in_dev_find() need a namespace to pass it to fib_get_table(), so add
an argument.
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By default, the responder_resources parameter is set to that received
in a connection request.  The passive side may override this value
when accepting the connection.  Use the value provided by the passive
side when transitioning the QP to RTR state, rather than the value
given in the connect request.  Without this change, the RTR transition
may fail if the passive side supports fewer responder_resources than
that in the request.

For code consistency and to protect against QP destruction, restructure
overriding initiator_depth to match how responder_resources is set.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

An IPoIB subnet on an IB fabric that spans multiple IB subnets can't
use link-local scope in multicast GIDs.  The existing routines that
map IP/IPv6 multicast addresses into IB link-level addresses hard-code
the scope to link-local, and they also leave the partition key field
uninitialised.  This patch adds a parameter (the link-level broadcast
address) to the mapping routines, allowing them to initialise both the
scope and the P_Key appropriately, and fixes up the call sites.

The next step will be to add a way to configure the scope for an IPoIB
interface.
Signed-off-by: NRolf Manderscheid <rvm@obsidianresearch.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Enable conn_id remove on the passive side after connection
establishment.  This corrects an issue where the IB driver can't be
unloaded after running applications over RDS.  The 'dev_remove' counter
does not reach 0 for established connections on the passive side.

This problem is limited to device removal, and only occurs on the
passive side if there are established connections.
Signed-off-by: NVladimir Sokolovsky <vlad@mellanox.co.il>
Reviewed-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Set the initiator depth and responder resources to the device max
values for new connect request events in the iWARP connection manager.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

  There is a justifying patch for Stephen's patches. Stephen's patches
disallows using a port range of one single port and brakes the meaning
of the 'remaining' variable, in some places it has different meaning.
My patch gives back the sense of 'remaining' variable. It should mean
how many ports are remaining and nothing else. Also my patch allows
using a single port.

  I sure we must be able to use mentioned port range, this does not
restricted by documentation and does not brake current behavior.

usefull links:
Patches posted by Stephen Hemminger
  http://marc.info/?l=linux-netdev&m=119206106218187&w=2
  http://marc.info/?l=linux-netdev&m=119206109918235&w=2

Andrew Morton's comment
  http://marc.info/?l=linux-kernel&m=119248225007737&w=2

1. Allows using a port range of one single port.
2. Gives back sense of 'remaining' variable.
Signed-off-by: NAnton Arapov <aarapov@redhat.com>
Acked-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Deadlock condition reported by Kanoj Sarcar <kanoj@netxen.com>.
The deadlock occurs when a connection request arrives at the same
time that a wildcard listen is being destroyed.

A wildcard listen maintains per device listen requests for each
RDMA device in the system.  The per device listens are automatically
added and removed when RDMA devices are inserted or removed from
the system.

When a wildcard listen is destroyed, rdma_destroy_id() acquires
the rdma_cm's device mutex ('lock') to protect against hot-plug
events adding or removing per device listens.  It then tries to
destroy the per device listens by calling ib_destroy_cm_id() or
iw_destroy_cm_id().  It does this while holding the device mutex.

However, if the underlying iw/ib CM reports a connection request
while this is occurring, the rdma_cm callback function will try
to acquire the same device mutex.  Since we're in a callback,
the ib_destroy_cm_id() or iw_destroy_cm_id() calls will block until
their callback thread returns, but the callback is blocked waiting for
the device mutex.

Fix this by re-working how per device listens are destroyed.  Use
rdma_destroy_id(), which avoids the deadlock, in place of
cma_destroy_listen().  Additional synchronization is added to handle
device hot-plug events and ensure that the id is not destroyed twice.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

If a user allocates a QP on an rdma_cm_id, the rdma_cm will automatically
transition the QP through its states (RTR, RTS, error, etc.)  While the
QP state transitions are occurring, the QP itself must remain valid.
Provide locking around the QP pointer to prevent its destruction while
accessing the pointer.

This fixes an issue reported by Olaf Kirch from Oracle that resulted in
a system crash:

"An incoming connection arrives and we decide to tear down the nascent
 connection.  The remote ends decides to do the same.  We start to shut
 down the connection, and call rdma_destroy_qp on our cm_id. ... Now
 apparently a 'connect reject' message comes in from the other host,
 and cma_ib_handler() is called with an event of IB_CM_REJ_RECEIVED.
 It calls cma_modify_qp_err, which for some odd reason tries to modify
 the exact same QP we just destroyed."
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Expansion of original idea from Denis V. Lunev <den@openvz.org>

Add robustness and locking to the local_port_range sysctl.
1. Enforce that low < high when setting.
2. Use seqlock to ensure atomic update.

The locking might seem like overkill, but there are
cases where sysadmin might want to change value in the
middle of a DoS attack.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Automatically queue MRA message to decrease the number of retries sent
by the remote side during connection establishment.  This also has the
effect of increasing the overall connection timeout without using a
longer retry time in the case of dropped packets.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Provide support to specify a type of service for a communication
identifier.  A new function call is used when dealing with IPv4
addresses.  For IPv6 addresses, the ToS is specified through the
traffic class field in the sockaddr_in6 structure.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>

[ The comments Eitan Zahavi and myself have made over the v1 post at 
  <http://lists.openfabrics.org/pipermail/general/2007-August/039247.html>
  were fully addressed. ]
 
Reviewed-by: Or Gerlitz <ogerlitz@voltaire.com> 
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Local write permission makes no sense as part of the QP access flags,
since the access flags only control what the remote end of the
connection is allowed to do.  Remove the code in the RDMA CM that
initializes qp_access_flags with IB_ACCESS_LOCAL_WRITE.
Signed-off-by: NDotan Barak <dotanb@mellanox.co.il>
Acked-by: NSean Hefty <sean.hefty@intel.com>
Acked-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The IB CM should include the HCA ACK delay when calculating the local
ACK timeout value to use for RC QPs.  If the HCA ACK delay is large
enough relative to the packet life time, then if it is not taken into
account, the calculated timeout value ends up being too small, which
can result in "retry exceeded" errors.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

next_port should be between sysctl_local_port_range[0] and [1].
However, it is initially set to a random value with get_random_bytes().  
If the value is negative when treated as a signed integer, next_port
can end up outside the expected range because of the result of the % 
operator being negative.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Several checks in the rdma_cm check against the state of the
cm_id, but only to validate that the cm_id is bound to an underlying
transport specific CM and an RDMA device.  Make the check explicit
in what we're trying to check for, since we're not synchronizing
against the cm_id state.

This will allow a user to disconnect a cm_id or reject a connection
after receiving a device removal event.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The cma_iw_handler needs to validate the state of the rdma_cm_id before
processing a new connection request to ensure that a device removal is
not already being processed for the same rdma_cm_id.  Without the state
check, the user can receive simultaneous callbacks for the same cm_id, or
a callback after they've destroyed the cm_id.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add a new routine and rename another to encapsulate common code for
synchronizing with device removal.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The struct rdma_bind_list fields for hlist are not being initialized,
resulting in a corrupted list.  Fix this by using kzalloc() to make
sure all pointers are NULL.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The rdma_cm requires that path records be reversible.  Set the
reversible bit when issuing an path record query.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Extend rdma_cm to support multicast communication.  Multicast support
is added to the existing RDMA_PS_UDP port space, as well as a new
RDMA_PS_IPOIB port space.  The latter port space allows joining the
multicast groups used by IPoIB, which enables offloading IPoIB traffic
to a separate QP.  The port space determines the signature used in the
MGID when joining the group.  The newly added RDMA_PS_IPOIB also
allows for unicast operations, similar to RDMA_PS_UDP.

Supporting the RDMA_PS_IPOIB requires changing how UD QPs are initialized,
since we can no longer assume that the qkey is constant.  This requires
saving the Q_Key to use when attaching to a device, so that it is
available when creating the QP.  The Q_Key information is exported to
the user through the existing rdma_init_qp_attr() interface.

Multicast support is also exported to userspace through the rdma_ucm.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Randomize the starting port number and avoid re-using port values
immediately after they are closed.  Instead keep track of the last
port value used and increment it every time a new port number is
assigned, to better replicate other port spaces.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The iWARP CM should report timeouts as event RDMA_CM_EVENT_UNREACHABLE,
not event RDMA_CM_EVENT_REJECTED.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Allow the use of UD QPs through the rdma_cm, in order to provide
address translation services for resolving IB addresses for datagram
messages using SIDR.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

During connection establishment, the passive side of a connection can
receive messages from the active side before the connection event has
been delivered to the user.  Allow the passive side to send messages
in response to received data before the event is delivered.  To handle
the case where the connection messages are lost, a new rdma_notify()
function is added that users may invoke to force a connection into the
established state.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Connection information was never given to the recipient of a
connection request or reply message.  Only the event was delivered.
Report the connection data with the event to allows user to
reject the connection based on the requested parameters, or adjust
their resources to match the request.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The qp_type parameter into the rdma_cm is unneeded, and can be
misleading.  The QP type should be determined from the port space.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The qp_access_flags are for remote access permissions only, so
IB_ACCESS_LOCAL_WRITE is an invalid value.  Remove it from the values
set by cm_init_qp_init_attr() and cma_init_ib_qp().
Signed-off-by: NDotan Barak <dotanb@mellanox.co.il>
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Rewrite cma_req_handler error handling case to encapsulate
common code.
Signed-off-by: NKrishna Kumar <krkumar2@in.ibm.com>
Acked-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Remove redundant check of node_guid in cma_add_one().
Signed-off-by: NKrishna Kumar <krkumar2@in.ibm.com>
Acked-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Optimize to test for an empty list first.  This ends up simplifying
the code too.
Signed-off-by: NKrishna Kumar <krkumar2@in.ibm.com>
Acked-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix up for make allyesconfig.
Signed-Off-By: NDavid Howells <dhowells@redhat.com>

Require registration with ib_addr module to prevent caller from
unloading while a callback is in progress.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

rdma_bind_addr() leaks a cma_dev reference count in failure case.
Signed-off-by: NKrishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: NSean Hefty <sean.hefty@intel.com>

Reorganize code relating to cma_get_net_info() and rdam_create_id() to
optimize error case handling (no need to alloc memory/etc. as part of
rdma_create_id() if input parameters are wrong).
Signed-off-by: NKrishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Eliminate remove_list by using list_del_init() instead during device
removal handling.
Signed-off-by: NKrishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

On reporting a route error, also include the status for the error,
rather than indicating a status of 0 when an error has occurred.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The race is as follows:

A process : cma_process_remove() calls cma_remove_id_dev(),
	    which sets id state to CMA_DEVICE_REMOVAL and
	    calls wait_event(dev_remove).

B process : cma_req_handler() had incremented dev_remove,
	    and calls cma_acquire_ib_dev() and on failure
	    calls cma_release_remove(), which does a
	    wake_up of cma_process_remove(). Then
	    cma_req_handler() calls rdma_destroy_id();

A Process : cma_remove_id_dev() gets woken and checks the
	    state of id, and since it is still (wrongly)
	    CMA_DEVICE_REMOVAL, it calls notify_user(id)
	    and if that fails, the caller - cma_process_remove()
	    calls rdma_destroy_id(id). Two processes can
	    call rdma_destroy_id(), resulting in one
	    de-referencing kfreed id_priv.

Fix is for process B to set CMA_DESTROYING in cma_req_handler()
so that process A will return instead of doing a rdma_destroy_id().
Signed-off-by: NKrishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>