[media] em28xx-video: do not unregister the v4l2 dummy clock before v4l2_device_unregister() has been called

Otherwiese the core refuses to unregister the clock and the following warning
appears in the system log:

"WARNING: ... at drivers/media/v4l2-core/v4l2-clk.c:231 v4l2_clk_unregister+0x8a/0x90 [videodev]()
 v4l2_clk_unregister(): Refusing to unregister ref-counted 11-0030:mclk clock!"
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

dev->adev.users always needs to be increased when snd_em28xx_capture_open() is
called and succeeds.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add a raw decoder for the Sharp protocol. It uses a pulse distance
modulation with a pulse of 320us and a bit period of 2ms for a logical 1
and 1ms for a logical 0. The first part of the message consists of a
5-bit address, an 8-bit command, and two other bits, followed by a 40ms
gap before the echo message which is an inverted version of the main
message except for the address bits.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: linux-media@vger.kernel.org
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add Sharp infrared protocol constants RC_TYPE_SHARP and RC_BIT_SHARP.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Briefly document /sys/class/rc/ API for remote controller devices in
Documentation/ABI/teting.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Since v3.12, specifically 153a60bb ([media] rc: add feedback led
trigger for rc keypresses), an LED trigger is activated on IR keydown
whether or not a keypress is generated (i.e. even if there's no matching
keycode). However the repeat and keyup logic isn't used unless there is
a keypress, which results in non-keypress keydown events turning on the
LED and not turning it off again.

On the assumption that the intent was for the LED only to light up on
valid key presses (you probably don't want it lighting up for the wrong
remote control for example), move the led_trigger_event() call inside
the keycode check.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Acked-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Around 01/14/2014 06:07 PM, Mauro Carvalho Chehab scribbled:
> Em Tue, 14 Jan 2014 17:55:19 +0200
> Georgi Chorbadzhiyski <gf@unixsol.org> escreveu:
>> Around 01/14/2014 05:30 PM, Mauro Carvalho Chehab scribbled:
>>> Em Tue, 14 Jan 2014 17:16:10 +0200
>>> Georgi Chorbadzhiyski <gf@unixsol.org> escreveu:

> >>>> Hi guys, I'm confused the documentation on:
> >>>>
> >>>> http://linuxtv.org/downloads/v4l-dvb-apis/frontend_fcalls.html#FE_READ_SNR
> >>>> http://linuxtv.org/downloads/v4l-dvb-apis/frontend_fcalls.html#FE_READ_SIGNAL_STRENGTH
> >>>>
> >>>> states that these ioctls return int16_t values but frontend.h states:
> >>>>
> >>>> https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/tree/include/uapi/linux/dvb/frontend.h
> >>>>
> >>>> #define FE_READ_SIGNAL_STRENGTH  _IOR('o', 71, __u16)
> >>>> #define FE_READ_SNR              _IOR('o', 72, __u16)
> >>>>
> >>>> So which one is true?

>>> Documentation is wrong. The returned values are unsigned. Would you mind send
>>> us a patch fixing it?
>>
>> I would be happy to, but I can't find the repo that holds the documentation.
>
> It is in the Kernel tree, under Documentation/DocBook/media/dvb.

The attached file contains the discussed documentation fixes.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Fix sparse warning:
	drivers/media/rc/rc-main.c:27:1: sparse: symbol 'ir_core_dev_number' was not declared. Should it be static?
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Fix sparse warning:
	drivers/media/usb/em28xx/em28xx-cards.c:69:1: sparse: symbol 'em28xx_devused' was not declared. Should it be static?
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This section was horribly out of date. A lot of references to old and
obsolete behavior have been dropped.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

[m.chehab@samsung.com: removed "Opening and Closing Devices" from the
 list of changes, as the patch with such change weren't applied]
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The old table is most definitely wrong. All applications and all
drivers that I have ever tested follow the corrected table. Furthermore,
that's what all applications expect as well. Any drivers that do not
follow the corrected table are broken and should be fixed.

This patch drops the old table and replaces it with the corrected
table. This should prevent a lot of confusion.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Updates for the "Tuners and Modulators", "Video Standards" and
"Digital Video (DV) Timings" sections.

Besides lots of trivial little fixes the main changes are:

- Remove two footnotes from "Video Standards": the first is a discussion
  of alternative methods of setting standards, which is pretty pointless
  since the standards API is effectively frozen anyway, and the second
  points to 'rationale' that makes little or no sense to me.

- Clarify a few things in the "Digital Video (DV) Timings" section.
  It was awkwardly formatted as well: there used to be a list with
  multiple bullets that has been reduced to a single item, so drop the
  list and rewrite that text.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Updates sections "Querying Capabilities", "Application Priority",
"Video Inputs and Outputs" and "Audio Inputs and Outputs".
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

It's now 2014, so update those copyright years. Also fix a typo in the introduction
and mention that this document also covers output, codec and remote control
devices.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Mauro's old redhat email address is no longer valid, update to the
current email address.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The VESA standard added a version 2 of the reduced blanking formula.
Note in the comment that this is not yet supported by the v4l2_detect_cvt
function. Obviously this should be implemented eventually, but for now add
this as a reminder.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

VESA added two new DMT timings in their latest standard document. Add these
to v4l2-dv-timings.h.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Fixes all style warnings from scripts/checkpatch -f
Signed-off-by: NDean Anderson <linux-dev@sensoray.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

module_usb_driver eliminates the boilerplate and makes the code simpler.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This applies to HDMI-map register 0x69.
So far we have been using HPA manual mode.
This way we had control of HPA which could be
set after EDID had been programmed.

Using a Mac Mini with mini-displayport to DVI-D converter as source
caused the adv7842 to lock up and fail to detect any further signals.

After experimenting with different configurations it was found that
using the HPA auto mode and in addition letting RX-termination
be controlled by HPA prevented this error from occuring.

I was not able to re-create this problem on the adv7604.
Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Clear any pending AVI checksum-errors.
To be able to display last received AVI.
Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Incorrect registers used for pixelclock read-out.
Same registers as for adv7604 which actually gave an almost
correct read-out, even they are not documented for adv7842.
Corrected deep-color pixel-clock correction.
Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

If the input signal is DVI-D and quantization range is RGB full range,
gain and offset must be adjusted to get the right range on the output.
Copied and adopted from adv7604.
Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

I came across this while checking the kernel use of V4L2_CTRL_FLAG_DISABLED.

This flag should not be used with the control framework. Instead, just don't
add the control at all.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This define uses the deprecated interruptible_sleep_on_timeout
function. Since this define is unused anyway we just remove it.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

usbtv-video.c needs module.h. So move the module.h include from usbtv-core.c to usbtv.h,
that way both core.c and video.c have it.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NFederico Simoncelli <fsimonce@redhat.com>
Reviewed-by: NLubomir Rintel <lkundrak@v3.sk>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Linus 3.14-rc1

* tag 'v3.14-rc1': (11781 commits)
  Linus 3.14-rc1
  hpfs: optimize quad buffer loading
  hpfs: remember free space
  parisc: add flexible mmap memory layout support
  parisc: Make EWOULDBLOCK be equal to EAGAIN on parisc
  parisc: convert uapi/asm/stat.h to use native types only
  parisc: wire up sched_setattr and sched_getattr
  parisc: fix cache-flushing
  parisc/sti_console: prefer Linux fonts over built-in ROM fonts
  hwmon: Fix SENSORS_TMP102 dependencies to eliminate build errors
  hwmon: Fix SENSORS_LM75 dependencies to eliminate build errors
  tools/power turbostat: introduce -s to dump counters
  tools/power turbostat: remove unused command line option
  afs: proc cells and rootcell are writeable
  tile: remove compat_sys_lookup_dcookie declaration to fix compile error
  Revert "PCI: Remove from bus_list and release resources in pci_release_dev()"
  ARM: multi_v7_defconfig: remove redundant entries and re-enable TI_EDMA
  ARM: multi_v7_defconfig: add mvebu drivers
  clocksource: kona: Add basic use of external clock
  drivers: bus: fix CCI driver kcalloc call parameters swap
  ...

Pull parisc updates from Helge Deller:
 "The three major changes in this patchset is a implementation for
  flexible userspace memory maps, cache-flushing fixes (again), and a
  long-discussed ABI change to make EWOULDBLOCK the same value as
  EAGAIN.

  parisc has been the only platform where we had EWOULDBLOCK != EAGAIN
  to keep HP-UX compatibility.  Since we will probably never implement
  full HP-UX support, we prefer to drop this compatibility to make it
  easier for us with Linux userspace programs which mostly never checked
  for both values.  We don't expect major fall-outs because of this
  change, and if we face some, we will simply rebuild the necessary
  applications in the debian archives"

* 'parisc-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: add flexible mmap memory layout support
  parisc: Make EWOULDBLOCK be equal to EAGAIN on parisc
  parisc: convert uapi/asm/stat.h to use native types only
  parisc: wire up sched_setattr and sched_getattr
  parisc: fix cache-flushing
  parisc/sti_console: prefer Linux fonts over built-in ROM fonts

HPFS needs to load 4 consecutive 512-byte sectors when accessing the
directory nodes or bitmaps.  We can't switch to 2048-byte block size
because files are allocated in the units of 512-byte sectors.

Previously, the driver would allocate a 2048-byte area using kmalloc,
copy the data from four buffers to this area and eventually copy them
back if they were modified.

In the current implementation of the buffer cache, buffers are allocated
in the pagecache.  That means that 4 consecutive 512-byte buffers are
stored in consecutive areas in the kernel address space.  So, we don't
need to allocate extra memory and copy the content of the buffers there.

This patch optimizes the code to avoid copying the buffers.  It checks
if the four buffers are stored in contiguous memory - if they are not,
it falls back to allocating a 2048-byte area and copying data there.
Signed-off-by: NMikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Previously, hpfs scanned all bitmaps each time the user asked for free
space using statfs.  This patch changes it so that hpfs scans the
bitmaps only once, remembes the free space and on next invocation of
statfs it returns the value instantly.

New versions of wine are hammering on the statfs syscall very heavily,
making some games unplayable when they're stored on hpfs, with load
times in minutes.

This should be backported to the stable kernels because it fixes
user-visible problem (excessive level load times in wine).
Signed-off-by: NMikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Cc: stable@vger.kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for the flexible mmap memory layout (as described in
http://lwn.net/Articles/91829). This is especially very interesting on
parisc since we currently only support 32bit userspace (even with a
64bit Linux kernel).
Signed-off-by: NHelge Deller <deller@gmx.de>

On Linux, only parisc uses a different value for EWOULDBLOCK which
causes a lot of troubles for applications not checking for both values.
Since the hpux compat is long dead, make EWOULDBLOCK behave the same as
all other architectures.
Signed-off-by: NGuy Martin <gmsoft@tuxicoman.be>
Signed-off-by: NHelge Deller <deller@gmx.de>

The stat.h header file is exported to userspace. Some userspace
applications failed to compile due to missing/unknown types, so we
better convert it to use native types only (like it's done on other
architectures too).
Signed-off-by: NHelge Deller <deller@gmx.de>

Signed-off-by: NHelge Deller <deller@gmx.de>

This commit:
f8dae006: parisc: Ensure full cache coherency for kmap/kunmap
caused negative caching side-effects, e.g. hanging processes with expect and
too many inequivalent alias messages from flush_dcache_page() on Debian 5 systems.

This patch now partly reverts it and has been in production use on our debian buildd
makeservers since a week without any major problems.
Signed-off-by: NHelge Deller <deller@gmx.de>
Signed-off-by: NJohn David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: NHelge Deller <deller@gmx.de>

The built-in ROM fonts lack many necessary ASCII characters, which is
why it makes sens to prefer the Linux fonts instead if they are
available.  This makes consoles on STI graphics cards which are not
supported by the stifb driver (e.g. Visualize FXe) looks much nicer.
Signed-off-by: NHelge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v3.13

Pull hwmon kconfig fixes from Jean Delvare.

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: Fix SENSORS_TMP102 dependencies to eliminate build errors
  hwmon: Fix SENSORS_LM75 dependencies to eliminate build errors