Rockchip RK3288 hdmi is compatible with dw_hdmi
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
Tested-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>

RK3288 HDMI will not work without the spare bit of
HDMI_PHY_CONF0 enable
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
Tested-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>

HDMI_IH_I2CMPHY_STAT0 is a clear on write register, which indicates i2cm
operation status(i2c transfer done or error), every hdmi phy register
configuration must check this register to make sure the configuration
has complete. But the indication bit should be cleared after check, otherwise
the corresponding bit will hold on forever, this may give a wrong signal for
next check.
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
Tested-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>

some platform may not support all the display mode,
add mode_valid interface check it
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
Tested-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>

On rockchip rk3288, only word(32-bit) accesses are
permitted for hdmi registers.  Byte width accesses (writeb,
readb) generate an imprecise external abort.
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
Tested-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>

the original imx hdmi driver is under drm/imx/,
which depends on imx-drm, so move the imx hdmi
driver out to drm/bridge and rename it to dw_hdmi
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
Tested-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>

hdmi phy configuration is platform specific, which can be adjusted
according to the board to get the best SI
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
Tested-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>

IMX6 and Rockchip RK3288 and JZ4780 (Ingenic Xburst/MIPS)
use the interface compatible Designware HDMI IP, but they
also have some lightly differences, such as phy pll configuration,
register width, 4K support, clk useage, and the crtc mux configuration
is also platform specific.

To reuse the imx hdmi driver, convert it to drm_bridge

handle encoder in imx-hdmi_pltfm.c, as most of the encoder
operation are platform specific such as crtc select and
panel format set

This patch depends on Russell King's patch:
 drm: imx: convert imx-drm to use the generic DRM OF helper
 http://driverdev.linuxdriverproject.org/pipermail/driverdev-devel/2014-July/053484.htmlSigned-off-by: NAndy Yan <andy.yan@rock-chips.com>
Signed-off-by: NYakir Yang <ykk@rock-chips.com>
Tested-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>

drm driver may probe before the i2c bus, so the driver should
defer probing until it is available
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
Reviewed-by: NDaniel Kurtz <djkurtz@chromium.org>
Tested-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>

CHECK: Alignment should match open parenthesis
+       if ((hdmi->vic == 10) || (hdmi->vic == 11) ||
+               (hdmi->vic == 12) || (hdmi->vic == 13) ||

CHECK: braces {} should be used on all arms of this statement
+       if (hdmi->hdmi_data.video_mode.mdvi)
[...]
+       else {
[...]
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
Reviewed-by: NDaniel Kurtz <djkurtz@chromium.org>
Tested-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>

The functions ipu_dc_enable() and ipu_dc_disable() enable/disable the DC
globally in the IPU_CONF register, but the DC is used by multiple clients
on different DC channels. So make sure to only disable/enable the DC
globally based on a use counter.
Signed-off-by: NSteve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>

Use the generic DRM OF helper to locate the possible CRTCs for the
encoder, thereby shrinking the imx-drm driver some more.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>

If edid was allocated during bind, it must be freed again during unbind.
Signed-off-by: NPeter Seiderer <ps.report@gmx.net>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>

If edid was allocated during bind, it must be freed again during unbind.
Signed-off-by: NPeter Seiderer <ps.report@gmx.net>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>

When compiling in module some symbol aren't missing,
export them correctly.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Should probably just init this in the GMbus code all the time, based on
the cdclk and HPLL like we do on newer platforms.  Ville has code for
that in a rework branch, but until then we can fix this bug fairly
easily.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76301Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: NNikolay <mar.kolya@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

When bind failed make sure that CRTC and planes are
completely clean up to avoid properties duplication.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>

High Quality Video Data Plane is hardware IP dedicated
to video rendering. Compare to GPD (graphic planes) it
have better scaler capabilities.

HQVDP use VID layer to push data into hardware compositor
without going into DDR. From data flow point of view HQVDP
and VID are nested so HQVPD update/disable VID.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>

stih407 SoC have a dedicated hardware cursor plane,
this patch enable it.
The hardware have a color look up table, fix it to
be able to use ARGB8888.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>

For stih407 SoC enable the second mixer to get two CRTC.
Allow GPD planes and encoders to be connected to this new CRTC.
Cursor plane can only be set on first CRTC.
GPD clocks needed change the parent clock depending on which
CRTC GPD are used.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>

The HDMI path introduce a delay of 6 pixels.
This delay should be take into account while programming
VTG for the HDMI. Without this delay, the HDMI active
window area is shift of 6 pixel on the right.

Set also timing for DVO output.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>

Change some functions prototype to prepare the introduction of
auxiliary crtc. It will also help to have a DVO encoder.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>

Make sure that vblank is enabled when crtc commit is call.
Replace drm_vblank_off() by drm_crtc_vblank_off()
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>

The hardware expect to have the infoframe checksum in the first byte.
In consequence shift all infoframe on one byte.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>

Stop use event_lock in vblank disable function.
This was creating a dead lock.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>

Store the physical address at node creation time
to avoid use of virt_to_dma and dma_to_virt everywhere
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>

Make sure that mixer control register is correctly reset
before use it.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>

gpio used for HDMI hot plug detection is useless,
HDMI_STI register contains an hot plug detection status bit.
Fix binding documentation.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>

Depending of the board configuration i2c for ddc could change,
this patch allow to use a phandle to specify which i2c controller to use.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>

We may be hidding bugs by doing that, so let remove it and have the
actual mask value shine through, for better or worse.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

While trying to unify the order of those arguments throughout the
driver, Daniel noticed what we were inverting them in this part of the
code.
Suggested-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Drivers where the DRM objects have a lifetime that extends beyond that
of the DRM device need to zero out the DRM object memory to void stale
data such as properties. The DRM core code expects to operate on newly
allocated and zeroed out objects and will behave unexpectedly, such as
add duplicate properties, otherwise.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

I was playing with clang and oh surprise! a warning trigerred by
-Wshift-overflow (gcc doesn't have this one):

    WA_SET_BIT_MASKED(GEN7_GT_MODE,
                      GEN6_WIZ_HASHING_MASK | GEN6_WIZ_HASHING_16x4);

    drivers/gpu/drm/i915/intel_ringbuffer.c:786:2: warning: signed shift result
      (0x28002000000) requires 43 bits to represent, but 'int' only has 32 bits
      [-Wshift-overflow]
        WA_SET_BIT_MASKED(GEN7_GT_MODE,
        ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    drivers/gpu/drm/i915/intel_ringbuffer.c:737:15: note: expanded from macro
      'WA_SET_BIT_MASKED'
        WA_REG(addr, _MASKED_BIT_ENABLE(mask), (mask) & 0xffff)

Turned out GEN6_WIZ_HASHING_MASK was already shifted by 16, and we were
trying to shift it a bit more.

The other thing is that it's not the usual case of setting WA bits here, we
need to have separate mask and value.

To fix this, I've introduced a new _MASKED_FIELD() macro that takes both the
(unshifted) mask and the desired value and the rest of the patch ripples
through from it.

This bug was introduced when reworking the WA emission in:

  Commit 7225342a
  Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
  Date:   Tue Oct 7 17:21:26 2014 +0300

      drm/i915: Build workaround list in ring initialization

v2: Invert the order of the mask and value arguments (Daniel Vetter)
    Rewrite _MASKED_BIT_ENABLE() and _MASKED_BIT_DISABLE() with
    _MASKED_FIELD() (Jani Nikula)
    Make sure we only evaluate 'a' once in _MASKED_BIT_ENABLE() (Dave Gordon)
    Add check to ensure the value is within the mask boundaries (Chris Wilson)

v3: Ensure the the value and mask are 16 bits (Dave Gordon)

Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Apparently stuff works that way on those machines.

I agree with Chris' concern that this is a bit risky but imo worth a
shot in -next just for fun. Afaics all these machines have the pci
resources allocated like that by the BIOS, so I suspect that it's all
ok.

This regression goes back to

commit eaba1b8f
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Thu Jul 4 12:28:35 2013 +0100

    drm/i915: Verify that our stolen memory doesn't conflict

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76983
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=71031Tested-by: Nlu hua <huax.lu@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NPaul Menzel <paulepanter@users.sourceforge.net>
Cc: stable@vger.kernel.org
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Spotted while reviewing the DRM changes in Linux 3.18 for LinuxFR.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMartin Peres <martin.peres@free.fr>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Spotted while reviewing the DRM changes in Linux 3.18 for LinuxFR.

CC: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NMartin Peres <martin.peres@free.fr>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This adds fbdev/con support for tiled monitors, so that we
only set a mode on the correct half of the monitor, or
span the two halves if needed.

v2: remove unneeded ERROR, fix | vs ||
Signed-off-by: NDave Airlie <airlied@redhat.com>

This takes the tiling info from the connector and
exposes it to userspace, as a blob object in a
connector property.

The contents of the blob is ABI.

v2: add property + function documentation.

v3: move property setup from previous patch.
add boilerplate + fix long line (Daniel)
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This creates a tile group from DisplayID block, and
stores the pieces of parsed info from the DisplayID block
into the connector.

v2: add missing signoff, add new connector bits to docs.

v3: remove some debugging.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Logical ports are never going to have EDID changes,
they are used for the internal ports on MST monitors.

We cache the EDIDs from these to save time at MST probe.

v2: drop misplace tile property line, meant for other patch.
Signed-off-by: NDave Airlie <airlied@redhat.com>