Fix checkpatch warnings about use of spaces with operators:

spaces preferred around that '*' (ctx:VxV)

This has been recently added to checkpatch.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

MSI-X is never well-tested, might contain bugs and generally isn't
really all that useful to maintain. Also ath10k is mainly used with
shared/singly-MSI interrupt systems. Hence removing MSI range support.
This change will be useful for further cleanup in copy engine lock
and to add NAPI support.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

10.4 firmware has addeded set_tsf vdev parameter,
hence enable it.
set_tsf function can be used to shift TBTT that will
help avoid its clockdrift which happens when beacons
are collided.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Update 10.4 WMI vdev param to sync to current 10.4 firmware
as of 2/23/2016.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

10.2.4.70.24 firmware introduces new feature to set TSF
via vdev parameter, hence implement relevant function.
set_tsf function can be used to shift TBTT that will
help avoid its clockdrift which happens when beacons
are collided.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This will help anyone trying to use the ack-rssi reporting
feature with the host-specified TX-rate option in 10.4 firmware.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Decrement num_mpdus_ready only when rx amsdu is processed successfully.
Not doing so, will result in leak and impact stabilty under low memory
cases. Also commit 3128b3d8 ("ath10k: speedup htt rx descriptor
processing for rx_ind") missed to removed unused skb list rx_q.

Fixes: 3128b3d8 ("ath10k: speedup htt rx descriptor processing for rx_ind")
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

qca99x0 and qca4019 solutions limit probe responses transmissions.
Logging warning message for each probe response drop is flooding
kernel log unnecessary with " failed to increase tx mgmt pending
count: -16, dropping". Hence reducing log level to debug.
Reported-by: NSebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

pre-calibration is meant for qca4019 which contains only caldata
whereas calibration file is used by ar9888 and qca99x0 that contains
both board data and caldata. So by definition both pre-cal-file and
cal-file can not coexist. Keeping them in shared memory (union), is
breaking boot sequence of qca99x0. Fix it by storing both binaries
in separate memories. This issue is reported in ipq8064 platform which
includes caldata in flash memory.

Fixes: 3d9195ea ("ath10k: incorporate qca4019 cal data download sequence")
Reported-by: NSebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When HW crypto is used, there's no need for the CCMP/GCMP MIC to
be available to mac80211, and the hardware might have removed it
already after checking. The MIC is also useless to have when the
frame is already decrypted, so allow indicating that it's not
present.

Since we are running out of bits in mac80211_rx_flags, make
the flags field a u64.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Check and parse Rx MAC timestamp when firmware sets its flag
to status variable.
10.4 firmware adds it in Rx beacon frame only at this moment.
Drivers and mac80211 may utilize it to detect such clockdrift
or beacon collision and use the result for beacon collision
avoidance.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Since tx completion and rx indication processing are moved out
of txrx tasklet and rx ring lock contention also removed from txrx
for rx_ind messages, it would be efficient to combine both replenish
and txrx tasks. Refill threshold is adjusted for both AP135 and AP148
(low and high end systems). With this adjustment in AP135, TCP DL is
improved from 603 Mbps to 620 Mbps and UDP DL is improved from 758 Mbps
to 803 Mbps. Also no watchdog are observed on UDP BiDi.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Whenever htt rx indication i.e target to host messages are received
on rx copy engine (CE5), the message will be freed after processing
the response. Then CE 5 will be refilled with new descriptors at
post rx processing. This memory alloc and free operations can be avoided
by reusing the same descriptors.

During CE pipe allocation, full ring is not initialized i.e n-1 entries
are filled up. So for CE 5 full ring should be filled up to reuse
descriptors. Moreover CE 5 write index will be updated in single shot
instead of incremental access. This could avoid multiple pci_write and
ce_ring access. From experiments, It improves CPU usage by ~3% in IPQ4019
platform.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The physical address necessary to unmap DMA ('bufferp') is stored
in ath10k_skb_cb as 'paddr'. For diag register read and write
operations, 'paddr' is stored in transfer context. ath10k doesn't rely
on the meta/transfer_id. So the unused output arguments {bufferp, nbytesp
and transfer_idp} are removed from CE recv_next completion.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Except qca61x4 family chips (qca6164, qca6174), copy engine 5 is used
for receiving target to host htt messages. In follow up patch, CE5
descriptors will be reused. In such case, same API can not be used as
htc layer callback where the response messages will be freed at the end.
Hence register new API for HTC layer that free up received message and
keep the message handler common for both HTC and HIF layers.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In follow up patch, htt rx descriptors will be reused instead of
dealloc and refill. To achieve that htt rx indication messages
should not be deferred and should be processed in pci tasklet itself.
Also from rx indication message, mpdu_count alone is used. So it is
maintained as atomic variable and all rx amsdu handlers are done
processed from txrx tasklet. This change get rid of rx_compl_q usage.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Make amsdu handlers (i.e amsdu_pop and rx_h_handler) common to both
rx_ind and frag_ind htt events. It is sufficient to hold rx_ring lock
for amsdu_pop alone and no need to hold it until the packets are
delivered to mac80211. This helps to reduce rx_lock contention as well.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The fw descriptor was never used and probably never will be. It makes
little sense to maintain support for it. Remove it and simplify rx
processing. This will make it easier to optimize rx processing later
as well.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

To optmize CPU usage htt rx descriptors will be reused instead of
refilling it for htt rx copy engine (CE5). To support that all htt rx
indications should be proecssed at same context. Instead of queueing
actual indication message, queue copied message for txrx processing.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

To optimize CPU usage htt rx descriptors will be reused instead of
refilling it for htt rx copy engine (CE5). To support that all htt rx
indications should be processed at same context. FIFO queue is used
to maintain tx completion status for each msdu. This helps to retain
the order of tx completion.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Rx duration support for per station is part of extended peer
stats, enable provision to parse the same and provide backward
compatibility based on the 'stats_id' event
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add API support for Extended Resource Configuration for 10.4. This
is useful to enable new features like Peer Stats, LTEU etc if the
firmware advertises support for the service. This is also done to
provide backward compatibility with older firmware. Also for clarity
send default host platform type as 'WMI_HOST_PLATFORM_HIGH_PERF',
though this should not make any difference in functionality
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Provide a debugfs entry to enable/ disable Peer Stats feature.
Peer Stats feature is for developers/users who are more interested
in studying in Rx/Tx stats with multiple clients connected, hence
disable this by default. Enabling this feature by default results
in unneccessary processing of Peer Stats event for every 500ms
and updating peer_stats list (allocating memory) and cleaning it up
ifexceeds the higher limit and this can be an unnecessary overhead
during long run stress testing.
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

qca4019 calibration data is stored in the host memory and it's mandatory
to download it even before reading board id and chip id from the target.
Also, there is a need to execute otp (download and run) twice, one after
cal data download and another one after board data download.

Existing cal data file name 'cal-<bus>-<id>.bin' and device tree entry
'qcom,ath10k-calibration-data' used in ath10k has assumption that it
carries other data (like board data) also along with the calibration data.
But, qca4019 cal data contains pure calibration data (doesn't include
any other info). So, using existing same cal file name and DT entry
in qca4019 case would alter the purpose of it. To avoid this, new cal
file name 'pre-cal-<bus>-<id>.bin' and new device tree entry name
'qcom,ath10k-pre-calibration-data are introduced.

Overall qca4019's firmware download sequence would look like,

   1) Download cal data (either from a file or device tree entry)
      at the address specified by target in the host interest area
      member "hi_board_data".

   2) Download otp and run with 0x10 (PARAM_GET_EEPROM_BOARD_ID)
      as a argument.

      At this point, otp will take back up of downloaded cal data
      content in another location in the target and return valid
      board id and chip id to the host.

   3) Download board data at the address specified by target
      in host interest area member "hi_board_data".

   4) Download otp and run with 0x10000 (PARAM_FLASH_SECTION_ALL) as
      a argument.

      Now otp will apply cal data content from it's backup on top
      of board data download in step 3 and prepare final data base.

   5) Download code swap and athwlan binary content.

Above sequences are implemented (step 1 to step 4) in the name of
pre calibration configuration.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath10k_download_cal_dt() compares obtained cal data content length
against QCA988X_CAL_DATA_LEN (2116 bytes). It was written by keeping
qca988x in mind. In fact, cal data length is more chip specific.
To make ath10k_download_cal_dt() more generic and reusable for other
chipsets (like qca4019), cal data length is moved to hw_params.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Both ath10k_download_cal_file() and ath10k_download_cal_dt() uses
hard coded file pointer (ar->cal_file) and device tree entry
(qcom,ath10k-calibration-data) respectively to get calibration
data content.

There is a need to use those two functions in qca4019 calibration
download sequence with different file pointer and device tree entry name.
Modify those two functions to take cal data location as an argument.
So that it can serve the purpose for other file pointer and device
tree entry.

This is just preparation before adding actual qca4019 calibration
download sequence. No functional changes.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If device failed to init during early probing
(which is quite rare) it triggered driver to
compute crc before ar->firmware was ready causing
an oops.

Fixes: 3e58044b ("ath10k: print crc32 checksums for firmware and board files")
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This prevents tx hangs or hiccups if pull-push
supporting firmware defines per-txq thresholds or
switches modes dynamically.

Fixes: 29946878 ("ath10k: implement wake_tx_queue")
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The wake_tx_queue/push_pending logic had a bug
which could stop queues indefinitely effectivelly
breaking traffic.

Fixes: 29946878 ("ath10k: implement wake_tx_queue")
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Results obtained from scan can be used for spectrum management by
doing something like building information of preferred channel
lists and sharing them with stations around. It is to be noted
that traffic to the connected stations would be affected during
the scan.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It is observed that, we are disabling the packet log if we write same
value to the pktlog_filter for the second time. Always enable pktlogs
on non zero filter.

Fixes: 90174455 ("ath10k: add support to configure pktlog filter")
Cc: stable@vger.kernel.org
Signed-off-by: NAnilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath10k_core_probe_fw() simply returns error without freeing
cached firmware file content when get board id operation fails.
Free cached fw bin data in failure case to avoid memory leak.

Fixes: db0984e5 ("ath10k: select board data based on BMI chip id and board id")
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Frames that are transmitted via MGMT_TX are using reserved descriptor
slots in firmware. This limitation is for the htt_mgmt_tx path itself,
not for mgmt frames per se. In 16 MBSSID scenario, these reserved slots
will be easy exhausted due to frequent probe responses. So for 10.4
based solutions, probe responses are limited by a threshold (24).

management tx path is separate for all except tlv based solutions. Since
tlv solutions (qca6174 & qca9377) do not support 16 AP interfaces, it is
safe to move management descriptor limitation check under mgmt_tx
function. Though CPU improvement is negligible, unlikely conditions or
never hit conditions in hot path can be avoided on data transmission.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Whenever firmware is configuring operating channel during scan or
home channel, channel change event will be indicated to host. In some
cases (device probe/ last vdev down), target will be configured to
default channel whereas host is unaware of target's operating channel.
This leads to packet drop due to unknown channel and kernel log will be
filled up with "no channel configured; ignoring frame(s)!". Fix that
by handling HTT_T2H_MSG_TYPE_CHAN_CHANGE event.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Check and set Rx MAC timestamp when firmware indicates it.
Firmware adds it in Rx beacon frame only at this moment.
Driver and mac80211 may utilize it to detect such clockdrift
or beacon collision and use the result for beacon collision
avoidance.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Until now only WMI originating mgmt frames were
reported to mac80211. Management frames on HTT
were basically dropped (except frames which looked
like management but had FCS error).

To allow sniffing all frames (including offloaded
frames) without interfering with mac80211
operation and states a new rx_flag was introduced
and is not being used to distinguish frames and
classify them for mac80211.
Signed-off-by: NGrzegorz Bajorski <grzegorz.bajorski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

commit 166de3f1 ("ath10k: remove supported chain mask") had revealed
an issue on monitor mode. Configuring NSS upon monitor interface
creation is causing target assert in all qca9888x and qca6174 firmware.
Firmware assert issue can be reproduced by below sequence even after
reverting commit 166de3f1 ("ath10k: remove supported chain mask").

ip link set wlan0 down
iw wlan0 set type monitor
iw phy0 set antenna 7
ip link set wlan0 up

This issue is originally reported on qca9888 with 10.1 firmware.

Fixes: 5572a95b ("ath10k: apply chainmask settings to vdev on creation")
Cc: stable@vger.kernel.org
Reported-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The number of HTT Tx descriptors and qcache peer
limit aren't hw-specific. In fact they are
firmware specific and should not be placed in
hw_params.

The QCA4019 limits were submitted with the peer
flow control firmware only and to my understanding
there's no non-peer-flow-ctrl QCA4019 firmware.

However QCA99X0 is planned to run firmware
supporting the feature as well. Therefore this
patch enables QCA99X0 to use 2500 tx descriptors
whenever possible instead of just 1424.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

QCA4019 can queue up to 2500 frames at a time.
This means it requires roughly 5000 entires on the
ring to work properly. Otherwise random tx failure
may occur.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The current/old tx path design was that host, at
its own leisure, pushed tx frames to the device.
For HTT there was ~1000-1400 msdu queue depth.

After reaching that limit the driver would request
mac80211 to stop queues. There was little control
over what packets got in there as far as
DA/RA was considered so it was rather easy to
starve per-station traffic flows.

With MU-MIMO this became a significant problem
because the queue depth was insufficient to buffer
frames from multiple clients (which could have
different signal quality and capabilities) in an
efficient fashion.

Hence the new tx path in 10.4 was introduced: a
pull-push mode.

Firmware and host can share tx queue state via
DMA. The state is logically a 2 dimensional array
addressed via peer_id+tid pair. Each entry is a
counter (either number of bytes or packets. Host
keeps it updated and firmware uses it for
scheduling Tx pull requests to host.

This allows MU-MIMO to become a lot more effective
with 10+ clients.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>