1) Introduce ulpi specific flags for control of the ulpi phy
2) Extend the generic ulpi driver with support for Function and
Interface control of upli phy
3) Update the platforms using the generic ulpi driver with new ulpi
flags
4) Remove the otg control flags not in use
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The commit 9a763bfb "get rid of mxc_gpio_init" changed gpio_init
and irq_init sequence. Usually we will call set_irq_chained_handler
in gpio_init functions, this should be called after the irq_init
called, otherwise the chained irq can't get propoer irq_chip and this
irq will remain masked even we called set_irq_chained_handler.
Signed-off-by: NJason Wang <jason77.wang@gmail.com>
Tested-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

as per suggested by Sascha
Signed-off-by: NEric Bénard <eric@eukrea.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch fixes the following Kconfig warning :
"arch/arm/mach-mx25/Kconfig:18:warning: choice value used outside its
choice group
Signed-off-by: NEric Bénard <eric@eukrea.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NEric Bénard <eric@eukrea.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

In order to make this patch compile, even if the flexcan driver with
it's header defining the platform data isn't merged yet, two ifdefs have
been added. They effect that the "imx_add_flexcan" function results in a
no-op function if the driver hasn't been activated.

These ifdefs can be removed after the flexcan driver has been merged.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Because we add a 3ds debug board support in mxc level, we remove
those redundant codes from board level.
Signed-off-by: NJason Wang <jason77.wang@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

* cpuimx35 integrates i.MX35, RAM, NAND, Ethernet, I2C RTC, USB Host,
USB OTG and I2C touchscreen controller
* mbimxsd provides access to LCD, Audio, LED, Switch button, UART ...
Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

without this patch, ipu_clk's value is 0 thus preventing mx3fb from
calculating the right divisor for pixel clock generator.
Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Like this one (if CONFIG_USB_ULPI is not set):

arch/arm/mach-mx3/mach-pcm043.c:312: warning: 'otg_pdata' defined but not used
arch/arm/mach-mx3/mach-pcm043.c:317: warning: 'usbh1_pdata' defined but not used
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This makes the resistive touch interface work.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

arch/arm/mach-mx3/built-in.o: In function `mx31lilly_board_init':
mach-kzm_arm11_01.c:(.init.text+0x674): undefined reference to `otg_ulpi_create'
mach-kzm_arm11_01.c:(.init.text+0x68c): undefined reference to `otg_ulpi_create'
mach-kzm_arm11_01.c:(.init.text+0x744): undefined reference to `mxc_ulpi_access_ops'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

moboard_uart0_init requests a gpio.   Without an exit function that
frees that gpio again binding the uart a second time doesn't work.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Make use of new mechanism to register a nand device.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Make use of new mechanism to register a nand device.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

As the kernel contains a copy of the GPL anyhow just get rid of the address
specification instead of fixing it.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

This function is defined once for each imx family and so is in the way
when compiling a kernel for more than one SoC.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Moreover remove unused definitions.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Moreover remove unused definitions.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

board-qong.h only defined a single symbol that was used only once.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Additional document all known names of that machine.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Add two RGB led on mx31moboard using MC13783 led subsystem
Signed-off-by: NPhilippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

CC      arch/arm/mach-mx3/mach-pcm037.o
  arch/arm/mach-mx3/mach-pcm037.c: In function 'mxc_board_init':
  arch/arm/mach-mx3/mach-pcm037.c:584: warning: unused variable 'tmp'
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NAlberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch adds also the pin definition helpers in iomux-mx3.h
Signed-off-by: NAlberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The member "clock" of struct "sja1000_platform_data" is documented as
"CAN bus oscillator frequency in Hz" but it's actually used as the CAN
clock frequency, which is half of it. To avoid further confusion, this
patch fixes it by renaming the member to "osc_freq". That way, also
non mainline users will notice the change. The platform code for the
relevant boards is updated accordingly. Furthermore, pre-defined
values are now used for the members "ocr" and "cdr".
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Tested on actual hardware using the g_ether and g_serial gadget drivers.
Signed-off-by: NMagnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>