Currently Haleakala uses the Kilauea platform code. This patch adds
"haleakala" to the compatible property, in case later kernel versions
will introduce a Haleakala platform code.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

The patch adds the Glacier dts. The Glacier is nearly identical to the
Canyonlands (460EX). Here the differences:

- 4 ethernet ports instead of 2
- no SATA port
- no USB port
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch adds TAH (TCP/IP Acceleration Hardware) support to the
taishan 440GX dts. It depends on the NEWEMAC/tah patch that adds the
compatible "ibm,tah" property to the matching table.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Use dcri_clrset() for PCIe SDR0 read/modify/write access.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Add the cuboot wrapper for the AMCC 440EP Yosemite board
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

The AMCC 440EP Yosemite board is very similar to the original AMCC Bamboo
board.  This adds a YOSEMITE option to Kconfig, and reuses the existing
bamboo board support in the kernel.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This adds a DTS file for the AMCC 440EP Yosemite board.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

All this code is needed to properly initialize the 460EX PCIe host
bridge(s). We re-initialize all ports again, even though this has been done
in the bootloader (U-Boot) before. This way we make sure, that we always
run the latest init code in Linux and don't depend on code versions from
U-Boot.

Unfortunately all IBM/AMCC chips currently supported in this PCIe driver need
a different reset-/init-sequence.

Tested on AMCC Canyonlands eval board.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This dts source file for the AMCC 460EX Canyonlands evalutaion board
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Canyonlands is the AMCC 460EX eval board, featuring nearly all of the 460EX
interfaces:

- 1 * PCI (max 66MHz), 2 * PCIe (one 4-lane, one 1-lane)
- 2 * GBit Ethernet with TCP/IP acceleration
- USB 2.0 Host/Device OTG and Host interface
- SATA port
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch adds basic support for the AMCC 460EX/460GT PPC's to arch/powerpc.
Currently those PPC's are still based on a 440 core and *not* a 460 core.

Here some basic features of those SoC's:

460EX:
- Up to 1.2GHz, 32kB L1 I-cache and D-cache, 256kB L2-cache, FPU
- 1 * PCI (max 66MHz), 2 * PCIe (one 4-lane, one 1-lane)
- 2 * GBit Ethernet with TCP/IP acceleration
- USB 2.0 Host/Device OTG and Host interface
- SATA controller
- Optional security feature

460GT (only changes to 460EX):
- 4 * GBit Ethernet with TCP/IP acceleration
- RapidIO
- No SATA
- No USB
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch alters the bootwrapper for a number of machines (roubhly
all 4xx based cuboot or treeboot platforms) to use aliases instead of
the linux,network-index hack to work out which MAC address to attach
to which ethernet device node.

The now obsolete linux,network-index properties are removed from the
corresponding device trees.  This won't break backwards compatiblity,
because in cases where this fixup code is relevant, the device tree is
part of the kernel image.

The references to linux,network-index are removed from
booting-without-of.txt.  Not only is it now deprecated, but as a hack
applicable only when the device tree blob and fixup code were in the
same image, this property never belonged in booting-without-of.txt
which describes the interface between the kernel and firmware or
bootloaders which produce a device tree.  By the time the device tree
reaches the kernel, all the MAC addresses must be fully filled in.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

scanlog_init() could use some love.

* properly return -ENODEV if this system doesn't support scan-log-dump
* don't printk if scan-log-dump not present; only older systems have it
* convert from create_proc_entry() to preferred proc_create()
* allocate zeroed data buffer
* fix potential memory leak of ent->data on failed create_proc_entry()
* simplify control flow
Signed-off-by: NNathan Lynch <ntl@pobox.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This adds /sys/kernel/phyp_dump_active so that kdump init scripts may
look for it and take appropriate action if this file is found.  This
file is only created when phyp_dump has been registered.
Signed-off-by: NManish Ahuja <mahuja@us.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This adds a kernel command line option "phyp_dump", which takes a 0/1
value for disabling/ enabling phyp_dump at boot time.  Kdump can use
this on cmdline (phyp_dump=0) to disable phyp-dump during boot when
enabling itself.  This will ensure only one dumping mechanism is active
at any given time.
Signed-off-by: NManish Ahuja <mahuja@us.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add hypervisor-assisted dump to kernel config.
Signed-off-by: NLinas Vepstas <linasvepstas@gmail.com>
Signed-off-by: NManish Ahuja <mahuja@us.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This tracks the size freed.  For now it does a simple rudimentary
calculation of the ranges freed.  The idea is to keep it simple at the
external shell script level and send in large chunks for now.
Signed-off-by: NManish Ahuja <mahuja@us.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This adds routines to
a. invalidate dump
b. calculate region that is reserved and needs to be freed.  This is
   exported through sysfs interface.

Unregister has been removed for now as it wasn't being used.
Signed-off-by: NManish Ahuja <mahuja@us.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Provide some basic debugging support.
Signed-off-by: NManish Ahuja <mahuja@us.ibm.com>
Signed-off-by: NLinas Vepstas <linasvepstas@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Set up the actual dump header, register it with the hypervisor.
Signed-off-by: NManish Ahuja <mahuja@us.ibm.com>
Signed-off-by: NLinas Vepstas <linasvepstas@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Check to see if there actually is data from a previously
crashed kernel waiting.  If so, allow user-space tools to
grab the data (by reading /proc/kcore).  When user-space
finishes dumping a section, it must release that memory
by writing to sysfs. For example,

  echo "0x40000000 0x10000000" > /sys/kernel/release_region

will release 256MB starting at the 1GB.  The released memory
becomes free for general use.
Signed-off-by: NLinas Vepstas <linasvepstas@gmail.com>
Signed-off-by: NManish Ahuja <mahuja@us.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Initial patch for reserving memory in early boot, and freeing it
later.  If the previous boot had ended with a crash, the reserved
memory would contain a copy of the crashed kernel data.
Signed-off-by: NManish Ahuja <mahuja@us.ibm.com>
Signed-off-by: NLinas Vepstas <linasvepstas@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

These items in asm-offsets.c are not used anywhere.  This removes them.
Signed-off-by: NRoland McGrath <roland@redhat.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The functions time_before, time_before_eq, time_after, and
time_after_eq are more robust for comparing jiffies against other
values.

This implements usage of the time_after() macro, defined at
linux/jiffies.h, which deals with wrapping correctly.
Signed-off-by: NS.Çağlar Onur <caglar@pardus.org.tr>
Acked-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The hypervisor can look at the value in the wait_state_cycles field of
the VPA for an estimate of how busy dedicated processors are.
Currently, as the kernel never touches this field, we appear to be
100% busy.  This records the duration the kernel is in powersave and
passes that to the HV to provide a reasonable indication of
utilisation.
Signed-off-by: NTony Breeds <tony@bakeyournoodle.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The PT_DTRACE flag is meaningless and obsolete.
Don't touch it.
Signed-off-by: NRoland McGrath <roland@redhat.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

It was being protected by CONFIG_PPC32, but we want to export it on
64-bit also.  This moves it out of the ifdef.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Some machines supported by the maple platform have an Obsidian
controller which can't be used without enabling CONFIG_IPR and the
options on which it depends.
Signed-off-by: NNathan Lynch <ntl@pobox.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This function has been a no-op for about 18 months; it's there in
the history should anyone need to resurrect it.
Signed-off-by: NNathan Lynch <ntl@pobox.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Prevailing practice for define_machine() in powerpc is to use the
platform name when the platform has only one define_machine()
statement, but maple uses "maple_md".  This caused me some
head-scratching when writing some new code that uses
machine_is(maple).

Use "maple" instead of "maple_md".  There should not be any behavioral
change -- fixup_maple_ide() calls machine_is(maple) but the body of
the function is ifdef'd out.
Signed-off-by: NNathan Lynch <ntl@pobox.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Print out 'model' property of '/' node as a machine name
in generic show_cpuinfo() routine.
Signed-off-by: NMarian Balakowicz <m8@semihalf.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The MDIO node in the lite5200b.dts file needs to also claim compatibility
with the older mpc5200 chip.  Otherwise the driver won't find the device.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The "bestcomm-core" driver defines its of_match table as follows

static struct of_device_id mpc52xx_bcom_of_match[] = {
	{ .type = "dma-controller", .compatible = "fsl,mpc5200-bestcomm", },
	{ .type = "dma-controller", .compatible = "mpc5200-bestcomm", },
	{},
};

so while registering the driver, the driver's probe function won't be
called, because the device tree node doesn't have a device_type
property.  Thus the driver's bcom_engine structure won't be allocated.
Referencing this structure later causes observed Oops.

Checking bcom_eng pointer for NULL before referencing data pointed
by it prevents oopsing, but fec driver still doesn't work (because
of the lost bestcomm match and resulted task allocation failure).
Actually the compatible property exists and should match and so
the fec driver should work.

This removes .type = "dma-controller" from the bestcomm driver's
mpc52xx_bcom_of_match table to solve the problem.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

If the bestcomm initialization fails, calls to the task allocate
function should fail gracefully instead of oopsing with a NULL deref.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The global primary_ipic in arch/powerpc/sysdev/ipic.c can remain NULL
if ipic_init() fails, which will happen on machines that don't have an
ipic interrupt controller.  init_ipic_sysfs() will crash in that case.
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

On pSeries, the hypervisor doesn't let us map in the eHEA ethernet
adapter using 64k pages, and thus the ehea driver will fail if 64k
pages are configured.  This works around the problem by always
using 4k pages for ioremap on pSeries (but not on other platforms).
A better fix would be to check whether the partition could ever
have an eHEA adapter, and only force 4k pages if it could, but this
will do for 2.6.25.

This is based on an earlier patch by Tony Breeds.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NPaul Mackerras <paulus@samba.org>

The PCI bridge representing the PCIE root complex on Axon, contains
device BARs for a memory range and ROM that define inbound accesses.
This confuses the kernel resource management code -- the resources
need to be hidden when Axon is a host bridge.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>