It was brought to our attention that the prefetches break e1000 traffic
on xscale/arm architectures.  Remove them for now.  We'll let them
stay in mm for a while, or find a better solution to enable.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

New code added in 2.6.17 caused setup_irq to print a warning when
running ethtool -t eth0 offline.

This test marks the request_irq call made by this test as a "probe"
to see if the interrupt is shared or not.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

skb_clone() may fail, we should check the result.

Coverity CID: 1215.
Signed-off-by: NFlorin Malita <fmalita@gmail.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From: Matt Mackall <mpm@selenic.com>

netconsole is being wrong here.  If it wasn't enabled there's no error.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From: Zachary Amsden <zach@vmware.com>
Signed-off-by: NZachary Amsden <zach@vmware.com>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

From: Florin Malita <fmalita@gmail.com>

The skb may be gone after netif_rx(), we can't use 'skb->len' to update the
stats.  'pkt_len' should work instead.

Coverity CID: 911.
Signed-off-by: NFlorin Malita <fmalita@gmail.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Also add the Poll RX DMA Memory workaround to the DMA4
(xmitstatus) path.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During a code scan for another change I discovered that this call to
pcnet32_free_ring must be removed.  If the open fails due to a lack of
memory all the ring structures are removed via the call to free_ring
and a subsequent call to open will dereference a null pointer in
pcnet32_init_ring.

Please apply to 2.6.17.
Signed-off-by: NDon Fry <brazilnut@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Someone was waaay too aggressive and removed e1000's reboot notifier
instead of porting it to the new way of the shutdown handler.  This change
broke wake on lan.  Add the shutdown handler back in using the same method
as e100 uses.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

(cherry picked from c653e635 commit)

Fix section mismatch warnings:
WARNING: drivers/net/wireless/arlan.o - Section mismatch: reference to
.init.text:arlan_probe from .text between 'init_module' (at offset
0x3526) and 'cleanup_module'
WARNING: drivers/net/wireless/arlan.o - Section mismatch: reference to
.init.text:init_arlan_proc from .text between 'init_module' (at offset
0x3539) and 'cleanup_module'
WARNING: drivers/net/wireless/arlan.o - Section mismatch: reference to
.exit.text:cleanup_arlan_proc from .text between 'cleanup_module' (at
offset 0x356c) and 'arlan_diagnostic_info_string'
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix section mismatch warning:
WARNING: drivers/net/wireless/wavelan.o - Section mismatch: reference to
.init.text: from .text between 'init_module' (at offset 0x371e) and
'cleanup_module'
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If a SIR dongle is built in the kernel while IRTTY_SIR is built
as a module, kernel compilation will fail.
Thus, the SIR dongle config should depend on the IRTTY_SIR.

Closes kernel bug# 6512
(http://bugzilla.kernel.org/show_bug.cgi?id=6512)
Signed-off-by: NSamuel Ortiz <samuel@sortiz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The truncate threshold calculation to prevent receiver from getting stuck
was incorrect, and it didn't take into account the upper limit on bits
in the register so the jumbo packet support was broken.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

If the skb allocation fails, the current error path calls
dev_kfree_skb_irq() with a NULL argument.  Also, 'err' is not being used.

Coverity CID: 275.
Signed-off-by: NFlorin Malita <fmalita@gmail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Use kmalloc() instead of a local array in bnx2_nvram_write().

Update version to 1.4.40.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a bug in bnx2_nvram_write() caused by a counter variable not
correctly incremented by 4.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add some missing rx error counters for 5705 and newer chips.

Update version to 3.58.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With Manfred Spraul <manfred@colorfullife.com> and
     Andrew Morton <akpm@osdl.org>

Bring back this recently-reverted patch, only fixed.

Original changelog:

    From: Ayaz Abdulla <aabdulla@nvidia.com>

    This patch fixes the issues with multiple irqs.

    I am resending based on feedback. I decoupled the dma mask for
    consistent memory and fixed leak with multiple irq in error path.

    Thanks to Manfred for catching the spin lock problem.

Fix it:

    From: Manfred Spraul <manfred@colorfullife.com>

    Fix bug introduced by ebf34c9b, covered in
    http://bugzilla.kernel.org/show_bug.cgi?id=6568.

    Remove second instance of the request_irq() calls: they were moved
    from nv_open into nv_request_irq.

    Thanks to Alistair Strachan <alistair@devzero.co.uk> for reporting and
    persisting.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NManfred Spraul <manfred@colorfullife.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Call pci_map_single() with the actual size of the receive
buffers, not 0 (which skb->len is initialized to by dev_alloc_skb()).
Signed-off-by: NErling A. Jacobsen <linuxcub@email.dk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Dear Jeff

axnet_cs: bug fix multicast code (support older ax88190 chipset)

Signed-off-by: komurojun-mbn@nifty.com

Best Regards
Komuro
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The driver will get stuck (permanent transmit timeout), if the transmit
ring size is set too small.  It needs to have enough ring elements to
hold one maximum size transmit.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Skge driver always causes  bad checksums on big-endian.
The checksum in the receive control block was being swapped
when it doesn't need to be.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Need to track impact of this group of changes.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

If the status ring processing can't keep up with the incoming frames,
it is more efficient to have NAPI keep scheduling the poll routine
rather than causing another interrupt.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Logic error in the phy initialization code. Also, turn on wake on lan
bit in status control.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The Dlink DGE-560T uses Yukon2 chipset so it needs sky2 driver; and
the DGE-530T uses Yukon1 so it uses skge driver.

Bug: http://bugzilla.kernel.org/show_bug.cgi?id=6544Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

If both ports are receiving on the SysKonnect dual port cards,
then it appears the bus interface unit can give an interrupt status
for frame before DMA has completed.  This leads to bogus frames
and general confusion. This is why receive checksumming is also
messed up on dual port cards.

A workaround for the out of order receive problem is to eliminating
split transactions on PCI-X.

This version is based of the current linux-2.6.git including earlier
patch to disable dual ports.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Revert previous patch with subject "change mdelay to msleep and remove
from ISR path".  This patch seems to have caused bigger problems than
it solved, and it didn't solve much of a problem to begin with...

Discussion about backing-out this patch can be found here:

	http://marc.theaimsgroup.com/?l=linux-netdev&m=114321570402396&w=2

The git commit associated w/ the original patch is:

	6ba98d31

Signed-off-by: John W. Linville <linville@tuxdriver.com
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Revert ebf34c9b.  Maybe.  Due to crashes
at shutdown - see http://bugzilla.kernel.org/show_bug.cgi?id=6568.

Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

I still need this hack to work around the fact that softmac doesn't
attempt to associate when we bring the device up...
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Needed for interaction with the nommu code in x86-64 which
will return bad_dma_address if the address exceeds dma_mask.

Cc: netdev@vger.kernel.org
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

When both ports are receiving simultaneously, the receive logic gets confused
and may pass up a packet before it is full. This causes hangs, and IP will see
lots of garbage packets. There is even the potential for data corruption if
a later arriving packet DMA's into freed memory.

It looks like a hardware bug because status arrives for a packet but no
data is there. Until this bug is worked out, block the user from bringing
up both ports at once.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Needed for interaction with the nommu code in x86-64 which
will return bad_dma_address if the address exceeds dma_mask.

Cc: netdev@vger.kernel.org
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

three gigabit ports, but some enp2611 models only have two ports
(and only one onboard PM3386.)  The current driver assumes there
are always three ports and so it doesn't work on the two-port
version of the board at all.

This patch adds a bit of logic to the enp2611 driver to limit the
number of ports to 2 if the second PM3386 isn't detected.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

On alpha:

drivers/net/dl2k.c: In function `rio_free_tx':
drivers/net/dl2k.c:768: error: `DMA_48BIT_MASK' undeclared (first use in this function)
drivers/net/dl2k.c:768: error: (Each undeclared identifier is reported only once
drivers/net/dl2k.c:768: error: for each function it appears in.)
drivers/net/dl2k.c: In function `receive_packet':
drivers/net/dl2k.c:896: error: `DMA_48BIT_MASK' undeclared (first use in this function)
drivers/net/dl2k.c: In function `rio_close':
drivers/net/dl2k.c:1803: error: `DMA_48BIT_MASK' undeclared (first use in this function)

Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Even with fiber cards ethtool reports that the connected port is TP,
the patch fix this.
Signed-off-by: NKarsten Keil <kkeil@suse.de>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

661FX7MI-S motherboard which uses the SiS 661FX chipset.  The patch adds
an entry to mii_chip_info for the transceiver.

The PHY ids were found using the sis900_c_122.diff patch from
http://brownhat.org/sis900.html but that patch didn't solve the problem,
because the PHY at address 1 was already being chosen.

Without my patch, when bursts of packets arrive from other hosts on a
LAN, the interface dropped one roughly 10% of the time, causing
retransmits.  There were fifth second pauses in refresh of large xterms,
and it made Netrek suck.  I can provide further test data.

Workaround in lieu of patch is to use mii-tool to advertise
100baseTx-HD, then force renegotiation.

I wasn't able to identify the actual transceiver, so the description
field is a guess.

This patch is similar to Artur Skawina's patch:
http://marc.theaimsgroup.com/?l=linux-netdev&m=114297516729079&w=2

I'm not sure, but I wonder if it means the default behaviour should be
changed, so as to better handle future transceivers.

Diff is against 2.6.16.13.
Signed-off-by: NJames Cameron <james.cameron@hp.com>
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Typo will be harder with this one.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

make sure phy_map entries whose PHY address is masked are initialized
to NULL, given that other code (such as mdiobus_unregister for
instance) assumes that non-NULL phy_map entries are allocated
phy_devices
Signed-off-by: NHerbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Bringing down a port also masks off the status and other IRQ's
needed for device to function due to missing paren's.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>