate the
value to be written to the register in question and
do a single REGWRITE. This improves bringup time.

This depends on the analog_shiftreg configuration option,
which is currently buggy. For AP mode, a delay of 100us
has to be the default. For station mode, this knob has to
be enabled on a per-case basis, though it is a little
unclear on when to enable a delay. This can be fixed later though.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Fix whitespace damage.
* Remove unused debug messages.
* Introduce a macro NUM_EEP_WORDS.
* Convert AR9287 to lowercase in function names.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch replaces the buggy 'ath9k: Group Key fix for VAPs' change.

For AP mode group keys, use the BSSID as lookup mac address, with
the multicast keysearch bit set.
For IBSS mode, use the peer's MAC address with multicast keysearch.
For STA mode, keep using the group key slots.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If a MAC address for a key table entry is flagged with the
multicast bit (0x01), indicate to the hardware that multicast
lookup instead of unicast lookup should be used. The multicast
bit itself never makes it to the actual keytable entry register,
as it is shifted out.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We dereference "wmi" on the line before and also when we initialize "ah".
This check has always been after a dereference since the first commit a
couple months ago.  Looking through the code, it looks like "wmi" can't
actually be null here so I just removed the check.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The rx status length should also be taken into account while
validating the length of a received frame.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Skip the rx status portion in skb->data before accessing ieee80211
frame header.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k_rx_skb_preprocess() needs only ieee80211 frame header,
pass only frame headers instead of skb to that function. Also
remove ineffective frame dump in ath9k_process_rate().
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A bunch of data structures are present in the
common module, which are internal to ath9k.
Move them to ath9k.h
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch relocates RX processing code from the
common module to ath9k. This reduces the size
of the common module which is also used by ath9k_htc.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To enable it we now disable and re-enable the PHY chips
after TX IQ calibration.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since we have sysfs to manually set the ANI levels, we should print errors to
the kernel log if the values are out of bounds.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Calculate 'listen' time also when automatic ANI is off, since this and the
"busy" time is useful information also in manual mode.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

/sys/class/ieee80211/phy0/device/ani/ani_mode
/sys/class/ieee80211/phy0/device/ani/noise_immunity_level
/sys/class/ieee80211/phy0/device/ani/spur_level
/sys/class/ieee80211/phy0/device/ani/firstep_level
/sys/class/ieee80211/phy0/device/ani/ofdm_weak_signal_detection
/sys/class/ieee80211/phy0/device/ani/cck_weak_signal_detection
/sys/class/ieee80211/phy0/device/ani/noise_immunity_level_max
/sys/class/ieee80211/phy0/device/ani/spur_level_max
/sys/class/ieee80211/phy0/device/ani/firstep_level_max

sysfs has a lot of symlinks, so you can find the files also in other locations,
like (by PCI ID) /sys/devices/pci0000:00/0000:00:11.0/ani and others.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It's our "private driver data"... It's used more often and hw is the mac80211
part. This makes more sense with the next (sysfs) patch.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The old code logically did not make sense and seems to have been confused by
the fact that we could have newer EEPROMs on older hardware. In any case the
spur mitigation filter was set if the srev was >= AR5K_SREV_AR5424.

Spur info is available only from EEPROM versions bigger than 5.3 but but the
EEPOM routines will use static values for older versions, so that should be
o.k.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now that we have ftrace, it is not needed any more.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since NF calibration interferes with TX and RX and also has been the cause of
other problems (when it's run concurrently with ath5k_reset) we want to run it
less often - every 60 seconds for now.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As far as we know, only NF calibration interferes with RX/TX so we can
leave the queues enabled for the other calibrations.

BTW: Stopping the queues is not enough for avoiding transmissions, since there
might be packets in the queue + beacons are also sent regularly! But i leave it
like this until we have a better solution (stopping TX DMA?).
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Seperate noise floor calibration from other PHY calibration and move it to the
tasklet. This is the first step to more separation of different calibrations.

Also move out ath5k_hw_request_rfgain_probe(ah) so we have one clean function
for I/Q calibration on 5111x parts.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Initialize calibration timers on reset, since otherwise they might be in the
future and the calibration tasklet might not be scheduled for a long time.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rx should not be disabed/disabled when hw supports auto sleeping.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add missing code to handle nullfunc frame completion in
ath_tx_edma_tasklet().
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NWalter Goldens <goldenstranger@yahoo.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use BSS_CHANGED_HT to handle HT parameter changes.
The rate information on the target has to be updated
to handle changes in HT configuration.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes a large chunk of code dealing
with rate management within the driver and simplifying
things by removing the hacky method of calculating
HT changes. A subsequent patch would fix this by
just using BSS_CHANGED_HT from mac80211.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update from internal systems engineering team.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use kmemdup when some other buffer is immediately copied into the
allocated region.

A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression from,to,size,flag;
statement S;
@@

-  to = \(kmalloc\|kzalloc\)(size,flag);
+  to = kmemdup(from,size,flag);
   if (to==NULL || ...) S
-  memcpy(to, from, size);
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Changed -EINVAL to -EFAULT if copy_to_user() failed.
Changed 0 to -ENOMEM if allocations failed.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The snprintf() function returns the number of bytes that *would* have
been written (not counting the NULL terminator) and that can potentally
be more than the size of the buffer.

In this patch if there were one liners where string clearly fits into
the buffer, then I changed snprintf to sprintf().  It's confusing to use
the return value of snprintf() as a limitter without verifying that it's
smaller than size.  This is what initially caught my attention here.
If we use the return value of sprintf() instead future code auditors will
assume we've verified that it fits already.

Also I did find some places where it made sense to use the return value
after we've verified that it is smaller than the buffer size.

Finally the read_file_rcstat() function added an explicit NULL terminator
before calling snprintf().  That's unnecessary because snprintf() will
add the null terminator automatically.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For edma, we should use DMA_BIDIRECTIONAL, or else use
DMA_FROM_DEVICE.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is the maximum supported by the firmware.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no need to determine the HW queue
for each packet that is transmitted. The endpoint
can be chosen directly based on the queue type
that mac80211 sends down.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>