This adds support for a new copper device for 82599, device id 0x151c.
This 82599 10GBase-T device uses the PHY's internal temperature sensor
to guard against over-temp conditions. In this scenario the PHY will be
put in a low power mode and link will no longer be able to transmit or
receive any data. When this occurs, the over-temp interrupt is latched
and driver logs this error message. A HW reset or power cycle is
required to clear this status.
Signed-off-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support of active DA cables.  This is
renaming and adding some PHY type enumerations.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The network stack indicate packets should not be DCB
tagged by setting the priority to TC_PRIO_CONTROL. One
usage for this is lldp frames which are not suppossed
to be tagged.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The TFCS bits show the current XON state.  Meaning that the
device is paused if these bits are 0.  This fixes the logic
to work as it was intended.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

when DCB mode is on, we want the HW VLAN stripping to be always enabled.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ETQS setup for FIP out side the if..else is enough for the ETQS
setup for FIP, so remove redundant code.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure we point to the right offset of the fc_frame_header when
VLAN header exists and HW has VLAN stripping disabled.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When in packet split mode, packet type is not recognized, and the packet is
larger than the header size, the 82599 overflows the packet into the data
area, but doesn't set the HDR_LEN field.  We can safely assume the length
is the current header size.  This fixes an obscure corner case that can be
triggered by non-ip packet headers or (more likely) by disabling the L2
packet recognition.
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes from drivers/net/ all the unnecessary
return; statements that precede the last closing brace of
void functions.

It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.

It also does not remove null void functions with return.

Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
  xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'

with some cleanups by hand.

Compile tested x86 allmodconfig only.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of the following MAC functions are moved from 82598 & 82599 specific
hardware files to common.[ch] to accommodate new silicon changes. Also
fixed some white space issues
 * get_san_mac_addr, check_link, set_vmdq, clear_vmdq, clear_vfta,
 * set_vfta, fc_enable, init_uta_tables
Signed-off-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We can't use zero magic "bad" value to check if IXGBE_RSC_CB(skb)->dma
is valid. It is only valid in x86/arm/m68k/alpha architectures and in
spark, powerPC and other architectures it should be ~0. As per
Benjamin Herrenschmidt feedback use a bool flag to decide if
the packet unmapping is delayed in hardware RSC till EOP is reached
Signed-off-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce uc_set_promisc flag to fix enabling of promisc mode
when exceeding the number of supported RAR entries.

Issue discovered by Ben Greear when using mac-vlans.
Reported-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver was calling the set Rx mode function for every multicast
filter set by the VF.  When starting many VMs where each might have
multiple VLAN interfaces this would result in the function being
called hundreds or even thousands of times.  This is unnecessary
for the case of the imperfect filters used in the MTA and has been
streamlined to be more efficient.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver is unnecessarily writing values to VLAN control registers.
These writes already done elsewhere and are superfluous here.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the "ip link set" and "ip link show" commands that allow
configuration of the virtual functions' MAC and port VLAN via user space
command line.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a boolean parameter to ixgbe-set_vmolr so that the caller can
specify whether the pool should accept untagged packets.  Required
for a follow on patch to enable administrative configuration of port
VLAN for virtual functions.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit d5ffd75a.

As requested by Jeff Kircher.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to an errata in 82598 parts MSI-X needs to be disabled
in certain ixgbe devices designed to transfer peer-to-peer
traffic on the PCIe bus. This patch sets the default
interrupt type to MSI rather than MSI-X for specific Cisco
ixgbe adapters.
Signed-off-by: NNicholas Nunley <nicholasx.d.nunley@intel.com>
Acked-by: NJohn Ronciak <john.ronciak@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds registers (,tx/rx rings' status and so on) printout
code just before resetting adapters. This will be helpful for detecting
the root cause of adapters reset.
Signed-off-by: NTaku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: NKoki Sanagi <sanagi.koki@jp.fujitsu.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NNicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Description: When using Intel smartspeed, the patch displays a
warning when the link down shifts to 1 Gig.
Signed-off-by: NAnjali Singhai <anjali.singhai@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The way we were setting autoneg via ethtool was inconstant with that
of our other drivers.  It will change the following:

If autoneg is off:
>ethtool -a eth0
Pause parameters for eth0:

Autonegotiate:  off
RX:             off
TX:             off

Before:
>ethtool -A eth0 autoneg on
>ethtool -a eth0
Pause parameters for eth0:

Autonegotiate:  off
RX:             off
TX:             off

Now:
>ethtool -A eth0 autoneg on
>ethtool -a eth0
Pause parameters for eth0:

Autonegotiate:  on
RX:             on
TX:             on
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a small race between when the tx queues are stopped
and when netif_carrier_off() is called in ixgbe_down.  If the
dev_watchdog() timer fires during this time it is possible for
a false tx timeout to occur.

This patch moves the netif_carrier_off() so that it is called before
the tx queues are stopped preventing the dev_watchdog timer from
detecting false tx timeouts.  The race is seen occosionally when
FCoE or DCB settings are being configured or changed.

Testing note, running ifconfig up/down will not reproduce this
issue because dev_open/dev_close call dev_deactivate() and then
dev_activate().
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

writebacks can be held indefinitely by hardware if EITR=0, when
combined with TXDCTL.WTHRESH=8.  When EITR=0, WTHRESH should be
set back to zero.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

82598/82599 can support EITR == 0, which allows for the
absolutely lowest latency setting in the hardware.  This disables
writeback batching and anything else that relies upon a delayed
interrupt. This patch enables the feature of "override" when a
user sets rx-usecs to zero, the driver will respect that setting
over using RSC, and automatically disable RSC.  If rx-usecs is
used to set the EITR value to 0, then the driver should disable
LRO (aka RSC) internally until EITR is set to non-zero again.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PHY laser is still on during driver init.  It's allowing
garbage to hit our FIFO, which eventually can cause the entire
device to die.  Power down the laser while setting up the device,
and re-enable the laser before getting link.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ixgbe driver was setting up 82598 hardware correctly, so that
when promiscuous mode was enabled hardware stripping was turned
off.  But on 82599 the logic to disable/enable hardware stripping
is different, and the code was not updated correctly when the
hardware vlan stripping was enabled as default.

This change comprises the creation of two new helper functions
and calling them from the right locations to disable and enable
hardware stripping of vlan tags at appropriate times.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Converts the list and the core manipulating with it to be the same as uc_list.

+uses two functions for adding/removing mc address (normal and "global"
 variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
 manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: NTejun Heo <tj@kernel.org>
Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>

When running the offline diagnostic tests check to see if any VFs are
online.  If so then only run the link test.  This is necessary because
the VFs running in guest VMs aren't aware of when the PF is taken
offline for a diagnostic test.  Also put a message to the system log
telling the system administrator to take the VFs offline manually if
(s)he wants to run a full diagnostic.  Return 1 on each of the tests
not run to alert the user of the condition.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During FCF solicitation, the switch is supposed to pad the
solicited advertisement out to the endpoints specified
maximum FCoE frame size.  That means that we need to receive
FIP frames that are larger than the standard MTU.  To make
sure the receive queue is configured correctly, we should be
filtering FIP traffic into the FCoE queues.
Signed-off-by: NChris Leech <christopher.leech@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently FIP (FCoE Initialization Protocol) frames
are going untagged. This causes various problems
with FCFs (switches) that have negotiated a priority
over dcbx. This patch tags FIP frames with the same
priority as the FCoE frames.
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NChris Leech <christopher.leech@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the user buffer count was 256 the shift would place a 1
in the offset region leading to errors. It also overwrites
the uers buffer list. This patch makes sure that at most
256 user buffers are allowed for DDP and the buffer count
is masked properly such that it doesn't overwrite the offset
when shifting the bits.
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NFrank Zhang <frank_1.zhang@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the last patch I missed an unecessary min_t comparison.
This patch removes it, the path allocates at most
72 tx queues for 82599 and 24 for 82598 there is no need
for this check.

Additionally this sets MAX_[TX|RX]_QUEUES to 72.  Which is
used as the size for the tx/rx_ring arrays. There is no
reason to have more tx_rings/rx_rings then num_tx_queues.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The clear_to_send flag is being cleared before the call to ping all
the VFs.  It should be called after pinging all the VFs.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VFs running in guest VMs do not respond in as timely a manner to
PF indication it is going down as they do when running in the host
domain.  If the adapter is in SR-IOV mode insert a two second delay
to guarantee that all VFs have had time to respond to the PF reset.
In any case resetting the PF while VFs are active should be
discouraged but if it must be done then there will be a two
second delay to help synchronize resets among the PF and all the
VFs.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Includes one minor indentation fix to placate checkpatch.
Signed-off-by: NFrans Pop <elendil@planet.nl>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As per Simon Horman's feedback set IXGBE_RSC_CB(skb)->dma to zero
after unmapping HWRSC DMA address to avoid double freeing.
Signed-off-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently netdev_features_change is called before fcoe tx queues
setup is done, so this patch moves calling of netdev_features_change
after tx queues setup is done in ixgbe_init_interrupt_scheme, so
that real_num_tx_queues is updated correctly on each fcoe enable
or disable.

This allows additional fcoe queues updated correctly in vlan driver
for their correct queue selection.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>