The recently added parity error handling used an error code that was
already defined for a different error.  This could lead to bnx2x
firmware assert.  We need to fix this with new error codes that are
defined for parity error only.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NEddie Wai <eddie.wai@broadcom.com>
Reviewed-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RSS feature in tg3 hardware has only one rx producer ring for all
RSS rings.  NAPI vector 1 is special and handles the refilling of the
rx producer ring on behalf of all RSS rings.  There is a race condition
between these RSS NAPIs and the NAPI[1].  If NAPI[1] finishes checking
for refill and then another RSS ring empties the rx producer ring
before NAPI[1] exits NAPI, the chip will be completely out of SKBs in
the rx producer ring.

We fix this by adding a flag tp->rx_refill and rely on napi_schedule()/
napi_complete() to help synchronize it to close the race condition.

Update driver version to 3.123.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some BIOS's don't setup power management correctly (what else is
new) and don't allow use of PCI Express power control. Add a special
exception module parameter to allow working around this issue.
Based on slightly different patch by Knut Petersen.
Reported-by: NArkadiusz Miskiewicz <arekm@maven.pl>
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NCong Wang <amwang@redhat.com>

Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NCong Wang <amwang@redhat.com>

Signed-off-by: NCong Wang <amwang@redhat.com>

Acked-by: NMilan Broz <mbroz@redhat.com>
Signed-off-by: NCong Wang <amwang@redhat.com>

Signed-off-by: NCong Wang <amwang@redhat.com>

Signed-off-by: NCong Wang <amwang@redhat.com>

Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NCong Wang <amwang@redhat.com>

Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NCong Wang <amwang@redhat.com>

Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NCong Wang <amwang@redhat.com>

Signed-off-by: NCong Wang <amwang@redhat.com>

Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <amwang@redhat.com>

Signed-off-by: NCong Wang <amwang@redhat.com>

Acked-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NCong Wang <amwang@redhat.com>

Acked-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NCong Wang <amwang@redhat.com>

Acked-by: NRoland Dreier <roland@purestorage.com>
Signed-off-by: NCong Wang <amwang@redhat.com>

Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <amwang@redhat.com>

Signed-off-by: NCong Wang <amwang@redhat.com>

Signed-off-by: NCong Wang <amwang@redhat.com>

Signed-off-by: NCong Wang <amwang@redhat.com>

Signed-off-by: NCong Wang <amwang@redhat.com>

Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NCong Wang <amwang@redhat.com>

Add support for the watchdog integrated into the SMSC SCH5627 and
SCH5636 superio-s. Since the watchdog is part of the hwmon logical device
and thus shares ioports with it, the watchdog driver is integrated into the
existing hwmon drivers for these.

Note that this version of the watchdog support for sch56xx superio-s
implements the watchdog chardev interface itself, rather then relying on
the recently added watchdog core / watchdog_dev. This is done because
currently some needed functionality is missing from watchdog_dev, as soon
as this functionality is added (which is being discussed on the
linux-watchdog mailinglist), I'll convert this driver over to using
watchdog_dev.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
[guenter.roeck@ericsson.com: Added missing linux/slab.h include]
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Adds multitouch support for the Gametel Android game controller.

The multitouch events are emulated by the Gametel device. Each physical button
is configured to generate a MT event on a specific coordinate. This seems to be
the only way for us to support Android games that doesn't support HID gamepads.
It is possible to inject MT events at Android level, but this requires root on
the phone.
Signed-off-by: NAndreas Nielsen <eas@svep.se>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Reported-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes:

drivers/built-in.o: In function `qmi_wwan_bind_shared':
qmi_wwan.c:(.text+0x25b686): undefined reference to `usb_cdc_wdm_register'
make[1]: *** [.tmp_vmlinux1] Error 1
Reported-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Acked-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for TI's CPSW driver.

The three port switch gigabit ethernet subsystem provides ethernet packet
communication and can be configured as an ethernet switch. Supports
10/100/1000 Mbps.
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Signed-off-by: NSriramakrishnan A G <srk@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TI CPSW ethernet switch has a built-in address lookup engine.  This patch adds
the code necessary for programming this module.
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHeiko Schocher <hs@denx.de>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prevent race condition between commands on comm channel.
Happened while unloading the driver when switching from
event to polling mode. VF got completion on the last command
before switching to polling mode, but toggle was not changed.
After the fix - VF will not write the next command before
toggle is updated.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Liang Zheng(lzheng@redhat.com) found that in the following topo,
bonding does not send igmp report when we trigger a fail-over of bonding.

eth0--
      |-- bond0 -- br0
eth1--

modprobe bonding mode=1 miimon=100 resend_igmp=10
ifconfig bond0 up
ifenslave bond0 eth0 eth1

brctl addbr br0
ifconfig br0 192.168.100.2/24 up
brctl addif br0 bond0

Add 192.168.100.2(br0) into a multicast group, like 224.10.10.10,
then trigger a fali-over in bonding.
You can see that parameter "resend_igmp" does not work.

The reason is that when we add br0 into a multicast group,
it does not propagate multicast knowledge down to its ports.

If we choose to propagate multicast knowledge down to all ports for bridge,
then we have to track every change that is done to bridge, and keep a backup
for all ports. It is hard to track, I think.

Instead I choose to modify bonding to send igmp report for its master.

Changelog:
V2: correct comments
V3: move this check into bond_resend_igmp_join_requests()
V4: only send igmp reports if bond is enslaved to a bridge
Signed-off-by: NWeiping Pan <panweiping3@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add compatible string for MPC5125 FEC. The FEC on MPC5125 additionally
supports RMII PHY interface. Configure controller/PHY interface type
according to the optional phy-connection-type property in the ethernet
node. This property should be either "rmii" or "mii".
Signed-off-by: NVladimir Ermakov <vooon341@gmail.com>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a bug when using 'ethtool -K ethx tx off' to turn off tx ip checksum,
FCoE CRC offload should not be impacte. The skb_checksum_help() is needed
only if it's not FCoE traffic for ip checksum, regardless of ethtool toggling
the tx ip checksum on or off. Instead of using CHECKSUM_PARTIAL, we will
use CHECKSUM_UNNECESSARY as a proper indication to avoid sw ip checksum
on FCoE frames.

Ref. to original discussion thread:
http://patchwork.ozlabs.org/patch/146567/

CC: "James E.J. Bottomley" <JBottomley@parallels.com>
CC: Robert Love <robert.w.love@intel.com>
Signed-off-by: NYi Zou <yi.zou@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows us to avoid a Tx hang when SR-IOV is enabled.  This hang
can be triggered by sending small packets at a rate that was triggering Rx
missed errors from the adapter while the internal Tx switch and at least
one VF are enabled.

This was all due to the fact that under heavy stress the Rx FIFO never
drained below the flow control high water mark.  This resulted in the Tx
FIFO being head of line blocked due to the fact that it relies on the flow
control high water mark to determine when it is acceptable for the Tx to
place a packet in the Rx FIFO.

The resolution for this is to set the FCRTH value to the RXPBSIZE - 32 so
that even if the ring is almost completely full we can still place Tx
packets on the Rx ring and drop incoming Rx traffic if we do not have
sufficient space available in the Rx FIFO.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of dropping the packet, we keep the skb buffer, and return
NETDEV_TX_BUSY to let upper layer retry send. This will not cause
endless loop, because the host is taking data away from ring buffer,
and we have called the stop_queue before returning NETDEV_TX_BUSY.

The stop_queue was called in the function netvsc_send() in file 
netvsc.c, then it returns to rndis_filter_send(), which returns to
netvsc_start_xmit() in file netvsc_drv.c. So the NETDEV_TX_BUSY is
indeed returned AFTER queue is stopped.
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: NK. Y. Srinivasan <kys@microsoft.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Resolve namespace issues when FCoE or DCB is not enabled.
The issue is with certain configurations we end up with namespace
problems. A simple example:

ixgbe_main.c
 - defines func A()
 - uses func A()

ixgbe_fcoe.c
 - uses func A()

ixgbe.h
 - has prototype for func A()

For default (FCoE included) all is good.  But when it isn't the namespace
checker complains about how func A() could be static.

To resolve this, created a ixgbe_lib file to contain functions used
by DCB/FCoE and their helper functions so that they are always in
namespace whether or not DCB/FCoE is enabled.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>

Just neatening.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove an unnecessary #define and use memcpy
instead of a loop to copy an ethernet address.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>