In case of ep_disable and reset interrupt is received and, still there
was at least one request queued for dma transfer, then endpoint is
stopped first. Once endpoint is stopped, callback for all queued
request must be called.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

It is needed to enumerate recent cores like 2.10a.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The definition of DWC3_DCTL_HIRD_THRES macro is
completely wrong. It will only work for when we
want to read the register's contents for that bitfield.

Change the macro so that it can be used to writing to
the register, and when we need to read, we can add
extra right shift of 24 bits.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>

[ balbi@ti.com: add a commit log ]
Signed-off-by: NFelipe Balbi <balbi@ti.com>

By the time we're disabling the endpoint, HW
could already have posted more events to our
event buffer. In that case, we will receive
endpoint events for a disabled endpoint.

In order to protect ourselves from that situation,
we simply ignore endpoint interrupts whenever
the endpoint is disabled.
Tested-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In case we get disconnected, we will call gadget
driver's disconnect method, which should make
sure to disable all endpoints. At that point
we will call stop_active_transfers() to make
sure we didn't leave any pending request on the
controller.
Tested-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

That IRQ is causing way too much trouble. We have
a different handling which was agreed with IP
provider and has been tested with FPGA and OMAP5.
Tested-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We never set CMDIOC bit for Start Transfer
command, so that code will never be used.
Tested-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If event status says that its last completed TRB but TRB is still owned
by HW then break from the loop, because we are not going to get correct
TRB status from trb control/size register.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If an IN transfer is missed on isoc endpoint, then driver must insure
that next ep_queue is properly handled.
This patch fixes this issue by starting a new transfer for next queued
request.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

SOF Number is bit16:3 of DSTS. Correct the mask accordingly.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Correct  define for DWC3_TRB_SIZE_TRBSTS.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Currently in case of isoc, interrupt is programmed after each
TRB_NUM/4 ie 8th TRB. A TRB is programmed against each submitted
request from gadget. If we do not want to limit the minimum number of
necessary request to be submitted from gadget then we must receive
interrupt on each TRB submission. There can be such situation with a
gadget working with ping-pong buffer.

If a gadget does not want to receive interrupt after each request
completion then it may set no_interrupt flag.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

That's a much more intuitive name as that function
is only called at the completion of a Status Phase.

It also matches dwc3_ep0_complete_data() for
the completion of Data Phase.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

USB is always little endian, but this driver
could run on non little endian cpus. Let's
be carefull with that.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There's no need for returning early. Instead,
we can call dwc3_ep0_stall_and_restart()
conditionally.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

According to the databook, the DWC3 Core will
reset those bits to 0 on USB Bus Reset. This
means we must re-enable those bits on every
reset interrupt.

Because we will always get a Reset interrupt
after loading a gadget driver, we can, instead
of re-enabling something that was just lost,
move the handling of those bits to the Reset
Interrupt.

This patch fixes USB30CV U1/U2 Test.
Signed-off-by: NGerard CAUVY <g-cauvy1@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If we get a disconnect IRQ, we should take
the core out of low power mode so we can
reconnect afterwards.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If we don't read out the contents of the register
(in order to reinitialize 'reg' variable) we will
be writing unknown contents to the DCTL register
whenever we try to use dwc3_gadget_wakeup() function.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The same event buffers will be reused when coming
out of hibernation, so we must reinitialize them
properly to avoid any mistakes.

While at that, also take dwc3_event_buffers_setup()
out of __devinit section.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Recent cores (>= 1.94a) have a set of new features,
commands and a slightly different programming model.

This patch aims to support those changes.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

those two functions don't power PHYs, they simply
put them in suspend state. Rename to reflect better
what functions actually do.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

retries is used twice without being reinitialized.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch adds definitions for some new registers that have been
added to later versions of the controller, up to v2.10a.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

That semicolon doesn't do anything, it's not
needed and should be removed.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

s/has/have. No functional changes, just
a typo fix on a code comment.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

On our Transfer Not Ready handlers, only
dwc3_ep0_do_control_status() had a different
list of parameters.

Align on the parameters in order to keep consistency.

No functional changes.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

IS_ALIGNED provides a much faster operation for
checking proper size alignment then a modulo
operation. Let's use it.
Reported-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When DWC3_EP_PENDING_REQUEST flag is set for a Control OUT Data
phase transfer, we would be missing the proper handling for
unaligned OUT requests, thus hanging a transfer.

Since proper handling is already done on dwc3_ep0_do_control_data(),
we simply re-factor that function so it can be re-used from
__dwc3_gadget_ep0_queue().
Reported-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

we're now have DWC3_EP0_BOUNCE_SIZE to tell
us the actual size of the bufer. Let's use that
instead of ep0 wMaxPacketSize.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The warning shown up when ran with randconfig,

warning: (USB_DWC3) selects USB_XHCI_PLATFORM which has unmet direct dependencies (USB_SUPPORT && USB_XHCI_HCD)
Signed-off-by: Njoseph daniel <josephdanielwalter@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove redundant pointer to struct usb_endpoint_descriptor.
Signed-off-by: NIdo Shayevitz <idos@codeaurora.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

to avoid sprinkling magic constants on the driver
we define a constant to be used when allocating
setup_buffer and ep0_bounce buffer.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Issue an Update Transfer command after queuing a request to an isoc
EP with an active transfer. This is required according to the dwc3
databook. Pratyush Anand reports that this fixes a problem he was
having with Isoc IN transfers.

Tested-by: Pratyush Anand<pratyush.anand@st.com>
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This is basically a noop for DWC3. We don't have
to do anything. Basically we test if the request
parameters are correct, cache the Isochronous
Delay and return success.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We want to re-use that buffer for other USB
requests, so let's increase it to biggest
wMaxPacketSize for ep0 so it works for everything
we have in mind.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch implements Set SEL Standard Request
support for dwc3 driver. It needs to issue a command
to the controller passing the timing we received on
the data phase of the Set SEL request.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This will be used by the ep0 layer for implementing
Set SEL Standard Request.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

On device loading the driver enables LPM and the acceptance of U1 and U2
states. The [Set|Clear]Feature requests for "U1/U2" are forwarded
directly to the hardware and allow / forbid the initiation of the low
power links.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This fix prevents a problem with dwc3 and host mode where
we were requesting the entire memory region in dwc3/core.c,
thus preventing xhci-plat from ever ioremapping its own address space.
Signed-off-by: NIdo Shayevitz <idos@codeaurora.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We separate between dwc3-omap helper functions to dwc3-core helper
functions. This will allow us to change the helper functions
implementation according to each module need.
Signed-off-by: NIdo Shayevitz <idos@codeaurora.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>