Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

cx18: Reduce number of mmio read retries to improve performance.  Experiments
have shown 2 things: read retries never improve the result of a suspect mmio
read from the CX23418 (the result stays all 0xff's), and that most of the
suspected read failures are actually proper reads of values that should be
all 0xff's.  This change reduces the number of read retries and keeps the
count separate from write retries.
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Note:
* At High Symbol Rates we do not have enouph machine cycles to handle the
  incoming symbols and hence might run into problems at the very end of the
  specified definition
* Most of the equations have been calculated for a master clock of 99 MHz,
  running at 90MHz, raises lot of issues such as the need to recalculate
  all of them , which is eventually very painful.
Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Print manufacturer/product info from USB device and also card entry.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Prints usb speed used by em28xx interface. While there, fixes USB ID's
endiannes.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Several chips may be turned off when the device is not used, like audio,
video and dvb demods. This patch adds a gpio callback at the core
structs to allow turning off such devices.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

A previous changeset moved gpio from em28xx struct into em28xx_board.
However, the driver were not updated to properly honor those gpio's.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Before this patch, several devices without tuner were kept the value 0
for tuner_type. However, this means TUNER_TEMIC_PAL. Replace those
entries for the proper TUNER_ABSENT value.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Instead of using magic vmux/amux, let's use an alias where possible.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Instead of a large, ugly switch specifying the gpio tables for each
device, let's move it into the boards struct. This also helps to see
what boards have already the gpio's for DVB.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Replaces all occurrences of em28xx_write_regs_req() and em28xx_write_reg()
used to setup register names by em28xx_write_reg().

Also, documents the register names that are known.

This patch were generated by this small perl script:

my %reg_map = (
	# Register table - the same as defined on parse_em28xx.pl script
);

while (<>) {
	if (m/(.*)em28xx_write_regs_req\(dev\,\s*0x00\,\s*(.*)\,\s*\"\\x(..)\",\s*1\)\;(.*)/) {
		my $reg = $2;
		my $val = $3;
		$val =~ tr/A-f/a-f/;
		$reg = $reg_map{$reg} if defined($reg_map{$reg});
		printf "$1em28xx_write_reg(dev, %s, 0x%s);$4\n", $reg, $val;
	} elsif (m/(.*)em28xx_write_regs\(dev\,\s*(.*)\,\s*\"\\x(..)\",\s*1\)\;(.*)/) {
		my $reg = $2;
		my $val = $3;
		$val =~ tr/A-f/a-f/;
		$reg = $reg_map{$reg} if defined($reg_map{$reg});
		printf "$1em28xx_write_reg(dev, %s, 0x%s);$4\n", $reg, $val;
	} else {
		print $_;
	}
}
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Now, the first message states board names. Also, removed printing the alternate
settings by default. I2C messages are now clearer.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Since saa7115 has saa711x chip auto-detection, there's no need on differenciating
it at cards table. Just use the generic name for all boards that use a philips
saa711x decoder.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Several fields are duplicated on both structs. Let's just copy em28xx_board instead.

A later cleanup could just copy the fields that are changed, in order to keep em28xx_board
const.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove unused em28xx_board.vchannels and em28xx.video_channels.
Also, .is_em2800 = 0 is not needed, as all data is zeroed by kernel loader.

The table also included a notice that svideo weren't test on Hauppauge
USB2. Remove this notice, since this input also works properly.

Also, it does some whitespace cleanups.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The previous patches removed XCLK and I2C magic. Now, we finally know
what those registers do. Also, only a very few cards need different
setups for those.

Instead of keeping the setups for those values inside the per-device
hack magic switch, move the uncommon values to the board-specific
struct, and have a common setup for all other boards.

So, almost 100 lines of hacking magic were removed.

A co-lateral effect of this patch is that it also fixes a bug at em28xx-core, where xclk
were set, without taking any care about not overriding a previous xclk setup.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Cleanup the calls to set the GPIOs and GPOs for various devices,
replacing the register number with the #define from em28xx-reg.h and
converting over to using em28xx_write_reg()
Signed-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert over to setting the XCLK register usage with the new em28xx_write_reg()
function.

Thanks to Ray Lu from Empia for providing the em2860/2880 datasheet.
Signed-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch provides USB suspend and hibernation support
for Siano's SMS chipset based USB device
Signed-off-by: NUri Shkolnik <uris@siano-ms.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add function smsdvb_read_ucblocks to report uncorrectable error counts.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Enable power LED while the frontend is in use.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

add USB IDs for Hauppauge WinTV MiniCard DVB-T
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

On some em28xx devices, there's an unused interface. This is printed on
the logs as an error. We can just ignore that interface.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The OmniVision OV534 is the USB bridge chip used in Sony Playstation EYE,
it is found also in other webcams like Hercules Blog Webcam and
Hercules Dualpix HD.
This driver is the port to gspca of a prototype driver by Mark Ferrell
based on vivi. The original code to initialize the camera and start the
capture is from Jim Paris on ps2dev.org, here integrated with the analysis
of the USB communications taken by the windows driver.
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The sn9c105 and sn9c120 bridges must be differently programmed for the ov7660.
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (9703): Move the s5k4aa vflip quirk table to the main sensor file in order to avoid compilation errors on older kernels
Signed-off-by: NErik Andrén <erik.andren@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NErik Andrén <erik.andren@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NErik Andrén <erik.andren@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>