- 14 3月, 2011 1 次提交
-
-
由 Linus Walleij 提交于
This will configure the platform data for the PL180, PL011 and PL022 PrimeCells found in the U300 to use DMA with the generic PrimeCell DMA engine for COH 901 318. Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
-
- 25 10月, 2010 1 次提交
-
-
由 Linus Walleij 提交于
Just as it says, if this is merged along with the other patch, the driver supports the U300 NAND flash interface. Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
- 11 8月, 2010 2 次提交
-
-
由 Linus Walleij 提交于
This removes the quirks to clock the U300 VIC and timer by custom hooks and moves the control out to the clock framework where it belongs. This is possible now that clocks are available early. Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Linus Walleij 提交于
This fixes a regression due to the new apb_pclk stuff in the U300 platform, makes it run by splitting the apb clock off the single UART clocks. For the MMCI and PL022 clocks we don't split them: these are actually hardwired to the same clock terminal and will thus simply have a double reference count and will be referenced twice. We also move clock registration to .init_irq() so they are available early enough for probing to be successful and remove the earlier quirk to clock primecells during PrimeCell registration. Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 20 7月, 2010 1 次提交
-
-
由 Christoph Egger 提交于
MACH_U300_BS26 doesn't exist in Kconfig, therefore removing all references for it from the source code. Signed-off-by: NChristoph Egger <siccegge@cs.fau.de> Acked-by: NLinus Walleij <linus.walleij@stericsson.com> Signed-off-by: NJiri Kosina <jkosina@suse.cz>
-
- 15 2月, 2010 1 次提交
-
-
由 Linus Walleij 提交于
This fixes a few bugs in the DMA configuration for the COH 901 318 DMA engine used in U300. It also removes the directional parameter for each channel: separate DMA engine patches (submitted to the DMA engine maintainer) switches that mechanism over to using dynamic configuration of this, to handle bidirectional DMA channels. Cc: Dan Williams <dan.j.williams@intel.com> Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 09 2月, 2010 1 次提交
-
-
由 Daniel Mack 提交于
In particular, several occurances of funny versions of 'success', 'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address', 'beginning', 'desirable', 'separate' and 'necessary' are fixed. Signed-off-by: NDaniel Mack <daniel@caiaq.de> Cc: Joe Perches <joe@perches.com> Cc: Junio C Hamano <gitster@pobox.com> Signed-off-by: NJiri Kosina <jkosina@suse.cz>
-
- 28 1月, 2010 2 次提交
-
-
由 Linus Walleij 提交于
This changes the bus name of the U300 watchdog from just "wdog" to "coh901327_wdog" which is used to match the corresponding driver. This makes the watchdog probe properly. Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Linus Walleij 提交于
This adds platform configuration for the COH 901 318 DMA driver for the U300 series mobile platforms. Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 17 11月, 2009 1 次提交
-
-
由 Linus Walleij 提交于
This will fix some small issues with the COH 901 331 RTC driver: - Interrupt is disabled after alarm so that we don't fire multiple interrupts. - We return 0 from the coh901331_alarm_irq_enable() ridding a compile warning. - We alter the name in the U300 device registry to match that of the driver so they sucessfully resolve. Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 15 8月, 2009 3 次提交
-
-
由 Linus Walleij 提交于
The u300_init_check_chip() function was not properly tagged with the __init macro and provided a initsection mismatch on compilation. Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Linus Walleij 提交于
This sets up the U300 I2C subdevices so that the AB3100 analog baseband ASIC is properly detected and also the camera devices in the U335 reference design get properly registered. Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Linus Walleij 提交于
This adds a U300 board configuration for the PL022 SSP/SPI PrimeCell driver recently merged to the 2.6.31-rc series. Further it adds a dummy loopback SPI chip that can be used for testing the SPI functionality on a running system using the loopback mode of PL022. Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 09 7月, 2009 1 次提交
-
-
由 Linus Walleij 提交于
This makes the VIC resume from suspend flagged IRQ:s identical to the flags indicating all possible interrupts. This is perhaps not the optimal setting but setting it to 0 makes the system suspend and never come back again (all IRQ sources masked off). Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 29 4月, 2009 1 次提交
-
-
由 Linus Walleij 提交于
This adds core support for the ST-Ericsson U300 series platforms: U300, U330, U335 and U365. Supports memory mappings, interrupt controller, system timer (clocksource and clockevents), and binds to the existing drivers for the PrimeCells used in this design: PL190 (VIC), PL180 (MMC/SD host) and PL011 (UART). This is intented to serve as starting point for our mainling work, more patches to follow. Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-