Signed-off-by: NDenis Kenzior <denkenz@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NDenis Kenzior <denkenz@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NDenis Kenzior <denkenz@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This commit implements the TX side of NL80211_CMD_CONTROL_PORT_FRAME.
Userspace provides the raw EAPoL frame using NL80211_ATTR_FRAME.
Userspace should also provide the destination address and the protocol
type to use when sending the frame.  This is used to implement TX of
Pre-authentication frames.  If CONTROL_PORT_ETHERTYPE_NO_ENCRYPT is
specified, then the driver will be asked not to encrypt the outgoing
frame.

A new EXT_FEATURE flag is introduced so that nl80211 code can check
whether a given wiphy has capability to pass EAPoL frames over nl80211.
Signed-off-by: NDenis Kenzior <denkenz@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This commit also adds cfg80211_rx_control_port function.  This is used
to generate a CMD_CONTROL_PORT_FRAME event out to userspace.  The
conn_owner_nlportid is used as the unicast destination.  This means that
userspace must specify NL80211_ATTR_SOCKET_OWNER flag if control port
over nl80211 routing is requested in NL80211_CMD_CONNECT,
NL80211_CMD_ASSOCIATE, NL80211_CMD_START_AP or IBSS/mesh join.
Signed-off-by: NDenis Kenzior <denkenz@gmail.com>
[johannes: fix return value of cfg80211_rx_control_port()]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

We already have 'ifmgd' here, and it's already assigned
to the same value, so remove the duplicate.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In the current implementation, mac80211 advertises the support of
AP_VLANs based on the driver's support for AP mode; it also
blocks encrypted AP_VLAN operation on devices advertising
SW_CRYPTO_CONTROL.

The implementation seems weird in it's current form and could be
often confusing, this is because there can be drivers advertising
both SW_CRYPTO_CONTROL and AP mode support (ex: ath10k) in which case
AP_VLAN will still be supported but only in open BSS and not in
secured BSS.

When SW_CRYPTO_CONTROL is enabled, it makes more sense if the decision
to support AP_VLANs is left to the driver. Mac80211 can then allow
AP_VLAN operations depending on the driver support.
Signed-off-by: NManikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In general regulatory self managed devices maintain their own
regulatory profiles thus it doesn't have to query the regulatory database
on country change.

ETSI has recently introduced a new channel access mechanism for 5GHz
that all wlan devices need to comply with.
These values are stored in the regulatory database.
There are self managed devices which can't maintain these
values on their own. Add API to allow self managed regulatory devices
to query the regulatory database for high band wmm rule.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
[johannes: fix documentation]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

ETSI has recently added new requirements that restrict the WMM
parameter values for 5GHz frequencies.  We need to take care of the
following scenarios in order to comply with these new requirements:

1. When using mac80211 default values;
2. When the userspace tries to configure its own values;
3. When associating to an AP which advertises WWM IE.

When associating to an AP, the client uses the values in the
advertised WMM IE.  But the AP may not comply with the new ETSI
requirements, so the client needs to check the current regulatory
rules and use those limits accordingly.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The whole code is set up to allow RCU reads of this data, but
then uses rtnl_dereference() which requires the RTNL. Convert
it to rcu_dereference_rtnl() which makes it require only RCU
or the RTNL, to allow RCU-protected reading of the data.
Reviewed-by: NCoelho, Luciano <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

ETSI EN 301 893 v2.1.1 (2017-05) standard defines a new channel access
mechanism that all devices (WLAN and LAA) need to comply with.
The regulatory database can now be loaded into the kernel and also
has the option to load optional data.
In order to be able to comply with ETSI standard, we add wmm_rule into
regulatory rule and add the option to read its value from the regulatory
database.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
[johannes: fix memory leak in error path]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NDenis Kenzior <denkenz@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NDenis Kenzior <denkenz@gmail.com>
[johannes: fix race with wdev lock/unlock by just acquiring once]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NDenis Kenzior <denkenz@gmail.com>
[johannes: fix race with wdev lock/unlock by just acquiring once]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently autodisconnect_wk assumes that only interface types of
P2P_CLIENT and STATION use conn_owner_nlportid.  Change this so all
interface types are supported.
Signed-off-by: NDenis Kenzior <denkenz@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently channel switch/start_ap to DFS channel cannot be done to
non-CAC-cleared channel even if DFS offload if enabled.
Make non-cleared DFS channels available if DFS offload is enabled.
CAC will be started by HW after channel change, start_ap call, etc.
Signed-off-by: NDmitry Lebed <dlebed@quantenna.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Exclude CAC_STARTED event from !wdev->cac_started check,
since cac_started will be set later in the same function.
Signed-off-by: NDmitry Lebed <dlebed@quantenna.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Bandwidth change value reported via nl80211 contains mac80211
specific enum value(ieee80211_sta_rx_bw) and which is not
understand by userspace application. Map the mac80211 specific
value to nl80211_chan_width enum value to avoid using wrong value
in the userspace application. And used station's ht/vht capability
to map IEEE80211_STA_RX_BW_20 and IEEE80211_STA_RX_BW_160 with
proper nl80211 value.
Signed-off-by: NTamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

SMPS_MODE change value notified via nl80211 contains mac80211
specific value(ieee80211_smps_mode) and user space application
will not know those values. This patch add support to map
the mac80211 enum value to nl80211_smps_mode which will be
understood by the userspace application.
Signed-off-by: NTamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

With drivers implementing rate control in driver or firmware
rate_control_send_low() may not get called, and thus the
driver needs to know about changes in the multicast rate.

Add and use a new BSS change flag for this.
Signed-off-by: NPradeep Kumar Chitrapu <pradeepc@codeaurora.org>
[rewrite commit message]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add wiphy EXT_FEATURE flag to indicate that HW or driver does
all DFS actions by itself.
User-space functionality already implemented in hostapd using
vendor-specific (QCA) OUI to advertise DFS offload support.
Need to introduce generic flag to inform about DFS offload support.
For devices with DFS_OFFLOAD flag set user-space will no longer
need to issue CAC or do any actions in response to
"radar detected" events. HW will do everything by itself and send
events to user-space to indicate that CAC was started/finished, etc.
Signed-off-by: NDmitrii Lebed <dlebed@quantenna.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

CAC_STARTED event is needed for DFS offload feature and
should be generated by driver/HW if DFS_OFFLOAD is enabled.
Signed-off-by: NDmitry Lebed <dlebed@quantenna.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When the low-level driver returns an invalid RSSI indication,
set the signal value to 0 as an indication to the upper layer.

Also, skip average level computation if signal is invalid.
Signed-off-by: NJean Pierre TOSONI <jp.tosoni@acksys.fr>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

use proc_remove_subtree() for subtree removal, both on setup failure
halfway through and on teardown.  No need to make simple things
complex...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rds_tcp_connection allocation/free management has the potential to be
called from __rds_conn_create after IRQs have been disabled, so
spin_[un]lock_bh cannot be used with rds_tcp_conn_lock.

Bottom-halves that need to synchronize for critical sections protected
by rds_tcp_conn_lock should instead use rds_destroy_pending() correctly.

Reported-by: syzbot+c68e51bb5e699d3f8d91@syzkaller.appspotmail.com
Fixes: ebeeb1ad ("rds: tcp: use rds_destroy_pending() to synchronize
       netns/module teardown and rds connection/workq management")
Signed-off-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We rename some lists and fields in struct publication both to make
the naming more consistent and to better reflect their roles. We
also update the descriptions of those lists.

node_list -> local_publ
cluster_list -> all_publ
pport_list -> binding_sock
ref -> port

There are no functional changes in this commit.
Acked-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The size of struct publication can be reduced further. Membership in
lists 'nodesub_list' and 'local_list' is mutually exlusive, in that
remote publications use the former and local publications the latter.
We replace the two lists with one single, named 'binding_node' which
reflects what it really is.
Acked-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As a further consequence of the previous commits, we can also remove
the member 'zone_list 'in struct name_info and struct publication.
Instead, we now let the member cluster_list take over the role a
container of all publications of a given <type,lower, upper>.
We also remove the counters for the size of those lists, since
they don't serve any purpose.
Acked-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As a consequence of the previous commit we nan now eliminate zone scope
related lists in the name table. We start with name_table::publ_list[3],
which can now be replaced with two lists, one for node scope publications
and one for cluster scope publications.
Acked-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Publications for TIPC_CLUSTER_SCOPE and TIPC_ZONE_SCOPE are in all
aspects handled the same way, both on the publishing node and on the
receiving nodes.

Despite previous ambitions to the contrary, this is never going to change,
so we take the conseqeunce of this and obsolete TIPC_ZONE_SCOPE and related
macros/functions. Whenever a user is doing a bind() or a sendmsg() attempt
using ZONE_SCOPE we translate this internally to CLUSTER_SCOPE, while we
remain compatible with users and remote nodes still using ZONE_SCOPE.

Furthermore, the non-formalized scope value 0 has always been permitted
for use during lookup, with the same meaning as ZONE_SCOPE/CLUSTER_SCOPE.
We now permit it even as binding scope, but for compatibility reasons we
choose to not change the value of TIPC_CLUSTER_SCOPE.
Acked-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These pernet_operations register and unregister ipvs app.
register_ip_vs_app(), unregister_ip_vs_app() and
register_ip_vs_app_inc() modify per-net structures,
and there are no global structures touched. So,
this looks safe to be marked as async.
Signed-off-by: NKirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Exit method stops two per-net threads and cancels
delayed work. Everything looks nicely per-net divided.
Signed-off-by: NKirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These pernet_operations register and unregister nf hooks,
/proc entries, sysctl, percpu statistics. There are several
global lists, and the only list modified without exclusive
locks is ip_vs_conn_tab in ip_vs_conn_flush(). We iterate
the list and force the timers expire at the moment. Since
there were possible several timer expirations before this
patch, and since they are safe, the patch does not invent
new parallelism of their destruction. These pernet_operations
look safe to be converted.
Signed-off-by: NKirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These pernet_operations initialize and destroy net_generic()
data pointed by ovs_net_id. Exit method destroys vports from
alive net to exiting net. Since they are only pernet_operations
interested in this data, and exit method is executed under
exclusive global lock (ovs_mutex), they are safe to be executed
in parallel.
Signed-off-by: NKirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These pernet_operations register and unregister sysctl table.
Exit methods frees platform_labels from net::mpls::platform_label.
Everything is per-net, and they looks safe to be marked async.
Signed-off-by: NKirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Init method is rather simple. Exit method queues del_work
for every tunnel from per-net list. This seems to be safe
to be marked async.
Signed-off-by: NKirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: NGuillaume Nault <g.nault@alphalink.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set tp->snd_ssthresh to BDP upon STARTUP exit. This allows us
to check if a BBR flow exited STARTUP and the BDP at the
time of STARTUP exit with SCM_TIMESTAMPING_OPT_STATS. Since BBR does not
use snd_ssthresh this fix has no impact on BBR's behavior.
Signed-off-by: NYousuk Seung <ysseung@google.com>
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NPriyaranjan Jha <priyarjha@google.com>
Signed-off-by: NSoheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds TCP_NLA_SND_SSTHRESH stat into SCM_TIMESTAMPING_OPT_STATS
that reports tcp_sock.snd_ssthresh.
Signed-off-by: NYousuk Seung <ysseung@google.com>
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NPriyaranjan Jha <priyarjha@google.com>
Signed-off-by: NSoheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Reviewed-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ipv6 support to the smc socket layer functions. Make use of the
updated clc layer functions to retrieve and match ipv6 information.
The indicator for ipv4 or ipv6 is the protocol constant that is provided
in the socket() call with address family AF_SMC.
Based-on-patch-by: NTakanori Ueda <tkueda@jp.ibm.com>
Signed-off-by: NKarsten Graul <kgraul@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CLC layer is updated to support ipv6 proposal messages from peers and
to match incoming proposal messages against the ipv6 addresses of the net
device. struct smc_clc_ipv6_prefix is updated to provide the space for an
ipv6 address (struct was not used before). SMC_CLC_MAX_LEN is updated to
include the size of the proposal prefix. Existing code in net is not
affected, the previous SMC_CLC_MAX_LEN value is large enough to hold ipv4
proposal messages.
Signed-off-by: NKarsten Graul <kgraul@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>