Enables flow control to be set in SerDes autoneg mode. This is what is
done for copper, but relies on a different set of register/bit checks
since this is all done within the Mac registers.

Remove inapplicable comment in defines.h
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

perm_addr is initialized correctly in register_netdevice() so to init it in
drivers is no longer needed.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers.  This patch fixes all of
them back up to be properly aligned.

Bonus is that this almost removes 100 lines of code, always a nice
surprise.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Cc: Alex Duyck <alexander.h.duyck@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Tushar Dave <tushar.n.dave@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Update comments to conform to the preferred style for networking code as
described in ./Documentation/CodingStyle and checked for in the recently
added checkpatch NETWORKING_BLOCK_COMMENT_STYLE test.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This is a HW requirement. Although a buffer as short as 1 byte is allowed,
the total length of packet before, padding and CRC insertion, must be at
least 17 bytes.  So pad all small packets manually up to 17 bytes before
delivering them to HW.
Signed-off-by: NTushar Dave <tushar.n.dave@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch originated from Hiroaki SHIMODA but has been modified
by Intel with some minor cleanups and additional commit log text.

Denys Fedoryshchenko and others reported Tx stalls on e1000e with
BQL enabled.  Issue was root caused to hardware delays. They were
introduced because some of the e1000e hardware with transmit
writeback bursting enabled, waits until the driver does an
explict flush OR there are WTHRESH descriptors to write back.

Sometimes the delays in question were on the order of seconds,
causing visible lag for ssh sessions and unacceptable tx
completion latency, especially for BQL enabled kernels.

To avoid possible Tx stalls, change WTHRESH back to 1.

The current plan is to investigate a method for re-enabling
WTHRESH while not harming BQL, but those patches will be later
for net-next if they work.

please enqueue for stable since v3.3 as this bug was introduced in
commit 3f0cfa3b
Author: Tom Herbert <therbert@google.com>
Date:   Mon Nov 28 16:33:16 2011 +0000

    e1000e: Support for byte queue limits

    Changes to e1000e to use byte queue limits.
Reported-by: NDenys Fedoryshchenko <denys@visp.net.lb>
Tested-by: NDenys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: NHiroaki SHIMODA <shimoda.hiroaki@gmail.com>
CC: eric.dumazet@gmail.com
CC: therbert@google.com
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

i218 is the next-generation LOM that will be available on systems with the
Lynx Point LP Platform Controller Hub (PCH) chipset from Intel.  This patch
provides the initial support of those devices.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Early Receive has been disabled in the driver so this comment is no longer
applicable.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

CHECK: multiple assignments should be avoided
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add comments to memory barriers per strict checkpatch.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The POEMB register is 32 bits, not 16.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

With a low enough MSS on the link partner and TSO enabled locally, the
networking stack can periodically send a very large (e.g.  64KB) TCP
message for which the driver will attempt to use more Tx descriptors than
are available by default in the Tx ring.  This is due to a workaround in
the code that imposes a limit of only 4 MSS-sized segments per descriptor
which appears to be a carry-over from the older e1000 driver and may be
applicable only to some older PCI or PCIx parts which are not supported in
e1000e.  When the driver gets a message that is too large to fit across the
configured number of Tx descriptors, it stops the upper stack from queueing
any more and gets stuck in this state.  After a timeout, the upper stack
assumes the adapter is hung and calls the driver to reset it.

Remove the unnecessary limitation of using up to only 4 MSS-sized segments
per Tx descriptor, and put in a hard failure test to catch when attempting
to check for message sizes larger than would fit in the whole Tx ring.
Refactor the remaining logic that limits the size of data per Tx descriptor
from a seemingly arbitrary 8KB to a limit based on the dynamic size of the
Tx packet buffer as described in the hardware specification.

Also, fix the logic in the check for space in the Tx ring for the next
largest possible packet after the current one has been successfully queued
for transmit, and use the appropriate defines for default ring sizes in
e1000_probe instead of magic values.

This issue goes back to the introduction of e1000e in 2.6.24 when it was
split off from e1000.
Reported-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Cc: Stable <stable@vger.kernel.org> [2.6.24+]
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use PCI Express Capability access functions to simplify e1000e driver.

[bhelgaas: split e1000e and igb into separate patches]
Signed-off-by: NJiang Liu <jiang.liu@huawei.com>
Signed-off-by: NYijing Wang <wangyijing@huawei.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some users report issues with link failing when connected to certain
switches.  This gives the user the ability to control the MDI state
from the driver, allowing users to work around some improperly
behaving switches.

Forcing in this driver is for now only allowed when auto-neg is
enabled.

This is in regards to the related ethtool app patch and
bugzilla.kernel.org bug 11998
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
CC: bruce.w.allan@intel.com
CC: n.poppelier@xs4all.nl
CC: bastien@durel.org
CC: jsveiga@it.eng.br
Tested-by: Aaron Brown aaron.f.brown@intel.com
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In order for e1000e to support MDI setting support via
ethtool this code is needed to allow setting the MDI state
via software.

This is in regards to the related ethtool patch and
fixes bugzilla.kernel.org bug 11998
Signed-off-by: NBruce W Allan <bruce.w.allan@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown aaron.f.brown@intel.com
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch resolves a "BUG: unable to handle kernel paging request at ..."
oops while dumping packet data. The issue occurs with IOMMU enabled due to
the address provided by phys_to_virt().

This patch avoids phys_to_virt() by using skb->data and the address of the
pages allocated for Rx.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>

A bus trace shows that while executing e1000e_down, TCTL is cleared except
for the PSP bit.  This occurs while in the middle of fetching a TSO packet
since the Tx packet buffer is full at that point. Before the device is
reset, the e1000_watchdog_task starts to run from the middle (it was
apparently pre-empted earlier, although that is not in the trace) and sets
TCTL.EN.  At that point, 82571 transmits the corrupted packet, apparently
because TCTL.MULR was cleared in the middle of fetching a packet, which is
forbidden.

Driver should just clear TCTL.EN in e1000_reset_hw_82571 instead of
clearing the entire register, so as not to change any settings in the
middle of fetching a packet.
Signed-off-by: NTushar Dave <tushar.n.dave@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>

Found that commit d478eb44 was a bad commit.
If the link partner is transmitting codeword (even if NULL codeword),
then the RXCW.C bit will be set so check for RXCW.CW is unnecessary.
Ref: RH BZ 840642
Reported-by: NFabio Futigami <ffutigam@redhat.com>
Signed-off-by: NTushar Dave <tushar.n.dave@intel.com>
CC: Marcelo Ricardo Leitner <mleitner@redhat.com>
CC: stable <stable@vger.kernel.org> [2.6.38+]
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>

This driver now offers software transmit time stamping, so it should
advertise that fact via ethtool. Compile tested only.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>

Cc: Willem de Bruijn <willemb@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When configuring interrupt throttling on 82574 in MSI-X mode, we need to
be programming the EITR registers instead of the ITR register.

-rc2: Renamed e1000_write_itr() to e1000e_write_itr(), fixed whitespace
      issues, and removed unnecessary !! operation.
-rc3: Reduced the scope of the loop variable in e1000e_write_itr().
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Acked-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Cleanup code to make it more clean and readable.
Signed-off-by: NTushar Dave <tushar.n.dave@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Occasionally, the PHY can be initially inaccessible when the first read of
a PHY register, e.g. PHY_ID1, happens (signified by the returned value
0xFFFF) but subsequent accesses of the PHY work as expected.  Add a retry
counter similar to how it is done in the generic e1000_get_phy_id().

Also, when the PHY is completely inaccessible (i.e. when subsequent reads
of the PHY_IDx registers returns all F's) and the MDIO access mode must be
set to slow before attempting to read the PHY ID again, the functions that
do these latter two actions expect the SW/FW/HW semaphore is not already
set so the semaphore must be released before and re-acquired after calling
them otherwise there is an unnecessarily inordinate amount of delay during
device initialization.
Reported-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

SYNCH bit and IV bit of RXCW register are sticky. Before examining these bits,
RXCW should be read twice to filter out one-time false events and have correct
values for these bits. Incorrect values of these bits in link check logic can
cause weird link stability issues if auto-negotiation fails.

CC: stable <stable@vger.kernel.org> [2.6.38+]
Reported-by: NDean Nelson <dnelson@redhat.com>
Signed-off-by: NTushar Dave <tushar.n.dave@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix incorrect start markers, wrapped summary lines, missing section
breaks, incorrect separators, and some name mismatches.  Delete
a few that are content-free.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently only used when packet split mode is enabled with jumbo frames,
IP payload checksum (for fragmented UDP packets) is mutually exclusive with
receive hashing offload since the hardware uses the same space in the
receive descriptor for the hardware-provided packet checksum and the RSS
hash, respectively.  Users currently must disable jumbos when receive
hashing offload is enabled, or vice versa, because of this incompatibility.
Since testing has shown that IP payload checksum does not provide any real
benefit, just remove it so that there is no longer a choice between jumbos
or receive hashing offload but not both as done in other Intel GbE drivers
(e.g. e1000, igb).

Also, add a missing check for IP checksum error reported by the hardware;
let the stack verify the checksum when this happens.

CC: stable <stable@vger.kernel.org> [3.4]
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on a report from Ethan Zhao, before calling register_netdev() the
driver should be using logging macros that do not display the potentially
confusing "(unregistered net_device)" yet still display the useful driver
name and PCI bus/device/function.
Reported-by: NEthan Zhao <ethan.kernel@gmail.com>
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

commit 44abd5c1 introduced NULL pointer
dereferences when attempting to access the check_reset_block function
pointer on 8257x and 80003es2lan non-copper devices.

This fix should be applied back through 3.4.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The definition of I217_PROXY_CTRL must use the BM_PHY_REG() macro instead
of the PHY_REG() macro for PHY page 800 register 70 since it is for a PHY
register greater than the maximum allowed by the latter macro, and fix a
typo setting the I217_MEMPWR register in e1000_suspend_workarounds_ich8lan.

Also for clarity, rename a few defines as bit definitions instead of masks.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This define is needed by i217.
Reported-by: NBjorn Mork <bjorn@mork.no>
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

During merge of net to net-next the changes in patch:

e1000e: Fix default interrupt throttle rate not set in NIC HW

got munged in param.c of the e1000e driver.  This rectifies the
merge issues.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During merge of net to net-next the changes in patch:

e1000e: Fix default interrupt throttle rate not set in NIC HW

got munged in param.c of the e1000e driver.  This rectifies the
merge issues.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Clear the REQ and GNT bit in the eeprom control register (EECD).
This is required if the eeprom is to be accessed with auto read
EERD register.

After a cold reset this doesn't matter but if PBIST MAC test was
executed before booting, the register was left in a dirty state
(the 2 bits where set), which caused the read operation to time out
and returning 0.

Reference (page 312):
http://download.intel.com/design/network/manuals/316080.pdfReported-by: NAleksandar Igic <aleksandar.igic@dektech.com.au>
Signed-off-by: NRichard Alpe <richard.alpe@ericsson.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Like other supported (igp) PHYs, the driver needs to be able to force the
master/slave mode on 82577.  Since the code is the same as what already
exists in the code flow for igp PHYs, move it to a new function to be
called for both flows.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

i217 is the next-generation LOM that will be available on systems with the
Lynx Point Platform Controller Hub (PCH) chipset from Intel.  This patch
provides the initial support for the device.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Version bump to 1.11.3-k.
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>