devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

According documentation bit ACLKRPOL is set to 0 (receiver samples data
on falling edge) and when set to 1 (receiver samples data on rising edge).

I2S data are always sampled on falling edge and valid during rising edge
of bit clock. So in case of capture data transmitter sample data on falling
edge and macsp must read then on rising edge.
Signed-off-by: NMarek Belisko <marek.belisko@streamunlimited.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The missing break here means that we always return early and the
function is a no-op.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

When McASP is bit clock and frame clock master enable pin output for rx clocks.
Signed-off-by: NMarek Belisko <marek.belisko@streamunlimited.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Update dapm_clock_event to use clk_prepare_enable and
clk_disable_unprepare.
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We get a lot of build warnings from the msp driver like:

In file included from sound/soc/ux500/ux500_msp_dai.h:21:0,
                 from sound/soc/ux500/mop500.c:25:
sound/soc/ux500/ux500_msp_i2s.h:546:11: warning: 'struct msp_i2s_platform_data' declared inside parameter list [enabled by default]
    struct msp_i2s_platform_data *platform_data);
           ^
sound/soc/ux500/ux500_msp_i2s.h:546:11: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]

The easiest solution is to add a declaration of the struct name.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

For TDM mode, BCLK-to-LCLK ratio is computed as (tdm_slots) x (word_length).
I2S mode is only subset of TDM mode with specific tdm_slots = 2 channels.
Also bclk_lrclk_ratio can be greater than 255, therefore u16 need to be used.
Signed-off-by: NMichal Bachraty <michal.bachraty@streamunlimited.com>
Acked-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

As pointed of by Vaibhav, commit message: "ASoC: davinci-mcasp: Add support for multichannel playback"
number of active serializers can be hidden into fifo_level variable, which is set in davimci-mcasp.
Signed-off-by: NMichal Bachraty <michal.bachraty@streamunlimited.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

dma_request_slave_channel() is a more appropriate API for dmaengine
clients that adopt generic DMA bindings to call.  Let's use it instead
of of_dma_request_slave_channel() to save <linux/of_dma.h> include.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The examples in Documentation/devicetree/bindings/dma/dma.txt recommends
the name for dma channel doing both RX and TX to be "rx-tx".  This
becomes a common pattern that has been adopted by platforms that
converts to generic DMA bindings.  Let's follow this common pattern in
generic-dmaengine-pcm.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Use the generic dmaengine PCM driver instead of a custom implementation.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This allows us to access the DAI DMA data when we create the PCM. We'll use
this when converting mxs to generic DMA engine PCM driver.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The MXS SAIF is only half-duplex so set the SNDRV_PCM_INFO_HALF_DUPLEX flag for
the PCM in order to prevent playback and capture from running at the same time.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Some platforms which are half-duplex share the same DMA channel between the
playback and capture stream. Add support for this to the generic dmaengine PCM
driver.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Previously we just hard coded all streams as playback streams, this
patch checks the DAI to see if it is a capture or playback stream. It is
worth noting that at this time only unidirectional streams are
supported.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The buffer passed to the copy callback should not be const because the
copy callback can be used for capture and playback.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Use the generic dmaengine PCM driver instead of a custom implemention.  There is
a minor functional change, the ux500 PCM driver did not preallocate the audio
buffer, while the generic dmaengine PCM driver will do this.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The hardware revision of the codec is based at 0x40.  Subtract that
before convering to ASCII.  The same as it is done for 98095.
Signed-off-by: NDylan Reid <dgreid@chromium.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

This patch adds a playback and capture streams to the dummy codec DAI
configuration. Most permissive set of sampling rates and formats is used.

This patch is needed for playback and capturing on a codec-less systems,
as otherwise the PCM device nodes are not even created.
Signed-off-by: NStas Sergeev <stsp@users.sourceforge.net>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Use the generic dmaengine PCM driver instead of a custom implementation.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This allows us to access the DAI DMA data when we create the PCM. We'll use
this when converting imx to generic DMA engine PCM driver.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Unfortunately there are still quite a few platforms with a dmaengine driver
which do not support reporting the number of bytes left to transfer. If we want
to support these platforms in the generic dmaengine PCM driver we have.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Tested-by: NStephen Warren <swarren@nvidia.com>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Use the generic dmaengine PCM driver instead of a custom implementation.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add support for platforms which don't use devicetree yet or have to optionally
support a non-devicetree way to request the DMA channel. The patch adds the
compat_request_channel and compat_filter_fn callbacks to the
snd_dmaengine_pcm_config struct. If the compat_request_channel is implemented it
will be used to request the DMA channel. If not dma_request_channel with
compat_filter_fn as the filter function will be used to request the channel.

The patch also exports the snd_dmaengine_pcm_request_chan() function, since
compat platforms will want to use it to request their DMA channel.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Tested-by: NStephen Warren <swarren@nvidia.com>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds a generic dmaengine PCM driver. It builds on top of the
dmaengine PCM library and adds the missing pieces like DMA channel management,
buffer management and channel configuration. It will be able to replace the
majority of the existing platform specific dmaengine based PCM drivers.
Devicetree is used to map the DMA channels to the PCM device.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Tested-by: NStephen Warren <swarren@nvidia.com>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

snd_soc_{add,remove}_platform are similar to snd_soc_register_platform and
snd_soc_unregister_platform with the difference that they won't allocate and
free the snd_soc_platform structure.

Also add snd_soc_lookup_platform which looks up a platform by the device it has
been registered for.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Tested-by: NStephen Warren <swarren@nvidia.com>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Refactor the dmaengine PCM library to allow the DMA channel to be requested
before opening a PCM substream. snd_dmaengine_pcm_open() now expects a DMA
channel instead of a filter function and filter parameter as its parameters.
snd_dmaengine_pcm_close() is updated to not release the DMA channel. This allows
a dmaengine based PCM driver to request its channels before the substream is
opened.

The patch also introduces two new functions, snd_dmaengine_pcm_open_request_chan()
and snd_dmaengine_pcm_close_release_chan(), which have the same signature and
behaviour of the old snd_dmaengine_pcm_{open,close}() and internally use the new
variants of these functions. All users of snd_dmaengine_pcm_{open,close}() are
updated to use snd_dmaengine_pcm_open_request_chan() and
snd_dmaengine_pcm_close_release_chan().
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Tested-by: NStephen Warren <swarren@nvidia.com>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add definitions for AC97 control register.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Acked-by: NTimur Tabi <timur@tabi.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Correct spelling typos in printk and comments.
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Acked-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Commit b2ca7871 (ARM: S3C24XX: make gta02.h local) already replaced
the GTA02_GPIO_* constants in neo1973-wm8753.c but forgot to remove the
inclusion of mach/gta02.h before moving the file out of mach/.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The plat/regs-iis.h and plat/regs-ac97.h files in the samsung platform
are only needed by the ASoC drivers, so they can be moved into the same
directory, as one more step towards a multiplatform build.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Firmwares may provide some firmware wide configuration regions which can
be configured by the coefficient files using the firmware ID as the
algorithm ID, include these in the algorithm list.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The idma_reg_addr_init function is used by the samsung i2s driver,
which can be a loadable module, so we have to export this function.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The second argument to the module_device_table macro must be the
name of the device id array. In the samsung i2s driver, there
was a small typo, resulting in a build error when building it
as a loadable module.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

With multiplatform kernels, we cannot use hardwired IRQ
numbers in device drivers. This changes the idma driver
to use a proper resource, like all other drivers do.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Reported-by: NRyo Tsutsui <Ryo.Tsutsui@wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

The Charge Pump needs the DSP clock to work properly, without it the
bypass to HP/LINEOUT is not working properly. This requirement is not
mentioned in the datasheet but has been confirmed by Mark Brown from
Wolfson.
Signed-off-by: NAlban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

There's already a device revision stored in the core data structure,
don't duplicate it in the CODEC driver.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

A test for CONFIG_SND_SOC_UX500_AB5500 was added in v3.5. But there
never was a corresponding Kconfig symbol so this test has always
evaluated to true. And since AB5500 support was removed in v3.5 it
appears safe to remove this test and a few lines of code.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>