This patch adds the initialization calls into the new 7220 HCA files,
changes the Makefile to compile and link the new files, and code to
handle send DMA.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This is part of a patch series to add support for a new HCA.  This patch
adds new fields to the header files.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch adds code to enable/disable the IBTA 1.2 heartbeat for testing
if the HCA supports it.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Newer HCAs have a HW option to write a sequence number to each receive
queue entry and avoid a separate DMA of the tail register to memory.
This patch adds support for these changes.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Subnet manager SetPortinfo messages distingush between changing the link
state (DOWN, ARM, ACTIVE) and the link physical state (POLL, SLEEP,
DISABLED).  These are somewhat independent commands and affect when link
width and speed changes take effect.  Without this patch, a link DOWN
physical state NOP command was causing the link width and speed settings
to take effect which should only happen when the link physical state is
goes down (either by a SMP or some link physical error like link errors
exceeding the threshold).
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The IBA7220 uses a count-based triggering mechanism, and therefore
can't use the same bandwidth verification mechanism as older chips.

To support the 7220, allow enabling and disabling armlaunch errors on
application request.  Minor robustness improvements as well.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This adds the new (sometimes empty) chip-specific functions to the older
chips, and makes the initialization and related functions consistent across
all 3 chips.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Various hardware counters are exported via the ipath file system (since
it is binary data).  The old file format was very dependent on the HW
offsets for these registers.  Newer HCA chips can have different
counters at different offsets.  This patch adds a level of indirection
to make the file format consistent across HCAs.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

A couple of chip bugs in the iba6110 and in the iba6120 are not in more
recent chips.  This first bug swaps two of the pioavail register
locations.  In the second bug, the chip can sometimes forget to dma the
pio avail register to memory.  We indicate the presence of these bugs
with runtime flags and we indicate the presence of the flags by bumping
the SWMINOR.
Signed-off-by: NArthur Jones <arthur.jones@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The fastrcvint code's purpose was to avoid reading the interrupt
status if kernel packets were in the receive queue (to reduce
overhead).  Because intstatus was not read, we could miss the error
interrupt bit indicating freeze mode, since it only delivers a single
interrupt, even if still pending after intclear is written.

This patch removes that unsafe optimization.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix ipath_poll and enhance it so we can poll for urgent packets or
regular packets and receive notifications of when a header queue
overflows.
Signed-off-by: NRobert Walsh <robert.walsh@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

During compliance testing and when debugging some interconnect issues,
it is very useful to be able to send malformed packets, without having
the device signal them as malformed (drop, or terminate with EBP). The
hardware supports this, but the driver "diagnostic packet" interface
did not.

Extend capability to send specific malformed packets for testing.
Signed-off-by: NMichael Albaugh <Michael.Albaugh@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The IPATH_RUNTIME_PBC_REWRITE and the IPATH_RUNTIME_LOOSE_DMA_ALIGN
flags were not ever implemented correctly and did not turn out to be
necessary.  Remove the last vestiges of these flags but mark the spot
with a comment to remind us to not reuse these flags in the interest
of binary compatibility.  The INFINIPATH_XGXS_SUPPRESS_ARMLAUNCH_ERR
bit was also not found to be useful, so it was dropped in the cleanup
as well.
Signed-off-by: NJohn Gregor <john.gregor@qlogic.com>
Signed-off-by: NArthur Jones <arthur.jones@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Due to a chip bug, the PIOAvail register is not always updated to
memory.  This patch allows userspace to force an update.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Improve port-sharing performance by allowing any process to receive
packets from the shared hardware port under a spin lock for mutual
exclusion. Previously, one process was nominated as the master and
that process was responsible for receiving all packets from the shared
hardware port and either consuming them or forwarding them to their
destination. This led to starvation problems for other processes when
the master process was busy in computation phases.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This is a sticky state.  It is useful for diagnosing problems with
boards versus cable/switch problems.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This change moves around port assignment so that it happens before any
memory is allocated.  This allows memory to be allocated on an appropriate
CPU, which improves performance for users of /dev/ipath.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

We can sometimes trigger parity errors due to processor speculative
reads to our write-combined memory (mostly seen on Woodcrest).   Add a
stats counter for these.

Factored out the sendbuffererror buffer cancellation code so it can be
used in the new handling; suppress likely subsequent error messages if
within two jiffies of the cancellation.

Also restore 2 dropped TXE lines on hwe_bitsextant noticed while
debugging.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This also entailed a little GPIO-interrupt general cleanup.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This allows multiple userspace processes to share a single hardware
context in a master/slave arrangement.  It is backwards binary compatible
with existing userspace.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

When we first submitted a userspace subnet management agent, it was
rejected, so we left it out of the final driver submission.  This patch
removes a number of vestigial references to it.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Remove ips namespace from infinipath drivers.  This renames ips_common.h to
ipath_common.h.  Definitions, data structures, etc.  that were not used by
kernel modules have moved to user-only headers.  All names including ips have
been renamed to ipath.  Some names have had an ipath prefix added.
Signed-off-by: NChristian Bell <christian.bell@qlogic.com>
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

We do a few more explicit checks for specific models, and now also support the
old PathScale serial number style, or new QLogic style.

This is backwards compatible with previous versions of software and hardware.
That is, older software will see a plausible serial number and correct GUID
when used with a new board, while newer software will correctly handle an
older board.
Signed-off-by: NMike Albaugh <mike.albaugh@qlogic.com>
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The two arrays only had space for 4 units.

Also changed from ipath_set_sps_lid() to ipath_set_lid(); the sps was
leftover.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Also count the number of interrupts where that works (fastrcvint).  On any
interrupt where the port0 head and tail registers are not equal, just call the
ipath_kreceive code without reading the interrupt status, thus saving the
approximately 0.25usec processor stall waiting for the read to return.  If any
other interrupt bits are set, or head==tail, take the normal path, but that
has been reordered to handle read ahead of pioavail.  Also no longer call
ipath_kreceive() from ipath_qcheck(), because that just seems to make things
worse, and isn't really buying us anything, these days.

Also no longer loop in ipath_kreceive(); better to not hold things off too
long (I saw many cases where we would loop 4-8 times, and handle thousands (up
to 3500) in a single call).
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Made in-memory rcvhdrq tail update be in dma_alloc'ed memory, not random user
or special kernel (needed for ppc, also "just the right thing to do").

Some cleanups to make unexpected link transitions less likely to produce
complaints about packet errors, and also to not leave SMA packets stuck and
unable to go out.

A few other random debug and comment cleanups.

Always init rcvhdrq head/tail registers to 0, to avoid race conditions (should
have been that way some time ago).
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

ipath_common.h and ips_common.h contain definitions shared between
userspace and the kernel.

ipath_kernel.h is the core driver header file.

ipath_debug.h contains mask values used for controlling driver debugging.

ipath_registers.h contains bitmask definitions used in chip registers.
Signed-off-by: NBryan O'Sullivan <bos@pathscale.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>