The driver queries the FW for WOL support.
Ethtool get/set_wol is implemented accordingly.
Only magic packets are supported at the time.
Signed-off-by: NIgor Yarovinsky <igory@mellanox.co.il>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding capability for RSS for UDP traffic, hashing is done based on
IP addresses and UDP port number.
The support depends on HW/FW capabilities.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The report now based on query from FW, giving the correct tranciever type
and link speed.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The selftest includes 5 features:
1. Interrupt test: Executing commands and receiving command completion
   on all our interrupt vectors.
2. Link test: Verifying we are connected to valid link partner.
3. Speed test: Check that we negotiated link speed correctly.
4. Registers test: Activate HW health check command.
5. Loopback test: Send a packet on loopback interface and catch it on RX side.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Multi-protocol adapters support different port types.  Each consumer
of mlx4_core queries for supported port types; in particular mlx4_ib
can no longer assume that all physical ports belong to it.  Port type
is configured through a sysfs interface.  When the type of a port is
changed, all mlx4 interfaces are unregistered, and then registered
again with the new port types.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Get maximum ethernet MTU and default MAC address from the firmware
QUERY_DEV_CAP command.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

For ethernet support, we need to reserve QPs for the ethernet and
fibre channel driver.  The QPs are reserved at the end of the QP
table.  (This way we assure that they are aligned to their size)

We need to consider these reserved ranges in bitmap creation, so we
extend the mlx4 bitmap utility functions to allow reserved ranges at
both the bottom and the top of the range.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Update existing Mellanox copyright lines to 2008, and add such lines
to files where they are missing.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add support for the following operations to mlx4 when device firmware
supports them:

 - Send with invalidate and local invalidate send queue work requests;
 - Allocate/free fast register MRs;
 - Allocate/free fast register MR page lists;
 - Fast register MR send queue work requests;
 - Local DMA L_Key.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

There was a bug in some versions of the mlx4 driver in
mlx4_alloc_fmr(), which hardcoded the minimum acceptable page_shift to
be 12.  However, new ConnectX firmware can support a minimum
page_shift of 9 (log_pg_sz of 9 returned by QUERY_DEV_LIM) -- so with
old drivers, ib_fmr_alloc() would fail for ULPs using the device
minimum when creating FMRs.

To preserve firmware compatibility with released mlx4 drivers, the
firmware will continue to return 12 as before for log_page_sz in
QUERY_DEV_CAP for these drivers.  However, to enable new drivers to
take advantage of the available smaller page size, the mlx4 driver now
first sets the log_pg_sz to the device minimum by setting a
log_page_sz value to 0 via the MOD_STAT_CFG command and then reading
the real minimum via QUERY_DEV_CAP.
Signed-off-by: NJack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: NVladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add TSO support to the mlx4_ib driver.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The firmware QUERY_ADAPTER command does not return vendor_id,
device_id, and revision_id; eliminate these fields from the query.

Initialize the rev_id field of the mlx4 device via init_node_data (MAD
IFC query), as is done in the query_device verb implementation.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Get the maximum message size from the device capabilities returned
from the QUERY_DEV_CAP firmware command, rather than hard-coding 2 GB.
Signed-off-by: NDotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: NMichael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Upcoming firmware introduces command interface revision 3, which
changes the way port capabilities are queried and set.  Update the
driver to handle both the new and old command interfaces by adding a
new MLX4_FLAG_OLD_PORT_CMDS that it is set after querying the firmware
interface revision and then using the correct interface based on the
setting of the flag.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add an InfiniBand driver for Mellanox ConnectX adapters.  Because
these adapters can also be used as ethernet NICs and Fibre Channel 
HBAs, the driver is split into two modules: 
 
  mlx4_core: Handles low-level things like device initialization and 
    processing firmware commands.  Also controls resource allocation 
    so that the InfiniBand, ethernet and FC functions can share a 
    device without stepping on each other. 
 
  mlx4_ib: Handles InfiniBand-specific things; plugs into the 
    InfiniBand midlayer. 
Signed-off-by: NRoland Dreier <rolandd@cisco.com>