Add SD Card support to the kfr2r09 board using the
sh_mobile_sdhi driver hooked up to SDHI0 and yc304.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Switch to using both register sets - side A and side B for display panning.
Signed-off-by: NPhil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Fix the kfr2r09 board code so it compiles if CONFIG_I2C=n.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add USB gadget support for port YC301 on the KFR2R09 board.

The r8a66597-udc driver is hooked up as a platform device,
clocks are enabled via I2C and some registers are configured
to enable the USB in gadget mode. The hardware driving the
USB port is the on-chip USB0 block in the sh7724 processor
configured as USB gadget controller.

This board is using external hardware to detect USB hotplug
events and allows the processor to dynamically start and stop
clocks. This well thought out hardware feature is unused at
this point and plug and play is unfortunately unsupported.
To properly support all hardware features the USB gadget
stack may need some adjustment.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch simply adds LCDC hwblk_id data for the kfr2r09 board.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds support for the NAND flash chip
attached to CS4 on the KFR2R09 board. The device is
driven by the platform device driver "onenand-flash".
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds support for the WQVGA LCD display used by
the KFR2R09 board. The LCD module is a TX07D34VM0AAA made
by Hitachi, and this module is made up by a R61517 chip
together with a 240x400 pixel display. The screen is
attached to the SuperH Mobile LCDC using a 18-bit SYS bus.

The register settings used by the SYS panel setup code are
based on an out-of-tree driver which apart from duplicating
all LCDC driver code and writing to non-existing hardware
registers also never was posted for upstream merge.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add hwblk_id to kfr2r09 board specific on-chip sh7724
platform devices.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds KEYSC keypad support to the kfr2r09 board.

The keys driven by the sh7724 on-chip KEYSC block are
described as a platform device and platform data for
the sh_keysc driver.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds NOR flash support to the kfr2r09 board.

NOR flash support is added by describing the NOR flash
chip hooked up to CS0 as platform device data for the
physmap-flash MTD driver.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds basic kfr2r09 board support. Only
the SCIF1 console is supported with this patch, but
this patch and a proper sh7724 configuration is all
that is needed. Combine with an initramfs to have a
small RAM based kernel and distribution booted as
zImage from RAM via JTAG.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>