On OMAP4 SOC, intecronnects has many write buffers in the async bridges
and they need to be drained before CPU enters into standby state.

Patch 'OMAP4: PM: Add CPUX OFF mode support' added CPU PM support
but OMAP errata i688 (Async Bridge Corruption) needs to be taken
care to avoid issues like system freeze, CPU deadlocks, random
crashes with register accesses, synchronisation loss on initiators
operating on both interconnect port simultaneously.

As per the errata, if a data is stalled inside asynchronous bridge
because of back pressure, it may be accepted multiple times, creating
pointer misalignment that will corrupt next transfers on that data
path until next reset of the system (No recovery procedure once
the issue is hit, the path remains consistently broken).
Async bridge can be found on path between MPU to EMIF and
MPU to L3 interconnect. This situation can happen only when the
idle is initiated by a Master Request Disconnection (which is
trigged by software when executing WFI on CPU).

The work-around for this errata needs all the initiators
connected through async bridge must ensure that data path
is properly drained before issuing WFI. This condition will be
met if one Strongly ordered access is performed to the
target right before executing the WFI. In MPU case, L3 T2ASYNC
FIFO and DDR T2ASYNC FIFO needs to be drained. IO barrier ensure
that there is no synchronisation loss on initiators operating
on both interconnect port simultaneously.

Thanks to Russell for a tip to conver assembly function to
C fuction there by reducing 40 odd lines of code from the patch.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NRichard Woodruff <r-woodruff2@ti.com>
Acked-by: NJean Pihet <j-pihet@ti.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Tested-by: NVishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

This patch selects ARM_AMBA if OMAP3_EMU is defined because
OC_ETM depends on ARM_AMBA, so fix the link failure[1].

[1],
arch/arm/kernel/built-in.o: In function `etm_remove':
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:609: undefined
reference to `amba_release_regions'
arch/arm/kernel/built-in.o: In function `etb_remove':
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:409: undefined
reference to `amba_release_regions'
arch/arm/kernel/built-in.o: In function `etm_init':
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:640: undefined
reference to `amba_driver_register'
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:646: undefined
reference to `amba_driver_register'
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:648: undefined
reference to `amba_driver_unregister'
arch/arm/kernel/built-in.o: In function `etm_probe':
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:545: undefined
reference to `amba_request_regions'
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:595: undefined
reference to `amba_release_regions'
arch/arm/kernel/built-in.o: In function `etb_probe':
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:347: undefined
reference to `amba_request_regions'
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:392: undefined
reference to `amba_release_regions'
arch/arm/mach-omap2/built-in.o: In function `emu_init':
/home/tom/git/omap/linux-2.6-omap/arch/arm/mach-omap2/emu.c:62:
undefined reference to `amba_device_register'
/home/tom/git/omap/linux-2.6-omap/arch/arm/mach-omap2/emu.c:63:
undefined reference to `amba_device_register'
make: *** [.tmp_vmlinux1] Error 1
making modules
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NTony Lindgren <tony@atomide.com>

Now that MULTI_IRQ_HANDLER is selected by all the in-tree
GIC users, make it mandatory and remove the unused macros.
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Convert the omap2plus platforms to be using CONFIG_MULTI_IRQ_HANDLER.
Each machine is modified to provide either omap2_intc_handle_irq(),
omap3_intc_handle_irq() or gic_handle_irq().

This allows for a major cleanup, removing the MULTI_OMAP setup
from the interrupt path.

Tested on both Panda and IGEPv2 (single kernel image)
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

We currently have two symbols to control compilation the MFD subsystem,
MFD_SUPPORT and MFD_CORE. The MFD_SUPPORT is actually not required
at all, it only hides the submenu when not set, with the effect that
Kconfig warns about missing dependencies when another driver selects
an MFD driver while MFD_SUPPORT is disabled. Turning the MFD submenu
back from menuconfig into a plain menu simplifies the Kconfig syntax
for those kinds of users and avoids the surprise when the menu
suddenly appears because another driver was enabled that selects this
symbol.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Re-cycle the original board-generic.c file to support Device Tree
for every OMAP2+ variants.

The current approach is an intermediate step before having only
one machine descriptor that will use some generic DT aware
functions.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>

Support for the cpu_suspend functions is only built-in
when CONFIG_PM_SLEEP is enabled, but omap3/4, exynos4
and pxa always call cpu_suspend when CONFIG_PM is enabled.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

CONFIG_PM is no longer a user-selectable Kconfig option.  Rather it is
automatically enabled if either CONFIG_SUSPEND or CONFIG_RUNTIME_PM is
enabled, so having a 'select PM' here is redunant when 'select
CONFIG_PM_RUNTIME' is present.
Signed-off-by: NKevin Hilman <khilman@ti.com>

cm-t3730 is basically the same board as cm-t35,
but has AM/DM3730 SoC assembled and therefore some changes are required.
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Acked-by: NMike Rapoport <mike@compulab.co.il>
[tony@atomide.com: updated for init_irq cleanup as noted by khilman@ti.com]
Signed-off-by: NTony Lindgren <tony@atomide.com>

since it is merged into board-igep0020.c
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Populate the l2x0 set_debug function pointer with OMAP secure call
and enable the PL310 Errata 727915

This patch has dependency on the earlier patch
ARM: l2x0: Errata fix for flush by Way operation can cause data
corruption
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

On OMAP4430 ES1.0 the local timers are gated by security. Enable the
CONFIG_LOCAL_TIMERS for omap2plus build and handle the OMAP4430 es1.0
exception case.

This patch has dependency on the first patch in this series.
	ARM: smp: Select local timers vs dummy timer support runtime
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Power to the wl12xx wlan device is controlled by a fixed regulator.
Boards that have the wl12xx should select REGULATOR_FIXED_VOLTAGE.
Signed-off-by: NPanduranga Mallireddy <panduranga_mallireddy@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds minimal support and build configuration for TI816X EVM.
Signed-off-by: NHemant Pedanekar <hemantp@ti.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch updates the common platform files with TI816X support.

The approach taken in this patch is to add TI816X as part of OMAP3 variant where
the cpu class is considered as OMAP34XX and the type is TI816X. This means, both
cpu_is_omap34xx() and cpu_is_ti816x() checks return success on TI816X.

A kernel config option CONFIG_SOC_OMAPTI816X is added under OMAP3 to include
support for TI816X build.
Signed-off-by: NHemant Pedanekar <hemantp@ti.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

We want to have just CONFIG_ARCH_OMAP2, 3 and 4. The rest
are nowadays just subcategories of these.

Search and replace the following:

ARCH_OMAP2420		SOC_OMAP2420
ARCH_OMAP2430		SOC_OMAP2430
ARCH_OMAP3430		SOC_OMAP3430

No functional changes.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NThomas Weber <weber@corscience.de>
Acked-by: NSourav Poddar <sourav.poddar@ti.com>

This patch adds OPP tables for OMAP4. New file has been added to keep
the OMAP4 opp tables and the registration of these tables with the
generic opp framework by OMAP SoC OPP interface.

Based on:
http://dev.omapzoom.org/?p=santosh/kernel-omap4-base.git;a=blob;f=arch/arm/mach-omap2/opp44xx_data.c;h=252e3d0cb6050a64f390b9311c1c4977d74f762a;hb=refs/heads/omap4_nextSigned-off-by: NThara Gopinath <thara@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Add OPP data for OMAP34xx and OMAP36xx and initialization functions
to populate OPP tables based on current SoC.
introduce an OMAP generic opp initialization routine which OMAP3
and OMAP4+ SoCs can use to register their OPP definitions.

Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

There is no MFD config option, MFD_SUPPORT should be selected instead.
This will prevent build errors when trying out different configurations.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Power to the wl12xx wlan device is controlled by a fixed regulator.

Boards that have the wl12xx should select REGULATOR_FIXED_VOLTAGE so
users will not be baffled.
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add minimal support for Nokia RM-680 board.

Tested with omap2plus_defconfig.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
[tony@atomide.com: updated to remove omap_gpio_init
Signed-off-by: NTony Lindgren <tony@atomide.com>

This should be only selected in CONFIG_ARCH_OMAP2PLUS_TYPICAL
to make it easy to disable.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Craneboard is a hardware development platform based on the
Sitara AM3517 ARM Cortex - A8 microprocessor device. This is a
low cost reference design.

This patch adds basic board file. Detailed support will follow in
subsequent patches.

  [1] http://www.ti.com/arm
  [2] http://www.mistralsolutions.com/products/craneboard.phpSigned-off-by: NSrinath <srinath@mistralsolutions.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The OMAP4 has an on-chip EHCI controller. Select USB_ARCH_HAS_EHCI
to allow the EHCI driver to be built on OMAP4.
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

The mux framework allows the change of pad configuration by drivers
when needed. Prior to this the mux framework has to be initialised
with all the mux parameters specific to the board. The mux init is
already present in the board file for SDP. Adding the mux init
for panda boards.
Signed-off-by: Nsricharan <r.sricharan@ti.com>
Acked-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>

Select the CBS package if SDP4430 is enabled during config.
Use the proper package (CBL or CBS) based on chip revision.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>

Please note that the full muxmodes are re-defined for ES2 instead
of using the subset. There are 81 differences among 204 pins.
The subset fixup will have to iterate over the whole list for each
subset entry, which can lead to an important number of iteration.
On the other hand, it will take much more memory at boot time.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>

Select the CBL package if SDP4430 is enabled during config.
Initialize the mux framework during the board init.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>

Add data for OMAP4430 generated from HW pinout & register database.
The data set is split in two partitions for both core and wkup.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>

Currently, if, for example, CONFIG_ARCH_OMAP2420 is not selected, OMAP2420
board files can still be included in the build.  This results in link errors:

arch/arm/mach-omap2/built-in.o: In function `omap_generic_map_io':
.../arch/arm/mach-omap2/board-generic.c:51: undefined reference to `omap2_set_globals_242x'
arch/arm/mach-omap2/built-in.o: In function `omap_h4_init':
.../arch/arm/mach-omap2/board-h4.c:330: undefined reference to `omap2420_mux_init'
arch/arm/mach-omap2/built-in.o: In function `omap_h4_map_io':
.../arch/arm/mach-omap2/board-h4.c:373: undefined reference to `omap2_set_globals_242x'
arch/arm/mach-omap2/built-in.o: In function `omap_apollon_init':
.../arch/arm/mach-omap2/board-apollon.c:325: undefined reference to `omap2420_mux_init'
arch/arm/mach-omap2/built-in.o: In function `omap_apollon_map_io':
.../arch/arm/mach-omap2/board-apollon.c:353: undefined reference to `omap2_set_globals_242x'
make: *** [.tmp_vmlinux1] Error 1

Fix this by making the boards depend on the Kconfig option for the
specific SoC that they use.

Also, while here, fix the mach-omap2/board-generic.c file to remove the
dependency on OMAP2420.

Charulatha Varadarajan <charu@ti.com> caught a typo - thanks Charu.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Charulatha Varadarajan <charu@ti.com>

The OMAP3 IGEP module is a low-power, high performance production-ready
system-on-module (SOM) based on TI's OMAP3 family. More about this
board at www.igep.es.
Signed-off-by: NEnric Balletbo i Serra <eballetbo@gmail.com>
[tony@atomide.com: updated for the mmc changes and to be selected by default]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Enable omap-serial driver in /mach-omap2/Kconfig and
move 8250 driver selection for zoom boards. With omap-serial
driver addition all omap-uarts can be handled with
omap-serial driver.

With addition of omap-serial driver console parameter
needs be changed in bootargs from ttyS* should be
replaced with ttyO* [O --> OMAP not ZERO]

For example: ttyS0[UART1 on 3430SDP] changes to ttyO0.

But with some boards that do not use omap-uart as console uart.
we need to handle them with 8250 driver. Ex: ZOOM2/3.
For zoom2/3 board we need to use 8250 serial driver and
console parameter will remain ttyS0 which basically uses
a Quad uart placed on the debug board connected through a
gpio line.
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Adding support for LogicPD's OMAP 3530 LV SOM and
OMAP 35x Torpedo board.
Signed-off-by: NTim Nordell <tim.nordell@logicpd.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add basic suppot, enable uart and led.
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch addresses below things

- Renaming existing omap3_defconfig which has OMAP2, OMAP3 and OMAP4 builds
  enabled to more appropriate name 'omap2plus_defconfig'
- L1 cache shift is suppose to be 5 on OMAP4 where as it is 6 on previous
  OMAPs. Keeping it to 5 is safer option for OMAP4 and previous OMAPs. For
  OMAP3 only build the shift would be still 6
- Enable needed Errata's for OMAP4 to work with DMA based device drivers
	CONFIG_PL310_ERRATA_588369=y
	CONFIG_ARM_ERRATA_720789=y
- Enable the Micrel ethernet controller
	CONFIG_KS8851=y
	CONFIG_KS8851_MLL=y

With above three changes, OMAP4 ethernet, mmc etc works reliably.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add initial support for the OMAP4 based Panda Board.
Signed-off-by: NDavid Anders <x0132446@ti.com>
[tony@atomide.com: selected board by default in Kconfig]
Signed-off-by: NTony Lindgren <tony@atomide.com>

This produces a sane config that's suitable for using as the
base for most omap2/3/4 boards.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Select all omaps and boards by default
Signed-off-by: NTony Lindgren <tony@atomide.com>

Move omap2/3/4 specific Kconfig options to mach-omap2/Kconfig
Signed-off-by: NTony Lindgren <tony@atomide.com>

This will make Kconfig look nicer for selecting omap processor type
Signed-off-by: NTony Lindgren <tony@atomide.com>