This seems to be relatively stable now, so enable it for these chipsets
too.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The vblank interrupt on r600 doesn't seem to be especially reliable, so
perform some sanity checks before the actual reclock.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The ttm code could take vram_mutex followed by cp_mutex, while the
reclocking code would do the reverse. Hilarity could ensue.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

We need to choose the correct PM state to transition into before starting
the actual change. Call radeon_get_power_state() at the top of the clock
setting to do so.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

With luck, dynamic memory reclocking on r600 should be stable with
the previous patches. Enable it.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The ttm bo workqueue may touch objects while we're reclocking, so make
sure it's blocked until we're done.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

We need to block the drm core from doing anything that may touch our vram
during reclock, so take the drm mutex for the duration.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Touching vram while the card is reclocking can lead to lockups. Unmap
any pages that could be touched by the CPU and block any accesses to
vram until the reclocking is complete.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

There's a moderate amount of effort involved in setting the card up for
clock transitions, so unify the codepaths to make it easier to implement.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Add two new sysfs attributes:
- dynpm
- power_state

Echoing 0/1 to dynpm disables/enables dynamic power management.
The driver scales the sclk dynamically based on the number of
queued fences.  dynpm only scales sclk dynamically in single head
mode.

Echoing x.y to power_state selects a static power state (x) and clock
mode (y).  This allows you to statically select a power state and clock
mode.  Selecting a static clock mode will disable dynpm.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- pm_misc() - handles voltage, pcie lanes, and other non
clock related power mode settings.  Currently disabled.
Needs further debugging

- pm_prepare() - disables crtc mem requests right now.
All memory clients need to be disabled when changing
memory clocks.  This function can be expanded to include
disabling fb access as well.

- pm_finish() - enable active memory clients.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- remove non_clock_info struct
- track power state misc flags
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Just adds overhead when the power state will never change.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Hook the atom table parsing up to module loading, so we can automatically
load the appropriate hwmon drivers.

Based on initial patch for r6xx from Matthew Garrett
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This also simplifies the code and enables reclocking with multiple heads
active by tracking whether the power states are single or multi-head
capable.

Eventually, we will want to select a power state based on external
factors (AC/DC state, user selection, etc.).

(v2) Update for evergreen
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

(v2) Add evergreen vbl checks
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

crtcs are what we ultimately care about wrt to pm.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

On pre-r6xx, the power mode array is usually ordered:
low
...
high
default

On r6xx+:
default
low
...
high
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

set proper wait condition as noted by Rafał Miłecki.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Useful for certain power management operations.  You
need to wait for the GUI engine (2D, 3D, CP, etc.) to be
idle before changing clocks or adjusting engine parameters.

(v2) Fix gui idle enable on pre-r6xx asics

(v3) The gui idle interrrupt status bit is permanently asserted
on pre-r6xx chips, but the interrrupt is still generated.
workaround it in the driver.

(v4) Add support for evergreen
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Check to see if the GUI engine and related blocks
(2D, 3D, CP, etc) are idle or not.  There are a number
of cases when we need to know if the drawing engine
is busy.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

After thinking it over a lot it made more sense for the core to deal with
the output polling especially so it can notify X.

v2: drop plans for fake connector - per Michel's comments - fix X patch sent to xorg-devel, add intel polled/hpd setting, add initial nouveau polled/hpd settings.

v3: add config lock take inside polling, add intel/nouveau poll init/fini calls

v4: config lock was a bit agressive, only needed around connector list reading.
otherwise it could re-enter.

glisse: discard drm_helper_hpd_irq_event

v3: Reviewed-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

It removes a hack from nouveau code which had to detect which
region to pass to kick vesafb/efifb.
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Userspace need to know the hw crtc id (0, 1, 2, ...) from the drm
crtc id. Bump the minor version so userspace can enable conditionaly
features depend on this.

V2 use num_crtc and avoid DRM_ERROR
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Use kmemdup when some other buffer is immediately copied into the
allocated region.

A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression from,to,size,flag;
statement S;
@@

-  to = \(kmalloc\|kzalloc\)(size,flag);
+  to = kmemdup(from,size,flag);
   if (to==NULL || ...) S
-  memcpy(to, from, size);
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Should work better on some panels.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Fixes LVDS issues on some laptops; notably laptops with
2048x1536 panels.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Previously we just set them to dpms off.  This should save
additional power.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Previous reset code leaded to computer hard lockup (need to unplug
the power too reboot the computer) on various configuration. This
patch change the reset code to avoid hard lockup. The GPU reset
is failing most of the time but at least user can log in remotely
or properly shutdown the computer.

Two issues were leading to hard lockup :
- Writting to the scratch register lead to hard lockup most likely
because the write back mecanism is in fuzy state after GPU lockup.
- Resetting the GPU memory controller and not reinitializing it
after leaded to hard lockup. We did only reinitialize in case of
successfull reset thus unsuccessfull reset quickly leaded to hard
lockup.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Implements irq support for HDMI audio output. Now the polling timer
is only enabled if irq support isn't available.
Signed-off-by: NChristian König <deathsimple@vodafone.de>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Rework HDMI audio polling timer, only enable it when
at least one HDMI encoder needs it. Preparation for
replacing it with irq support.
Signed-off-by: NChristian König <deathsimple@vodafone.de>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This patch enable the use of unmappable VRAM thanks to
previous TTM infrastructure change.

V2 update after io_mem_reserve/io_mem_free callback balancing
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

All TTM driver have been converted to new io_mem_reserve/free
interface which allow driver to choose and return proper io
base, offset to core TTM for ioremapping if necessary. This
patch remove what is now deadcode.

V2 adapt to match with change in first patch of the patchset
V3 update after io_mem_reserve/io_mem_free callback balancing
V4 adjust to minor cleanup
V5 remove the needs ioremap flag
V6 keep the ioremapping facility in TTM

[airlied- squashed driver removals in here also]
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Reviewed-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This add the support for the new fault callback and also the
infrastructure for supporting unmappable VRAM.

V2 validate BO with no_wait = true
V3 don't derefence bo->mem.mm_node as it's not NULL only for
   VRAM or GTT
V4 update to splitted no_wait ttm change
V5 update to new balanced io_mem_reserve/free change
V6 callback is responsible for iomapping memory
V7 move back iomapping to ttm
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

When drivers embed the core gem object into their own structures,
they'll have to do this. Temporarily this results in an ugly

kfree(gem_obj);

in every gem driver.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>