Trivial cleanup for extra_info_update_ongoing(), making the function a
bit cleaner.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Currently dss_write_regs() implicitely sets the GO bits for all managers
with shadow dirty flags set. This is a bit misleading, as one does not
presume "write registers" function to also set the GO bit.

Thus this patch splits the setting of GO bits into a separate function,
dss_set_go_bits, which is used after writing the registers.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In the apply irq handler the code currently clears the shadow dirty
flags whenever the manager in question is not busy (i.e. GO bit is
down). However, this is not quite right, as the GO bit may have never
been set.

While not done in the current code, the above would cause bug in
scenario where the registers are written, and thus shadow_dirty flag is
set, but the GO bit will be set only later. In this case the
shadow_dirty flags would be cleared, even if the HW is not using the new
configurations.

This patch fixes the issue by clearing the shadow flags only when the GO
bit is clear, and the GO bit had been set.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

need_isr() should return true whenever there's work that needs to be
handled in the VSYNC/FRAMEDONE irq handler. However, need_isr() is
missing some cases where we need the irq handler.

This patch adds checks for shadow dirty flags, so that the irq handler
is started/kept running while shadow dirty flags are set.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

extra_info_update_ongoing() skipped checks for overlays that were marked
as disabled. This doesn't work, as the enable status of an overlay is in
the extra_info group, and thus extra_info_update_ongoing() reports false
when we are disabling an overlay. This causes
wait_pending_extra_info_updates() to not wait for the ongoing overlay
disable.

This patch changes extra_info_update_ongoing() to check the state of
overlays marked as disabled.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now that dss_mgr_enable returns an error value, check it in all the
places dss_mgr_enable is used, and bail out properly.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now that dss_mgr_enable() can fail due to checks, make it return the
error value.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add checks for overlay and manager settings. The checks are a bit
complex, as we need to observe the bigger picture instead of overlays
and managers independently. Things like the used display and the zorder
of other overlays affect the validity of the settings.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add dss_mgr_simple_check() which is used to check the validity of
certain manager attributes. Only attributes that can be checked
independently, without knowing the display being used, is done here
(thus "simple").

We can use this function in dss_mgr_set_info().
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add dss_ovl_simple_check() which is used to check the validity of
certain overlay attributes. Only attributes that can be checked
independently, without knowing the display being used, is done here
(thus "simple").

We can use this function in dss_ovl_set_info().
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add comments specifying what ovl/mgr functions may block.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

apply.c no longer touches any registers if an output is not enabled.
This means that we don't need to do dispc_runtime_get() anymore, and the
calls can be removed.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add wait_pending_extra_info_updates() function which can be used to wait
until any extra_info changes have been taken into use by the hardware.
This can be only called when holding the apply mutex, so that other
threads cannot insert new extra_info changes.

This will be used to handle fifo-configurations.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add checks to dss_mgr_enable, dss_mgr_disable, dss_ovl_enable,
dss_ovl_disable that check if the state is already the same as given in
the parameters, and exit if so.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add a helper function dss_apply_ovl_enable(), which is similar to the
main apply() function: dss_apply_ovl_enable() applies the given overlay
enable-status to ovl_priv_data, and sets the dirty flag.

The difference between the helper function and the previous direct use
of the fields is that the helper function will not do anything if the
enable state is already the same as given in the parameter.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

omap_overlay_manager contains device_changed field, which no longer has
any use. So remove the field and the few places where it is touched.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Rename ovl_priv_data's and mgr_priv_data's dirty and shadow_dirty fields
to info_dirty and shadow_info_dirty to better reflect what they mean.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Setting overlay's fifo thresholds is currently handled at the same time
as other overlay attributes. This is not right, as the normal attributes
should only affect one overlay and manager, but changing the fifo
thresholds are needed in cases like fifo-merge, where multiple managers
are affected.

This patch moves the channel field into the "extra_info" set, handled
together with channel and enabled-status.

This also lets us to calculate the fifos only when needed, specifically,
when an overlay or a manager is enabled.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Setting overlay's output channel is currently handled at the same time
as other overlay attributes. This is not right, as the normal attributes
should only affect one overlay and manager, but changing the channel
affects two managers.

This patch moves the channel field into the "extra_info" set, handled
together with enabled-status.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

struct omap_overlayr contains info and info_dirty fields, both of which
should be internal to apply.c.

This patch moves those fields into ovl_priv data, and names them
user_info and user_info_dirty.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

struct omap_overlay_manager contains info and info_dirty fields, both of
which should be internal to apply.c.

This patch moves those fields into mgr_priv data, and names them
user_info and user_info_dirty.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add a helper function mgr_clear_shadow_dirty(), which clears the
shadow_dirty flags for the given manager and for the overlays on that
manager.

This lets us simplify the code in the dss_apply_irq_handler().
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add "updating" flag to mgr_priv_data, which is used to track whether the
manager is currently actively working, i.e. updating the screen.

For auto-update displays updating is always true when the display is
enabled, but for manual update displays the flag is true only during
frame transfers.

The flag is used to manage registers properly, for example when updating
is false and a register for a manager is written, there's no need to set
shadow_dirty flag nor set the GO bit, as the settings will be taken into
use by the HW automatically when the output is enabled.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add dispc_mgr_get_framedone_irq() which returns the irq number for
FRAMEDONE for the given channel.

Note that the function returns always 0 for DIGIT channel, even if OMAP4
does have FRAMEDONE_TV interrupt. The reason for this is that this
function is currently used only to track manual updates, and thus
FRAMEDONE_TV is not needed.

If there's need in the future to also get the FRAMEDONE_TV this needs
revisiting. However, as FRAMEDONE_TV doesn't exist on OMAP2/3, the use
of this function for that purpose needs some extra code to handle the
OMAP2/3 case.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The functions writing to the DISPC registers in apply.c are more complex
than needed. This patch cleans things up.

Two helper functions are added: need_isr(), which returns if an isr for
VSYNC is needed, and need_go(), which tells if there has been a write to
the shadow registers and we need to set the GO bit.

The functions that call the actual dispc write functions will set the
dirty and shadow_dirty flags themselves, instead of that being done on
the caller side. The writing functions also check if the dirty flag is
even set, and return immediately if not.

This allows us to clean up dss_write_regs().
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Overlays are currently enabled and disabled with a boolean in the struct
omap_overlay_info. The overlay info is set with ovl->set_overlay_info(),
and made into use with mgr->apply().

This doesn't work properly, as the enable/disable status may affect also
other overlays, for example when using fifo-merge. Thus the enabling and
disabling of the overlay needs to be done outside the normal overlay
configuration.

This patch achieves that by doing the following things:

1) Add function pointers to struct omap_overlay: enable(), disable() and
is_enabled(). These are used to do the obvious. The functions may block.

2) Move the "enabled" field from struct omap_overlay to ovl_priv_data.

3) Add a new route for settings to be applied to the HW, called
"extra_info". The status of the normal info and extra_info are tracked
separately.

The point here is to allow the normal info to be changed and
applied in non-blocking matter, whereas the extra_info can only be
changed when holding the mutex. This makes it possible to, for example,
set the overlay enable flag, apply it, and wait until the HW has taken
the flag into use.

This is not possible if the enable flag would be in the normal info, as
a new value for the flag could be set at any time from the users of
omapdss.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add a new field to mgr_priv data, "busy", which is used to track the
status of GO bit with the manager. As manual update displays never use
the GO bit, the field is always false for managers used for manual
update displays.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

struct omap_overlay_manager contains "enabled"-field, used to track if
the manager is enabled or not. This field should be internal to apply.c.

This patch moves the field to mgr_priv_data, and applies the necessary
locking when accessing the field.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The current code uses dsi_video_mode_enable/disable functions to
enable/disable DISPC output for video mode displays. For command mode
displays we have no notion in the DISPC side of whether the panel is
enabled, except when a dss_mgr_start_update() call is made.

However, to properly maintain the DISPC state in apply.c, we need to
know if a manager used for a manual update display is currently in use.

This patch achieves that by changing dsi_video_mode_enable/disable to
dsi_enable/disable_video_output, which is called by both video and
command mode displays. For video mode displays it starts the actual
pixel stream, as it did before. For command mode displays it doesn't do
anything else than mark that the manager is currently in use.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The functions in apply.c, called mostly via function pointers in overlay
and overlay_manager structs, will be divided into two groups. The other
group will not sleep and can be called from interrupts, and the other
group may sleep.

The idea is that the non-sleeping functions may only change certain
settings in overlays and managers, and those settings may only affect
the particular overlay/manager. For example, set the base address of the
overlay.

The blocking functions, however, will handle more complex configuration
changes. For example, when an overlay is enabled and fifo-merge feature
is used, we need to do the enable in multiple steps, waiting in between,
and the change affects multiple overlays and managers.

apply.c already contains a spinlock, which has been used to protect
(badly) the dss_data. This patch adds locks/unlocks of the spinlock to
the missing places, and the lock should now properly protect dss_data.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The functions in apply.c, called mostly via function pointers in overlay
and overlay_manager structs, will be divided into two groups. The first
group will not sleep and can be called from interrupts, and the second
group may sleep.

The idea is that the non-sleeping functions may only change certain
settings in overlays and managers, and those settings may only affect
the particular overlay/manager. For example, set the base address of the
overlay.

The blocking functions, however, will handle more complex configuration
changes. For example, when an overlay is enabled and fifo-merge feature
is used, we need to do the enable in multiple steps, waiting in between,
and the change affects multiple overlays and managers.

This patch adds the mutex which is used in the blocking functions to
have exclusive access to overlays and overlay managers.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DSS currently tries to check that the given overlay and overlay manager
settings are acceptable, but the code does not work quite properly.
Things may change between the check and the actual use of the settings.

Furthermore, the following patches will rewrite how settings are
configured and managed, and trying to keep the (broken) settings
checking working during the rewrite would be very difficult.

This patch removes the checking code, and a working version of checking
will be added back after the settings rewrite has been done.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

apply.c will handle the management of dispc in the future patches. This
patch moves overlay manager related functions to apply.c so that they
will have access to the private data and functions of apply.c.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

apply.c will handle the management of dispc in the future patches. This
patch moves overlay related functions to apply.c so that they will have
access to the private data and functions of apply.c.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

dss_cache struct contains private data used to manage dispc. "cache" is
not a good word for it, so rename it to dss_data.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

dss_cache struct contains a spinlock used to protect the struct. A more
logical place for the spinlock is outside the struct that it is
protecting. So move it there.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

manager_cache_data is not a suitable name for the struct. It is more of
a private data for the manager.

Rename the struct to mgr_priv_data, and add a function,
get_mgr_priv(mgr), to get a pointer to the data.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

overlay_cache_data is not a suitable name for the struct. It is more of
a private data for the overlay.

Rename the struct to ovl_priv_data, and add a function,
get_ovl_priv(ovl), to get a pointer to the data.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Make configure_overlay() and configure_manager() take overlay/manager
pointer as an argument, instead of the ovl/mgr id. This will be useful
with the future patches.

Also rename the functions to be a bit more informative:
dss_ovl_write_regs, dss_mgr_write_regs, dss_write_regs.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Use dispc_mgr_get_vsync_irq() to get the interrupt numbers for vsync,
instead of hardcoding the values depending on the display type.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>