AMD hardware adds two additional bits to aid in nested page fault handling.

Bit 32 - NPF occurred while translating the guest's final physical address
Bit 33 - NPF occurred while translating the guest page tables

The guest page tables fault indicator can be used as an aid for nested
virtualization. Using V0 for the host, V1 for the first level guest and
V2 for the second level guest, when both V1 and V2 are using nested paging
there are currently a number of unnecessary instruction emulations. When
V2 is launched shadow paging is used in V1 for the nested tables of V2. As
a result, KVM marks these pages as RO in the host nested page tables. When
V2 exits and we resume V1, these pages are still marked RO.

Every nested walk for a guest page table is treated as a user-level write
access and this causes a lot of NPFs because the V1 page tables are marked
RO in the V0 nested tables. While executing V1, when these NPFs occur KVM
sees a write to a read-only page, emulates the V1 instruction and unprotects
the page (marking it RW). This patch looks for cases where we get a NPF due
to a guest page table walk where the page was marked RO. It immediately
unprotects the page and resumes the guest, leading to far fewer instruction
emulations when nested virtualization is used.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: NBorislav Petkov <bp@suse.de>
Signed-off-by: NBrijesh Singh <brijesh.singh@amd.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

Change unimplemented msrs messages to use pr_debug.
If CONFIG_DYNAMIC_DEBUG is set, then these messages can be
enabled at run time or else -DDEBUG can be used at compile
time to enable them. These messages will still be printed if
ignore_msrs=1.
Signed-off-by: NBandan Das <bsd@redhat.com>
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

 - Expose all invalidation types to the L1

 - Reject invvpid instruction, if L1 passed zero vpid value to single
   context invalidations
Signed-off-by: NJan Dakinevich <jan.dakinevich@gmail.com>
Tested-by: NLadi Prosek <lprosek@redhat.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

 - Remove VMX_EPT_EXTENT_INDIVIDUAL_ADDR, since there is no such type of
   EPT invalidation

 - Add missing VPID types names
Signed-off-by: NJan Dakinevich <jan.dakinevich@gmail.com>
Tested-by: NLadi Prosek <lprosek@redhat.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

From the Intel SDM, volume 3, section 10.4.3, "Enabling or Disabling the
Local APIC,"

  When IA32_APIC_BASE[11] is 0, the processor is functionally equivalent
  to an IA-32 processor without an on-chip APIC. The CPUID feature flag
  for the APIC (see Section 10.4.2, "Presence of the Local APIC") is
  also set to 0.
Signed-off-by: NJim Mattson <jmattson@google.com>
[Changed subject tag from nVMX to x86.]
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

Add two new AVX512 subfeatures support for KVM guest.

AVX512_4VNNIW:
Vector instructions for deep learning enhanced word variable precision.

AVX512_4FMAPS:
Vector instructions for deep learning floating-point single precision.
Reviewed-by: NBorislav Petkov <bp@suse.de>
Signed-off-by: NHe Chen <he.chen@linux.intel.com>
Signed-off-by: NLuwei Kang <luwei.kang@intel.com>
[Changed subject tags.]
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

Internal errors were reported on 16 bit fxsave and fxrstor with ipxe.
Old Intels don't have unrestricted_guest, so we have to emulate them.

The patch takes advantage of the hardware implementation.

AMD and Intel differ in saving and restoring other fields in first 32
bytes.  A test wrote 0xff to the fxsave area, 0 to upper bits of MCSXR
in the fxsave area, executed fxrstor, rewrote the fxsave area to 0xee,
and executed fxsave:

  Intel (Nehalem):
    7f 1f 7f 7f ff 00 ff 07 ff ff ff ff ff ff 00 00
    ff ff ff ff ff ff 00 00 ff ff 00 00 ff ff 00 00
  Intel (Haswell -- deprecated FPU CS and FPU DS):
    7f 1f 7f 7f ff 00 ff 07 ff ff ff ff 00 00 00 00
    ff ff ff ff 00 00 00 00 ff ff 00 00 ff ff 00 00
  AMD (Opteron 2300-series):
    7f 1f 7f 7f ff 00 ee ee ee ee ee ee ee ee ee ee
    ee ee ee ee ee ee ee ee ff ff 00 00 ff ff 02 00

fxsave/fxrstor will only be emulated on early Intels, so KVM can't do
much to improve the situation.
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

Move the existing exception handling for inline assembly into a macro
and switch its return values to X86EMUL type.
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Alignments are exclusive, so 5 modes can be expressed in 3 bits.
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Needed for FXSAVE and FXRSTOR.
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

The local variable *gpa_offset* is set but not used afterwards,
which make the compiler issue a warning with option
-Wunused-but-set-variable. Remove it to avoid the warning.
Signed-off-by: NJiang Biao <jiang.biao2@zte.com.cn>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

synic_set_irq is only used in hyperv.c, and should be static to
avoid compiling warning when with -Wmissing-prototypes option.
Signed-off-by: NJiang Biao <jiang.biao2@zte.com.cn>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

The use of local variable *function* is not necessary here. Remove
it to avoid compiling warning with -Wunused-but-set-variable option.
Signed-off-by: NJiang Biao <jiang.biao2@zte.com.cn>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

kvm_emulate_wbinvd_noskip is only used in x86.c, and should be
static to avoid compiling warning when with -Wmissing-prototypes
option.
Signed-off-by: NJiang Biao <jiang.biao2@zte.com.cn>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

vmx_arm_hv_timer is only used in vmx.c, and should be static to
avoid compiling warning when with -Wmissing-prototypes option.
Signed-off-by: NJiang Biao <jiang.biao2@zte.com.cn>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Merge branch 'x86/cpufeature' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into kvm/next

Topic branch for AVX512_4VNNIW and AVX512_4FMAPS support in KVM.

Sparse populated CPUID leafs are collected in a software provided leaf to
avoid bloat of the x86_capability array, but there is no way to rebuild the
real leafs (e.g. for KVM CPUID enumeration) other than rereading the CPUID
leaf from the CPU. While this is possible it is problematic as it does not
take software disabled features into account. If a feature is disabled on
the host it should not be exposed to a guest either.

Add get_scattered_cpuid_leaf() which rebuilds the leaf from the scattered
cpuid table information and the active CPU features.

[ tglx: Rewrote changelog ]
Signed-off-by: NHe Chen <he.chen@linux.intel.com>
Reviewed-by: NBorislav Petkov <bp@suse.de>
Cc: Luwei Kang <luwei.kang@intel.com>
Cc: kvm@vger.kernel.org
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Piotr Luc <Piotr.Luc@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Link: http://lkml.kernel.org/r/1478856336-9388-3-git-send-email-he.chen@linux.intel.comSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

cpuid_regs is defined multiple times as structure and enum. Rename the enum
and move all of it to processor.h so we don't end up with more instances.

Rename the misnomed register enumeration from CR_* to the obvious CPUID_*.

[ tglx: Rewrote changelog ]
Signed-off-by: NHe Chen <he.chen@linux.intel.com>
Reviewed-by: NBorislav Petkov <bp@alien8.de>
Cc: Luwei Kang <luwei.kang@intel.com>
Cc: kvm@vger.kernel.org
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Piotr Luc <Piotr.Luc@intel.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Link: http://lkml.kernel.org/r/1478856336-9388-2-git-send-email-he.chen@linux.intel.comSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Pull KVM fixes from Paolo Bonzini:
 "ARM fixes.  There are a couple pending x86 patches but they'll have to
  wait for next week"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: arm/arm64: vgic: Kick VCPUs when queueing already pending IRQs
  KVM: arm/arm64: vgic: Prevent access to invalid SPIs
  arm/arm64: KVM: Perform local TLB invalidation when multiplexing vcpus on a single CPU

Merge media fixes from Mauro Carvalho Chehab:
 "This contains two patches fixing problems with my patch series meant
  to make USB drivers to work again after the DMA on stack changes.

  The last patch on this series is actually not related to DMA on stack.
  It solves a longstanding bug affecting module unload, causing
  module_put() to be called twice. It was reported by the user who
  reported and tested the issues with the gp8psk driver with the DMA
  fixup patches. As we're late at -rc cycle, maybe you prefer to not
  apply it right now. If this is the case, I'll add to the pile of
  patches for 4.10.

  Exceptionally this time, I'm sending the patches via e-mail, because
  I'm on another trip, and won't be able to use the usual procedure
  until Monday. Also, it is only three patches, and you followed already
  the discussions about the first one"

* emailed patches from Mauro Carvalho Chehab <mchehab@osg.samsung.com>:
  gp8psk: Fix DVB frontend attach
  gp8psk: fix gp8psk_usb_in_op() logic
  dvb-usb: move data_mutex to struct dvb_usb_device

Pull char/misc fixes from Greg KH:
 "Here are three small driver fixes for some reported issues for
  4.9-rc5.

  One for the hyper-v subsystem, fixing up a naming issue that showed up
  in 4.9-rc1, one mei driver fix, and one fix for parallel ports,
  resolving a reported regression.

  All have been in linux-next with no reported issues"

* tag 'char-misc-4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  ppdev: fix double-free of pp->pdev->name
  vmbus: make sysfs names consistent with PCI
  mei: bus: fix received data size check in NFC fixup

Pull driver core fixes from Greg KH:
 "Here are two driver core fixes for 4.9-rc5.

  The first resolves an issue with some drivers not liking to be unbound
  and bound again (if CONFIG_DEBUG_TEST_DRIVER_REMOVE is enabled), which
  solves some reported problems with graphics and storage drivers. The
  other resolves a smatch error with the 4.9-rc1 driver core changes
  around this feature.

  Both have been in linux-next with no reported issues"

* tag 'driver-core-4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  driver core: fix smatch warning on dev->bus check
  driver core: skip removal test for non-removable drivers

Pull staging/IIO fixes from Grek KH:
 "Here are a few small staging and iio driver fixes for reported issues.

  The last one was cherry-picked from my -next branch to resolve a build
  warning that Arnd fixed, in his quest to be able to turn
  -Wmaybe-uninitialized back on again. That patch, and all of the
  others, have been in linux-next for a while with no reported issues"

* tag 'staging-4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  iio: maxim_thermocouple: detect invalid storage size in read()
  staging: nvec: remove managed resource from PS2 driver
  Revert "staging: nvec: ps2: change serio type to passthrough"
  drivers: staging: nvec: remove bogus reset command for PS/2 interface
  staging: greybus: arche-platform: fix device reference leak
  staging: comedi: ni_tio: fix buggy ni_tio_clock_period_ps() return value
  staging: sm750fb: Fix bugs introduced by early commits
  iio: hid-sensors: Increase the precision of scale to fix wrong reading interpretation.
  iio: orientation: hid-sensor-rotation: Add PM function (fix non working driver)
  iio: st_sensors: fix scale configuration for h3lis331dl
  staging: iio: ad5933: avoid uninitialized variable in error case

Pull USB / PHY fixes from Greg KH:
 "Here are a number of small USB and PHY driver fixes for 4.9-rc5

  Nothing major, just small fixes for reported issues, all of these have
  been in linux-next for a while with no reported issues"

* tag 'usb-4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: cdc-acm: fix TIOCMIWAIT
  cdc-acm: fix uninitialized variable
  drivers/usb: Skip auto handoff for TI and RENESAS usb controllers
  usb: musb: remove duplicated actions
  usb: musb: da8xx: Don't print phy error on -EPROBE_DEFER
  phy: sun4i: check PMU presence when poking unknown bit of pmu
  phy-rockchip-pcie: remove deassert of phy_rst from exit callback
  phy: da8xx-usb: rename the ohci device to ohci-da8xx
  phy: Add reset callback for not generic phy
  uwb: fix device reference leaks
  usb: gadget: u_ether: remove interrupt throttling
  usb: dwc3: st: add missing <linux/pinctrl/consumer.h> include
  usb: dwc3: Fix error handling for core init

Pull more block fixes from Jens Axboe:
 "Since I mistakenly left out the lightnvm regression fix yesterday and
  the aoeblk seems adequately tested at this point, might as well send
  out another pull to make -rc5"

* 'for-linus' of git://git.kernel.dk/linux-block:
  aoe: fix crash in page count manipulation
  lightnvm: invalid offset calculation for lba_shift

Pull SCSI fixes from James Bottomley:
 "The megaraid_sas patch in here fixes a major regression in the last
  fix set that made all megaraid_sas cards unusable. It turns out no-one
  had actually tested such an "obvious" fix, sigh. The fix for the fix
  has been tested ...

  The next most serious is the vmw_pvscsi abort problem which basically
  means that aborts don't work on the vmware paravirt devices and error
  handling always escalates to reset.

  The rest are an assortment of missed reference counting in certain
  paths and corner case bugs that show up on some architectures"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: megaraid_sas: fix macro MEGASAS_IS_LOGICAL to avoid regression
  scsi: qla2xxx: fix invalid DMA access after command aborts in PCI device remove
  scsi: qla2xxx: do not queue commands when unloading
  scsi: libcxgbi: fix incorrect DDP resource cleanup
  scsi: qla2xxx: Fix scsi scan hang triggered if adapter fails during init
  scsi: scsi_dh_alua: Fix a reference counting bug
  scsi: vmw_pvscsi: return SUCCESS for successful command aborts
  scsi: mpt3sas: Fix for block device of raid exists even after deleting raid disk
  scsi: scsi_dh_alua: fix missing kref_put() in alua_rtpg_work()

Pull clk fixes from Stephen Boyd:
 "The typical collection of minor bug fixes in clk drivers. We don't
  have anything in the core framework here, just driver fixes.

  There's a boot fix for Samsung devices and a safety measure for qoriq
  to prevent CPUs from running too fast. There's also a fix for i.MX6Q
  to properly handle audio clock rates. We also have some "that's
  obviously wrong" fixes like bad NULL pointer checks in the MPP driver
  and a poor usage of __pa in the xgene clk driver that are fixed here"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: mmp: pxa910: fix return value check in pxa910_clk_init()
  clk: mmp: pxa168: fix return value check in pxa168_clk_init()
  clk: mmp: mmp2: fix return value check in mmp2_clk_init()
  clk: qoriq: Don't allow CPU clocks higher than starting value
  clk: imx: fix integer overflow in AV PLL round rate
  clk: xgene: Don't call __pa on ioremaped address
  clk/samsung: Use CLK_OF_DECLARE_DRIVER initialization method for CLKOUT
  clk: rockchip: don't return NULL when failing to register ddrclk branch

The DVB binding schema at the DVB core assumes that the frontend is a
separate driver.  Faling to do that causes OOPS when the module is
removed, as it tries to do a symbol_put_addr on an internal symbol,
causing craches like:

    WARNING: CPU: 1 PID: 28102 at kernel/module.c:1108 module_put+0x57/0x70
    Modules linked in: dvb_usb_gp8psk(-) dvb_usb dvb_core nvidia_drm(PO) nvidia_modeset(PO) snd_hda_codec_hdmi snd_hda_intel snd_hda_codec snd_hwdep snd_hda_core snd_pcm snd_timer snd soundcore nvidia(PO) [last unloaded: rc_core]
    CPU: 1 PID: 28102 Comm: rmmod Tainted: P        WC O 4.8.4-build.1 #1
    Hardware name: MSI MS-7309/MS-7309, BIOS V1.12 02/23/2009
    Call Trace:
       dump_stack+0x44/0x64
       __warn+0xfa/0x120
       module_put+0x57/0x70
       module_put+0x57/0x70
       warn_slowpath_null+0x23/0x30
       module_put+0x57/0x70
       gp8psk_fe_set_frontend+0x460/0x460 [dvb_usb_gp8psk]
       symbol_put_addr+0x27/0x50
       dvb_usb_adapter_frontend_exit+0x3a/0x70 [dvb_usb]

From Derek's tests:
    "Attach bug is fixed, tuning works, module unloads without
     crashing. Everything seems ok!"
Reported-by: NDerek <user.vdr@gmail.com>
Tested-by: NDerek <user.vdr@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit bc29131ecb10 ("[media] gp8psk: don't do DMA on stack") fixed the
usage of DMA on stack, but the memcpy was wrong for gp8psk_usb_in_op().
Fix it.

From Derek's email:
    "Fix confirmed using 2 different Skywalker models with
     HD mpeg4, SD mpeg2."
Suggested-by: NJohannes Stezenbach <js@linuxtv.org>
Fixes: bc29131ecb10 ("[media] gp8psk: don't do DMA on stack")
Tested-by: NDerek <user.vdr@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The data_mutex is initialized too late, as it is needed for
each device driver's power control, causing an OOPS:

    dvb-usb: found a 'TerraTec/qanu USB2.0 Highspeed DVB-T Receiver' in warm state.
    BUG: unable to handle kernel NULL pointer dereference at           (null)
    IP: [<ffffffff846617af>] __mutex_lock_slowpath+0x6f/0x100 PGD 0
    Oops: 0002 [#1] SMP
    Modules linked in: dvb_usb_cinergyT2(+) dvb_usb
    CPU: 0 PID: 2029 Comm: modprobe Not tainted 4.9.0-rc4-dvbmod #24
    Hardware name: FUJITSU LIFEBOOK A544/FJNBB35 , BIOS Version 1.17 05/09/2014
    task: ffff88020e943840 task.stack: ffff8801f36ec000
    RIP: 0010:[<ffffffff846617af>]  [<ffffffff846617af>] __mutex_lock_slowpath+0x6f/0x100
    RSP: 0018:ffff8801f36efb10  EFLAGS: 00010282
    RAX: 0000000000000000 RBX: ffff88021509bdc8 RCX: 00000000c0000100
    RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff88021509bdcc
    RBP: ffff8801f36efb58 R08: ffff88021f216320 R09: 0000000000100000
    R10: ffff88021f216320 R11: 00000023fee6c5a1 R12: ffff88020e943840
    R13: ffff88021509bdcc R14: 00000000ffffffff R15: ffff88021509bdd0
    FS:  00007f21adb86740(0000) GS:ffff88021f200000(0000) knlGS:0000000000000000
    CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
    CR2: 0000000000000000 CR3: 0000000215bce000 CR4: 00000000001406f0
    Call Trace:
       mutex_lock+0x16/0x25
       cinergyt2_power_ctrl+0x1f/0x60 [dvb_usb_cinergyT2]
       dvb_usb_device_init+0x21e/0x5d0 [dvb_usb]
       cinergyt2_usb_probe+0x21/0x50 [dvb_usb_cinergyT2]
       usb_probe_interface+0xf3/0x2a0
       driver_probe_device+0x208/0x2b0
       __driver_attach+0x87/0x90
       driver_probe_device+0x2b0/0x2b0
       bus_for_each_dev+0x52/0x80
       bus_add_driver+0x1a3/0x220
       driver_register+0x56/0xd0
       usb_register_driver+0x77/0x130
       do_one_initcall+0x46/0x180
       free_vmap_area_noflush+0x38/0x70
       kmem_cache_alloc+0x84/0xc0
       do_init_module+0x50/0x1be
       load_module+0x1d8b/0x2100
       find_symbol_in_section+0xa0/0xa0
       SyS_finit_module+0x89/0x90
       entry_SYSCALL_64_fastpath+0x13/0x94
    Code: e8 a7 1d 00 00 8b 03 83 f8 01 0f 84 97 00 00 00 48 8b 43 10 4c 8d 7b 08 48 89 63 10 4c 89 3c 24 41 be ff ff ff ff 48 89 44 24 08 <48> 89 20 4c 89 64 24 10 eb 1a 49 c7 44 24 08 02 00 00 00 c6 43 RIP  [<ffffffff846617af>] __mutex_lock_slowpath+0x6f/0x100 RSP <ffff8801f36efb10>
    CR2: 0000000000000000

So, move it to the struct dvb_usb_device and initialize it
before calling the driver's callbacks.
Reported-by: NJörg Otte <jrg.otte@gmail.com>
Tested-by: NJörg Otte <jrg.otte@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

As found by gcc -Wmaybe-uninitialized, having a storage_bytes value other
than 2 or 4 will result in undefined behavior:

drivers/iio/temperature/maxim_thermocouple.c: In function 'maxim_thermocouple_read':
drivers/iio/temperature/maxim_thermocouple.c:141:5: error: 'ret' may be used uninitialized in this function [-Werror=maybe-uninitialized]

This probably cannot happen, but returning -EINVAL here is appropriate
and makes gcc happy and the code more robust.

Fixes: 231147ee ("iio: maxim_thermocouple: Align 16 bit big endian value of raw reads")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>
(cherry picked from commit 32cb7d27)
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

aoeblk contains some mysterious code, that wants to elevate the bio
vec page counts while it's under IO. That is not needed, it's
fragile, and it's causing kernel oopses for some.
Reported-by: NTested-by: Don Koch <kochd@us.ibm.com>
Tested-by: NTested-by: Don Koch <kochd@us.ibm.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

The ns->lba_shift assumes its value to be the logarithmic of the
LA size. A previous patch duplicated the lba_shift calculation into
lightnvm. It prematurely also subtracted a 512byte shift, which commonly
is applied per-command. The 512byte shift being subtracted twice led to
data loss when restoring the logical to physical mapping table from
device and when issuing I/O commands using rrpc.

Fix offset by removing the 512byte shift subtraction when calculating
lba_shift.

Fixes: b0b4e09c "lightnvm: control life of nvm_dev in driver"
Reported-by: NJavier González <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

Pull ACPI fix from Rafael Wysocki:
 "Fix a recent regression in the 8250_dw serial driver introduced by
  adding a quirk for the APM X-Gene SoC to it which uncovered an issue
  related to the handling of built-in device properties in the core ACPI
  device enumeration code (Heikki Krogerus)"

* tag 'acpi-4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / platform: Add support for build-in properties

Pull power management fixes from Rafael Wysocki:
 "These fix two bugs in error code paths in the PM core (system-wide
  suspend of devices), a device reference leak in the boot-time suspend
  test code and a cpupower utility regression from the 4.7 cycle.

  Specifics:

   - Prevent the PM core from attempting to suspend parent devices if
     any of their children, whose suspend callbacks were invoked
     asynchronously, have failed to suspend during the "late" and
     "noirq" phases of system-wide suspend of devices (Brian Norris).

   - Prevent the boot-time system suspend test code from leaking a
     reference to the RTC device used by it (Johan Hovold).

   - Fix cpupower to use the return value of one of its library
     functions correctly and restore the correct behavior of it when
     used for setting cpufreq tunables broken during the 4.7 development
     cycle (Laura Abbott)"

* tag 'pm-4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PM / sleep: don't suspend parent when async child suspend_{noirq, late} fails
  PM / sleep: fix device reference leak in test_suspend
  cpupower: Correct return type of cpu_power_is_cpu_online() in cpufreq-set

Pull ARC fixes from Vineet Gupta:

 - mmap handler for dma ops as generic handler no longer works for us
   [Alexey]

 - Fixes for EZChip platform [Noam]

 - Fix RTC clocksource driver build issue

 - ARC IRQ handling fixes [Yuriy]

 - Revert a recent makefile change which doesn't go well with oldish
   tools out in the wild

* tag 'arc-4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARCv2: MCIP: Use IDU_M_DISTRI_DEST mode if there is only 1 destination core
  ARC: IRQ: Do not use hwirq as virq and vice versa
  ARC: [plat-eznps] set default baud for early console
  ARC: [plat-eznps] remove IPI clear from SMP operations
  Revert "ARC: build: retire old toggles"
  ARC: timer: rtc: implement read loop in "C" vs. inline asm
  ARC: change return value of userspace cmpxchg assist syscall
  arc: Implement arch-specific dma_map_ops.mmap
  ARC: [SMP] avoid overriding present cpumask
  ARC: Enable PERF_EVENTS in nSIM driven platforms

Merge tag 'platform-drivers-x86-v4.9-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86

Pull x86 platform driver fixes from Darren Hart:
 "Minor doc fix, a DMI match for ideapad and a fix to toshiba-wmi to
  avoid loading on non-toshiba systems.

  Documentation/ABI:
   - ibm_rtl: The "What:" fields are incomplete

  toshiba-wmi:
   - Fix loading the driver on non Toshiba laptops

  ideapad-laptop:
   - Add another DMI entry for Yoga 900"

* tag 'platform-drivers-x86-v4.9-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
  Documentation/ABI: ibm_rtl: The "What:" fields are incomplete
  toshiba-wmi: Fix loading the driver on non Toshiba laptops
  ideapad-laptop: Add another DMI entry for Yoga 900

Pull block fixes from Jens Axboe:
 "Two small (really, one liners both of them!) fixes that should go into
  this series:

   - Request allocation error handling fix for nbd, from Christophe,
     fixing a regression in this series.

   - An oops fix for drbd. Not a regression in this series, but stable
     material. From Richard"

* 'for-linus' of git://git.kernel.dk/linux-block:
  drbd: Fix kernel_sendmsg() usage - potential NULL deref
  nbd: Fix error handling

Pull PCI fixes from Bjorn Helgaas:

 - Update MAINTAINERS for Intel VMD driver filename

 - Update Rockchip rk3399 host bridge driver DTS and resets

 - Fix ROM shadow problem that made some video device initialization
   fail

* tag 'pci-v4.9-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: VMD: Update filename to reflect move
  arm64: dts: rockchip: add three new resets for rk3399 PCIe controller
  PCI: rockchip: Add three new resets as required properties
  PCI: Don't attempt to claim shadow copies of ROM