Add a convenience macro for iterating DP encoders.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705164357.28512-2-ville.syrjala@linux.intel.comReviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

PSR is no longer supported on VLV/CHV so this is just dead code.

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180711220050.21809-1-rodrigo.vivi@intel.com

eDP spec states that sink device will do a short pulse in HPD
line when there is a PSR/PSR2 error that needs to be handled by
source, this is handling the first and most simples error:
DP_PSR_SINK_INTERNAL_ERROR.

Here taking the safest approach and disabling PSR(at least until
the next modeset), to avoid multiple rendering issues due to
bad pannels.

v5:
added lockdep_assert in psr_disable and renamed psr_disable()
to intel_psr_disable_locked()

v4:
Using CAN_PSR instead of HAS_PSR in intel_psr_short_pulse

v3:
disabling PSR instead of exiting on error
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626201644.21932-2-jose.souza@intel.com

This became dead code with commit 309bd8ed ("drm/i915: Reinstate
GMBUS and AUX interrupts on gen4/g4x").

v2: Move comment about HW behavior to where decision is made to enable
MSI (Ville).

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180523180435.18042-1-lucas.demarchi@intel.com

We have IS_G45 these days. Let's use it instead of the
'IS_G4X && !IS_GM45' construct.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614180500.2565-1-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

DP spec 1.4 supports training pattern set 4 (TPS4) for HBR3 link
rate. This will be used in link training's channel equalization
phase if supported by both source and sink.
This patch adds the helpers to check if HBR3 is supported and uses
TPS4 in training pattern selection during link training.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: NJames Ausmus <james.ausmus@intel.com>
Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611222655.5696-2-paulo.r.zanoni@intel.com

For ICL, on Combo PHY the allowed max rates are:
 - HBR3 8.1 eDP (DDIA)
 - HBR2 5.4 DisplayPort (DDIB)
and for MG PHY/TC DDI Ports allowed DP rates are:
 - HBR3 8.1 DisplayPort (DP alternate mode, DP over TBT,
 - DP on legacy connector - DDIC/D/E/F)

v2 (from Paulo): Remove misleading comment (Ville).

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: NJames Ausmus <james.ausmus@intel.com>
Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NJames Ausmus <james.ausmus@intel.com>
[Paulo: bikeshed to keep future platforms on "else", v2.]
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611222655.5696-1-paulo.r.zanoni@intel.com

While Bspec doesn't list a specific sequence for turning off the DP port
on g4x we are getting an underrun if the port is disabled in the
.disable() hook. Looks like the pipe stops when the port stops, and by
that time the plane disable may not have completed yet. Also the plane(s)
seem to end up in some wonky state when this happens as they also signal
another underrun immediately after we turn them back on during the next
enable sequence.

We could add a vblank wait in .disable() to avoid wedging the planes,
but I assume we're still tripping up the pipe in some way. So it seems
better to me to just follow the ILK+ sequence and turn off the DP port
in .post_disable() instead. This sequence doesn't seem to suffer from
this problem. Could be it was always the intended sequence for DP and
the gen4 bspec was just never updated to include it.

Originally we used the bad sequence even on ilk+, but I changed that
in commit 08aff3fe ("drm/i915: Move DP port disable to post_disable
for pch platforms") as it was causing issues on those platforms as well.
I left out g4x then only because I didn't have the hardware to test it.
Now that I do it's fairly clear that the ilk+ sequence is also the
right choice for g4x.

v2: Fix whitespace fail (Jani)
    Mention the ilk+ commit (Jani)

Cc: stable@vger.kernel.org
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613160553.11664-2-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Looks like interlaced DP output doesn't work on g4x either. Not all
that surprising considering we already established that interlaced
DP output is busted on VLV/CHV.

Cc: stable@vger.kernel.org
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613160553.11664-1-ville.syrjala@linux.intel.com

When encountering a connector with the scaling mode property both
intel and modesetting ddxs sometimes add tons of DBLSCAN modes
to the output's mode list. The idea presumably being that since the
output will be going through the panel fitter anyway we can pretend
to use any kind of mode.

Sadly that means we can't reject user modes with the DBLSCAN flag
until we know whether we're going to be using the panel's native
mode or the user mode directly. Doing otherwise means X clients using
xf86vidmode/xrandr will get a protocol error (and often self
terminate as a result) when the kernel refuses to use the requested
mode with the DBLSCAN flag.

To undo the regression we'll move the DBLSCAN checks into the
connector->mode_valid() and encoder->compute_config() hooks.

Cc: stable@vger.kernel.org
Cc: Vito Caputo <vcaputo@pengaru.com>
Reported-by: NVito Caputo <vcaputo@pengaru.com>
Fixes: e995ca0b ("drm/i915: Provide a device level .mode_valid() hook")
References: https://lkml.org/lkml/2018/5/21/715Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180524125403.23445-1-ville.syrjala@linux.intel.comReviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106804Tested-by: NArkadiusz Miskiewicz <arekm@maven.pl>

Add support for DP_AUX_E. Here we also introduce the bits for the AUX
power well E, however ICL power well support is still not enabled yet,
so the power well is not used.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NJames Ausmus <james.ausmus@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180612002512.29783-2-paulo.r.zanoni@intel.com

By moving the check from psr_compute_config() to psr_init_dpcd(), we get
to set the dev_priv->psr.sink_support flag only when the panel is
capable of changing power state. An additional benefit is that the check
will be performed only at init time instead of every atomic_check.

This should change the psr_basic IGT failures on HSW to skips.

v2: Return early when SET_POWER_CAPABLE bit is 0 (Jose)

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106217
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106346
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180511195145.3829-2-dhinakaran.pandiyan@intel.com

The power sequencer has bits to allow DP C to be used for eDP.
Currently we assume this will never happen, but I guess it could
theoretically be a thing. Make the code do the right thing in that
case, and toss in a MISSING_CASE() for any other port.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180518152931.13104-5-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Clean up the DP pipe select bits. To make the whole situation a bit
less ugly we'll start to share the same code between .get_hw_state(),
the port state asserts, and the VLV power sequencer code.

v2: Return PIPE_A for cpt/ppt when the port isn't selected by
    any transcoder. Returning INVALID_PIPE explodes *somewhere*
    on some machines (can't immediately see where though). This
    now matches the old behaviour.
v3: Order the defines shift,mask,value (Jani)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180518152931.13104-4-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

This reverts commit dc911f5b.

Per the report, no matter what display mode you select with xrandr, the
i915 driver will always select the alternate fixed mode. For the
reporter this means that the display will always run at 40Hz which is
quite annoying. This may be due to the mode comparison.

But there are some other potential issues. The choice of alt_fixed_mode
seems dubious. It's the first non-preferred mode, but there are no
guarantees that the only difference would be refresh rate. Similarly,
there may be more than one preferred mode in the probed modes list, and
the commit changes the preferred mode selection to choose the last one
on the list instead of the first.

(Note that the probed modes list is the raw, unfiltered, unsorted list
of modes from drm_add_edid_modes(), not the pretty result after a
drm_helper_probe_single_connector_modes() call.)

Finally, we already have eerily similar code in place to find the
downclock mode for DRRS that seems like could be reused here.

Back to the drawing board.

Note: This is a hand-crafted revert due to conflicts. If it fails to
backport, please just try reverting the original commit directly.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105469Reported-by: NRune Petersen <rune@megahurts.dk>
Reported-by: NMark Spencer <n7u4722r35@ynzlx.anonbox.net>
Fixes: dc911f5b ("drm/i915/edp: Allow alternate fixed mode for eDP if available.")
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180516080110.22770-1-jani.nikula@intel.com

i965 does not have native DP. Let's rename the remaining gen4 references
in the DP code to g4x.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180517170309.28630-5-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

To make the intent more clear, let's rename the signal level funcs for
the SNB/IVB CPU eDP.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180517170309.28630-4-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Almost all of the GEN7 checks in the DP code are actually looking for
IVB. HSW doesn't even take these codepaths, and VLV is excluded on
account of not having port A. So let's change the checks to IS_IVB to
make the code less confusing.
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180517170309.28630-3-ville.syrjala@linux.intel.com

All DDI platforms support the full set of preemph settings for each
supported vswing, so let's use the same code for them. We'll also move
the code into intel_ddi.c so that it sits closer to the actual buf trans
tables.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180517170309.28630-2-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Use intel_ddi_dp_voltage_max() for HSW/BDW too instead of letting these
fall through the if ladder in a weird way. This function will look at
the actual buf trans tables we have for HSW/BDW to determine the max
vswing level.

It looks to me like the current code leads HSW port A down the IVB port
A path, HSW port B+ and BDW fall through to the very end. Both cases do
result in the correct max vswing level 2, but it's very hard to see that
from the code.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180517170309.28630-1-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Trivial fix to spelling mistakes in WARN warning message text and
in comments:

"seqeuncer", "seqeuencer" -> "sequencer"
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180509101606.17483-1-colin.king@canonical.com

On intel_dp_compute_config() we were calculating the needed vco
for eDP on gen9 and we stashing it in
intel_atomic_state.cdclk.logical.vco

However few moments later on intel_modeset_checks() we fully
replace entire intel_atomic_state.cdclk.logical with
dev_priv->cdclk.logical fully overwriting the logical desired
vco for eDP on gen9.

So, with wrong VCO value we end up with wrong desired cdclk, but
also it will raise a lot of WARNs: On gen9, when we read
CDCLK_CTL to verify if we configured properly the desired
frequency the CD Frequency Select bits [27:26] == 10b can mean
337.5 or 308.57 MHz depending on the VCO. So if we have wrong
VCO value stashed we will believe the frequency selection didn't
stick and start to raise WARNs of cdclk mismatch.

[   42.857519] [drm:intel_dump_cdclk_state [i915]] Changing CDCLK to 308571 kHz, VCO 8640000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
[   42.897269] cdclk state doesn't match!
[   42.901052] WARNING: CPU: 5 PID: 1116 at drivers/gpu/drm/i915/intel_cdclk.c:2084 intel_set_cdclk+0x5d/0x110 [i915]
[   42.938004] RIP: 0010:intel_set_cdclk+0x5d/0x110 [i915]
[   43.155253] WARNING: CPU: 5 PID: 1116 at drivers/gpu/drm/i915/intel_cdclk.c:2084 intel_set_cdclk+0x5d/0x110 [i915]
[   43.170277] [drm:intel_dump_cdclk_state [i915]] [hw state] 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
[   43.182566] [drm:intel_dump_cdclk_state [i915]] [sw state] 308571 kHz, VCO 8640000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0

v2: Move the entire eDP's vco logical adjustment to inside
    the skl_modeset_calc_cdclk as suggested by Ville.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Fixes: bb0f4aab ("drm/i915: Track full cdclk state for the logical and actual cdclk frequencies")
Cc: <stable@vger.kernel.org> # v4.12+
Link: https://patchwork.freedesktop.org/patch/msgid/20180502175255.5344-1-rodrigo.vivi@intel.com

Abstract compliance test adjustments to a single function. Also make the
bpc adjustments affect the limits, actually forcing the bpc. Seems like
directly changing the pipe_bpp in the past could not have been
effective.
Reviewed-by: NManasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ef61e76003ab7719c82810b742f3fb5765c0e14c.1524730974.git.jani.nikula@intel.com

For now, there's just the one link config selection, optimizing for slow
and wide link. No functional changes.

Keep the debug logging in the caller, to avoid duplication later on if
alternative link confing selection gets added.

v2: Improved commit message
Reviewed-by: NManasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/64848b76bf90d6ceecd7ec6b5add28531e0b1a41.1524730974.git.jani.nikula@intel.com

Also use same min/max model for bpp, and adjust debug logging while at
it.
Reviewed-by: NManasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/72f78c7ae0cd1810798bd94cbf5e574c78da83f8.1524730974.git.jani.nikula@intel.com

Keep related things together. No functional changes.

v2: Fix a typo in patch subject, fix a checkpatch alignment warning.
Reviewed-by: NManasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f24d44547a586a0e342f24e69ab4d576a2474891.1524730974.git.jani.nikula@intel.com

Abstract a new intel_dp_compute_link_config() from
intel_dp_compute_config(), with the parts related to link configuration,
i.e. bpp, link rate, and lane count selection. No functional changes.

v2: Fix a checkpatch warn about spacing.
Reviewed-by: NManasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/80f99a625633f87f44d38d487ba3b32ff9a26b07.1524730974.git.jani.nikula@intel.com

We call intel_dp_compute_rate() in intel_dp_compute_config() only to be
able to debug log the link_bw and rate_select parameters; we don't use
the parameters here for anything else. We call intel_dp_compute_rate()
again during link training where we actually need and use the
parameters.

Move the debug logging of link_bw and rate_select to
intel_dp_link_training_clock_recovery(), and clean up the extra
intel_dp_compute_rate() call and extra clutter from the already
overcrowded intel_dp_compute_config().

v2: Rewrote commit message (Rodrigo, Manasi)
Reviewed-by: NManasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c5cf6a179e2d244eceb6bb80a792765d9efbee4f.1524730974.git.jani.nikula@intel.com

We haven't used the DP bw constants here for a while. No functional
changes.
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NManasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1dc7763cdc70c7f64c0a01f76f218d9ac0717227.1524730974.git.jani.nikula@intel.com

AFAIK CHV was supposed to have HBR2 originally, but in the end the feature
was dropped. We still have some code leftovers from those early days.
Eliminate them.

The extra bit for the training pattern seems to be dead in the hardware.
I can set it (in fact I can set almost any reserved bit in the
registers) but it doesn't seem to interfere with the operation of the
hardware. Either that or I'm very lucky that my displays complete link
training with the incorrect pattern being sent out.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180302095656.19662-1-ville.syrjala@linux.intel.comReviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>

Currently, BXT_PP is hardcoded with value '0'.
It practically disabled eDP backlight on MRB (BXT) platform.

This patch will tell which BXT_PP registers (there are two set of
PP_CONTROL in the spec) to be used as defined in VBT (Video Bios Timing
table) and this will enabled eDP backlight controller on MRB (BXT)
platform.

v2:
 - Remove unnecessary information in commit message.
 - Assign vbt.backlight.controller to a backlight_controller variable and
   return the variable value.
v3:
 - Rebased to latest code base.
 - updated commit title.
Signed-off-by: NMustamin B Mustaffa <mustamin.b.mustaffa@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180227030734.37901-1-mustamin.b.mustaffa@intel.com
(cherry picked from commit 73c0fcac)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Signed-off-by: NLyude Paul <lyude@redhat.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NManasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180308232421.14049-2-lyude@redhat.com

LSPCON likes to throw short HPDs during the enable seqeunce prior to the
link being trained. These obviously result in the channel CR/EQ check
failing and thus we schedule a pointless hotplug work to retrain the
link. Avoid that by ignoring the bad CR/EQ status until we've actually
initially trained the link.

I've not actually investigated to see what LSPCON is trying to signal
with the short pulse. But as long as it signals anything I think we're
supposed to check the link status anyway, so I don't really see other
good ways to solve this. I've not seen these short pulses being
generated by normal DP sinks.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NLyude Paul <lyude@redhat.com>
Signed-off-by: NLyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117192149.17760-5-ville.syrjala@linux.intel.com

Doing link retraining from the short pulse handler is problematic since
that might introduce deadlocks with MST sideband processing. Currently
we don't retrain MST links from this code, but we want to change that.
So better to move the entire thing to the hotplug work. We can utilize
the new encoder->hotplug() hook for this.

The only thing we leave in the short pulse handler is the link status
check. That one still depends on the link parameters stored under
intel_dp, so no locking around that but races should be mostly harmless
as the actual retraining code will recheck the link state if we
end up there by mistake.

v2: Rebase due to ->post_hotplug() now being just ->hotplug()
    Check the connector type to figure out if we should do
    the HDMI thing or the DP think for DDI

[pushed with whitespace changes for sparse]
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: NManasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NLyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117192149.17760-3-ville.syrjala@linux.intel.com

The LG 4k TV I have doesn't deassert HPD when I turn the TV off, but
when I turn it back on it will pulse the HPD line. By that time it has
forgotten everything we told it about scrambling and the clock ratio.
Hence if we want to get a picture out if it again we have to tell it
whether we're currently sending scrambled data or not. Implement
that via the encoder->hotplug() hook.

v2: Force a full modeset to not follow the HDMI 2.0 spec more
    closely (Shashank)

[pushed with whitespace fixes to make sparse happy]
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NLyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117192149.17760-1-ville.syrjala@linux.intel.com

We have two instances of the code to fill out the header for the aux
message. Pull it into a small helper.

v2: Rebase due to txbuf[] changes

Cc: Sean Paul <seanpaul@chromium.org>
Cc: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222212802.4826-1-ville.syrjala@linux.intel.comReviewed-by: NRamalingam C <ramalingam.c@intel.com>

Let's try to keep the details on the AKSV stuff concentrated
in one place. So move the control bit and +5 data size handling
there.

v2: Increase txbuf[] to include the payload which intel_dp_aux_xfer()
    will still load into the registers even though the hardware
    will ignore it

Cc: Sean Paul <seanpaul@chromium.org>
Cc: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222212732.4665-1-ville.syrjala@linux.intel.comReviewed-by: NRamalingam C <ramalingam.c@intel.com>

Rename intel_dp_aux_ch() to intel_dp_aux_xfer() to better convey
what it actually does.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222181036.15251-6-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> #irc

dp_rates[] array is a superset of all the link rates supported
by sink devices. DP 1.3 specification adds HBR3 (8.1Gbps) link rate
to the set of link rates supported by sink. This patch adds this rate
to dp_rates[] array that gets used to populate the sink_rates[]
array limited by max rate obtained from DP_MAX_LINK_RATE DPCD register.

v2:
* Rebased on top of Jani's localized rates patch

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1519857110-26916-1-git-send-email-manasi.d.navare@intel.com

Localize link rate arrays by moving them to the functions where they're
used. Further clarify the distinction between source and sink
capabilities. Split pre and post Haswell arrays, and get rid of the
array size arithmetics. Use a direct rate value in the paranoia case of
no common rates find.

Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180227105911.4485-1-jani.nikula@intel.com