For SKL and later Intel chips, we control the power well per codec
basis via link_power callback since the commit [03b135ce: ALSA:
hda - remove dependency on i915 power well for SKL].
However, there are a few exceptional cases where the gfx registers are
accessed from the audio driver: namely the wakeup override bit
toggling at (both system and runtime) resume.  This seems causing a
kernel warning when accessed during the power well down (and likely
resulting in the bogus register accesses).

This patch puts the proper power up / down sequence around the resume
code so that the wakeup bit is fiddled properly while the power is
up.  (The other callback, sync_audio_rate, is used only in the PCM
callback, so it's guaranteed in the power-on.)

Also, by this proper power up/down, the instantaneous flip of wakeup
bit in the resume callback that was introduced by the commit
[033ea349: ALSA: hda - Fix Skylake codec timeout] becomes
superfluous, as snd_hdac_display_power() already does it.  So we can
clean it up together.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96214
Fixes: 03b135ce ('ALSA: hda - remove dependency on i915 power well for SKL')
Cc: <stable@vger.kernel.org> # v4.2+
Tested-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Skylake onwards HDA controller supports new capabilities like
Global Time Stamping (GTS) capability. So add support to parse
these new capabilities.
Signed-off-by: NGuneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: NHardik T Shah <hardik.t.shah@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit fixes garbled audio on Bonaire HDMI
Signed-off-by: NMaruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This allows the device to correctly show up as ATI HDMI
rather than a generic one and allows the driver to use
the available caps.
Signed-off-by: NAwais Belal <awais_belal@mentor.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

register_vga_switcheroo() sets the PM ops from the hda structure which
is freed later in azx_free. Make sure that these ops are cleared.

Caught by KASAN, initially noticed due to a general protection fault.

Fixes: 246efa4a ("snd/hda: add runtime suspend/resume on optimus support (v4)")
Signed-off-by: NPeter Wu <peter@lekensteyn.nl>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Kabylake-H shows up as PCI ID 0xa2f0. We missed adding this
earlier with other KBL IDs.
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Kabylake shows up as PCI ID 0xa171. And Kabylake-LP as 0x9d71.
Since these are similar to Skylake add these to SKL_PLUS macro
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The recent bug report suggests that BCLK setup for i915 HSW/BDW needs
to be updated at each HDMI hotplug, not only at initialization and
resume.  That is, we need to update HSW_EM4 and HSW_EM5 registers at
ELD notification, too.  Otherwise the HDMI audio may be out of sync
and played in a wrong pitch.

However, the HDA codec driver has no access to the controller
registers, and currently the code managing these registers is in
hda_intel.c, i.e. local to the controller driver.  For allowing the
explicit BCLK update from the codec driver, as in this patch, the
former haswell_set_bclk() in hda_intel.c is moved to hdac_i915.c and
exposed as snd_hdac_i915_set_bclk().  This is called from both the HDA
controller driver and intel_pin_eld_notify() in HDMI codec driver.

Along with this change, snd_hdac_get_display_clk() gets dropped as
it's no longer used.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91410
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add HD Audio Device PCI ID for the Intel Broxton-T platform.
It is an HDA Intel PCH controller.
Signed-off-by: NLu, Han <han.lu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit fixes garbled audio on Polaris-10/11 variants
Signed-off-by: NMaruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

azx_probe_continue() uses pm_runtime_put_noidle() to drop the rpm
usage_count, which means that if it's the last reference the
autosuspend of the controller won't actually happen. So if the codecs
autosuspend before the azx_probe_continue() drops the last
reference we'll fail to autosuspend the controller. This does happen
in practice, but not every time. As can be seen in [1] the controller
autosuspend attempt fails due to the usage_count when suspending the
codecs. A bit later we see the the contoller usage_count dropping to
zero without further attempts at autosuspend.

Fix the problem by using pm_runtime_put_autosuspend() instead, which
will kick off the autosuspend of the controller even if the codecs
are already asleep. As can be seen in [2] the controller autosuspend
still fails while suspending the codecs, but later on we see another
autosuspend attempt after dropping the usage_count to 0.

I was also a bit worried that there might still be a race between the
controller autosuspend and the rest of the code in azx_probe_continue().
So I also tried replacing the the put_noidle() with put_sync_suspend().
No explosions occurred, so I'm somewhat satisfied that there are no
serious problems in this area.

[1]
 kworker/1:2-122   [001] ....    63.661310: __pm_runtime_suspend: hdaudioC0D0 usage_count 0
 kworker/1:2-122   [001] d..2    63.661316: rpm_suspend: hdaudioC0D0 flags-d cnt-0  dep-0  auto-1 p-0 irq-0 child-0
 kworker/1:2-122   [001] d..1    63.661317: rpm_check_suspend_allowed: hdaudioC0D0 retval 0
 kworker/1:2-122   [001] d..2    63.661332: rpm_return_int: rpm_suspend+0x406/0x5e8:hdaudioC0D0 ret=0
 kworker/1:1-72    [001] d..2    63.661543: rpm_suspend: hdaudioC0D0 flags-a cnt-0  dep-0  auto-1 p-0 irq-0 child-0
 kworker/1:1-72    [001] d..1    63.661544: rpm_check_suspend_allowed: hdaudioC0D0 retval 0
 kworker/1:1-72    [001] ....    63.661545: hda_codec_runtime_suspend: hdaudioC0D0 suspend
 kworker/1:1-72    [001] d..2    63.661614: rpm_idle: 0000:00:03.0 flags-1 cnt-1  dep-0  auto-1 p-0 irq-0 child-0
 kworker/1:1-72    [001] d..1    63.661615: rpm_check_suspend_allowed: 0000:00:03.0 usage_count 1
 kworker/1:1-72    [001] d..1    63.661615: rpm_check_suspend_allowed: 0000:00:03.0 retval -11
 kworker/1:1-72    [001] d..2    63.661616: rpm_return_int: rpm_idle+0x249/0x487:0000:00:03.0 ret=-11
 kworker/1:1-72    [001] d..2    63.661616: rpm_return_int: rpm_suspend+0x406/0x5e8:hdaudioC0D0 ret=0
 kworker/1:2-122   [001] d..2    63.664834: rpm_idle: hdaudioC0D0 flags-8 cnt-0  dep-0  auto-1 p-0 irq-0 child-0
 kworker/1:2-122   [001] d..1    63.664835: rpm_check_suspend_allowed: hdaudioC0D0 retval 1
 kworker/1:2-122   [001] d..2    63.664836: rpm_return_int: rpm_idle+0x249/0x487:hdaudioC0D0 ret=-11
 kworker/1:2-122   [001] d..2    63.664841: rpm_idle: hdaudioC0D0 flags-8 cnt-0  dep-0  auto-1 p-0 irq-0 child-0
 kworker/1:2-122   [001] d..1    63.664841: rpm_check_suspend_allowed: hdaudioC0D0 retval 1
 kworker/1:2-122   [001] d..2    63.664841: rpm_return_int: rpm_idle+0x249/0x487:hdaudioC0D0 ret=-11
 kworker/1:2-122   [001] ....    63.664842: azx_probe_continue: 0000:00:03.0 usage_count=0

[2]
 kworker/0:0-4     [000] ....    50.354567: __pm_runtime_suspend: hdaudioC0D0 usage_count 0
 kworker/0:0-4     [000] d..2    50.354574: rpm_suspend: hdaudioC0D0 flags-d cnt-0  dep-0  auto-1 p-0 irq-0 child-0
 kworker/0:0-4     [000] d..1    50.354575: rpm_check_suspend_allowed: hdaudioC0D0 retval 0
 kworker/0:0-4     [000] d..2    50.354589: rpm_return_int: rpm_suspend+0x406/0x5e8:hdaudioC0D0 ret=0
 kworker/0:2-135   [000] d..2    50.354809: rpm_suspend: hdaudioC0D0 flags-a cnt-0  dep-0  auto-1 p-0 irq-0 child-0
 kworker/0:2-135   [000] d..1    50.354810: rpm_check_suspend_allowed: hdaudioC0D0 retval 0
 kworker/0:2-135   [000] ....    50.354816: hda_codec_runtime_suspend: hdaudioC0D0 suspend
 kworker/0:2-135   [000] d..2    50.354908: rpm_idle: 0000:00:03.0 flags-1 cnt-1  dep-0  auto-1 p-0 irq-0 child-0
 kworker/0:2-135   [000] d..1    50.354909: rpm_check_suspend_allowed: 0000:00:03.0 usage_count 1
 kworker/0:2-135   [000] d..1    50.354909: rpm_check_suspend_allowed: 0000:00:03.0 retval -11
 kworker/0:2-135   [000] d..2    50.354909: rpm_return_int: rpm_idle+0x249/0x487:0000:00:03.0 ret=-11
 kworker/0:2-135   [000] d..2    50.354910: rpm_return_int: rpm_suspend+0x406/0x5e8:hdaudioC0D0 ret=0
 kworker/0:0-4     [000] d..2    50.373791: rpm_idle: hdaudioC0D0 flags-8 cnt-0  dep-0  auto-1 p-0 irq-0 child-0
 kworker/0:0-4     [000] d..1    50.373792: rpm_check_suspend_allowed: hdaudioC0D0 retval 1
 kworker/0:0-4     [000] d..2    50.373793: rpm_return_int: rpm_idle+0x249/0x487:hdaudioC0D0 ret=-11
 kworker/0:0-4     [000] d..2    50.373797: rpm_idle: hdaudioC0D0 flags-8 cnt-0  dep-0  auto-1 p-0 irq-0 child-0
 kworker/0:0-4     [000] d..1    50.373798: rpm_check_suspend_allowed: hdaudioC0D0 retval 1
 kworker/0:0-4     [000] d..2    50.373798: rpm_return_int: rpm_idle+0x249/0x487:hdaudioC0D0 ret=-11
 kworker/0:0-4     [000] ....    50.373799: __pm_runtime_suspend: 0000:00:03.0 usage_count 0
 kworker/0:0-4     [000] d..2    50.373800: rpm_suspend: 0000:00:03.0 flags-d cnt-0  dep-0  auto-1 p-0 irq-0 child-0
 kworker/0:0-4     [000] d..1    50.373800: rpm_check_suspend_allowed: 0000:00:03.0 retval 0
 kworker/0:0-4     [000] d..2    50.373803: rpm_return_int: rpm_suspend+0x406/0x5e8:0000:00:03.0 ret=0
 kworker/0:0-4     [000] d..2    50.385164: rpm_suspend: 0000:00:03.0 flags-a cnt-0  dep-0  auto-1 p-0 irq-0 child-0
 kworker/0:0-4     [000] d..1    50.385165: rpm_check_suspend_allowed: 0000:00:03.0 retval 0
 kworker/0:0-4     [000] ....    50.385174: azx_runtime_suspend: 0000:00:03.0 azx suspend releaseing power well
 kworker/0:0-4     [000] ....    50.385179: azx_runtime_suspend: 0000:00:03.0 azx suspend
 kworker/0:0-4     [000] d..2    50.386872: rpm_return_int: rpm_suspend+0x406/0x5e8:0000:00:03.0 ret=0
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Some Skylake machines show the codec probe errors in certain
situations, e.g. HP Z240 desktop fails to probe the onboard Realtek
codec at reloading the snd-hda-intel module like:
  snd_hda_intel 0000:00:1f.3: spurious response 0x200:0x2, last cmd=0x000000
  snd_hda_intel 0000:00:1f.3: azx_get_response timeout, switching to polling mode: lastcmd=0x000f0000
  snd_hda_intel 0000:00:1f.3: No response from codec, disabling MSI: last cmd=0x000f0000
  snd_hda_intel 0000:00:1f.3: Codec #0 probe error; disabling it...
  hdaudio hdaudioC0D2: no AFG or MFG node found
  snd_hda_intel 0000:00:1f.3: no codecs initialized

Also, HP G470 G3 suffers from the similar problem, as reported in
bugzilla below.  On this machine, the codec probe error appears even
at a fresh boot.

As Libin suggested, the same workaround used for Broxton in the commit
[6639484d: ALSA: hda - disable dynamic clock gating on Broxton
 before reset] can be applied for Skylake in order to fix this problem.
The Intel HW team also confirmed that this is needed for SKL.

This patch makes the workaround applied to both SKL and BXT
platforms.  The referred macros are moved and one superfluous macro
(IS_BROXTON()) is another one (IS_BXT()) as well.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=112731Suggested-by: NLibin Yang <libin.yang@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The commit [991f86d7: ALSA: hda - Flush the pending probe work at
remove] introduced the sync of async probe work at remove for fixing
the race.  However, this may lead to another hangup when the module
removal is performed quickly before starting the probe work, because
it issues flush_work() and it's blocked forever.

The workaround is to use cancel_work_sync() instead of flush_work()
there.

Fixes: 991f86d7 ('ALSA: hda - Flush the pending probe work at remove')
Cc: <stable@vger.kernel.org> # v3.17+
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

On Broxton, to make sure the reset controller works properly,
MISCBDCGE bit (bit 6) in CGCTL (0x48) of PCI configuration space
need be cleared before reset and set back to 1 after reset.
Otherwise, it may prevent the CORB/RIRB logic from being reset.
Signed-off-by: NLibin Yang <libin.yang@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

As HD-audio driver does deferred probe internally via workqueue, the
driver might go into the mixed state doing both probe and remove when
the module gets unloaded during the probe work.  This eventually
triggers an Oops, unsurprisingly.

For avoiding this race, we just need to flush the pending probe work
explicitly before actually starting the resource release.

Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=960710
Cc: <stable@vger.kernel.org> # v3.17+
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Currently HD-audio driver on Intel Skylake or Broxteon gives an error
message when binding with i915 audio component fails.  However, this
isn't any serious error on a system without Intel graphics.  Indeed
there are such systems, where a third-party codec (e.g. Creative) is
put on the mobo while using other discrete GPU (e.g. Nvidia).
Printing a kernel "error" message is overreaction in such a case.

This patch downgrades the print level for that message.  For systems
that mandate the i915 binding (e.g. Haswell or Broadwell HDMI/DP),
another kernel error message is shown in addition to make clear what
went wrong.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=111021Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Currently the info in /proc/interrupts doesn't allow to figure out which
interrupt belongs to which card (HDMI, PCH, ..).
Therefore add card details to the interrupt description.
With the patch the info in /proc/interrupts looks like this:

PCI-MSI 442368-edge      snd_hda_intel:card1
PCI-MSI 49152-edge      snd_hda_intel:card0

NOTE: this patch adds the new irq_descr field snd_card struct that is
filled automatically at a card object creation.  This can be used
generically for other drivers as well.  The changes for others will
follow later -- tiwai
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

It takes three minutes to enter into hibernation on some OEM SKL
machines and we see many codec spurious response after thaw() opertion.
This is because HDA is still in D0 state after freeze() call and
pci_pm_freeze/pci_pm_freeze_noirq() don't set D3 hot in pci_bus driver.
It seems bios still access HDA when system enter into freeze state,
HDA will receive codec response interrupt immediately after thaw() call.
Because of this unexpected interrupt, HDA enter into a abnormal
state and slow down the system enter into hibernation.

In this patch, we put HDA into D3 hot state in azx_freeze_noirq() and
put HDA into D0 state in azx_thaw_noirq().

V2: Only apply this fix to SKL+
    Fix compile error when CONFIG_PM_SLEEP isn't defined

[Yet another fix for CONFIG_PM_SLEEP ifdef and the additional comment
 by tiwai]
Signed-off-by: NXiong Zhang <xiong.y.zhang@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

AZX_DCAPS_REVERSE_ASSIGN is no longer referred by any code.
Let's drop it.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

AZX_DCAPS_POSFIX_VIA is coupled always with AZX_DRIVER_VIA type, so we
don't have to keep this bit in dcaps.  Save one more!
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

AZX_DCAPS_RIRB_DELAY is dedicated only for Nvidia and its purpose is
just to set a flag in bus.  So it's better to be set in the toplevel
driver, either hda_intel.c or hda_tegra.c, instead of the common
hda_controller.c.  This also allows us to strip this flag from dcaps,
so save one more bit there.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

AZX_DCAPS_RIRB_PRE_DELAY is always tied with AZX_DCAPS_CTX_WORKAROUND,
which is Creative's XFi specific.  So, we can replace it and reduce
one more bit free for DCAPS.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Intel Atom processors seem to have a problem at recording when
bdl_pos_adj is set to an odd value.  When a value like 1 is used, it
may drop the samples unexpectedly.  Actually, for the old Atoms, we
used to set AZX_DRIVER_SCH type, and this assigns 32 as default.
Meanwhile the newer chips, Baytrail and Braswell, are set as
AZX_DRIVER_PCH, and the lower default value, 1, is assigned.

This patch changes the default values for these chipsets to a safer
default, 32, again.  Since changing the driver type (AZX_DRIVER_XXX)
leads to the rename of the driver string, it would result in a
possible regression.  So, we can't change the type.  Instead, in this
patch, manual (ugly) PCI ID checks are added on top.

A drawback by this increase is the slight increase of the latency, but
it's a sub-ms order in normal situations, so mostly negligible.
Reported-and-tested-by: NJochen Henneberg <jh@henneberg-systemdesign.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Just a minor cleanup; instead of passing an array, pass the assigned
bdl_pos_adj option value directory in struct azx.  Also split the code
to get the default bdl_pos_adj value for the change that will follow
after this.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Due to the recent change, HDA controller driver for Intel PCH tries to
bind i915 audio component always at the probe time no matter whether
HDMI/DP codec is found.  This is, however, superflulous for old
chipsets (e.g. on IVB) where they don't have always the HDMI/DP codecs
but  often have only a discrete GPU instead.

For the newer chipsets, we need already the i915 binding from the
beginning due to power well control.  Meanwhile, for older chipsets
where we don't need power well, we don't need the i915 binding at the
controller level.

This patch removes again the i915 binding in the HDA controller driver
for old Intel PCHs, but adds the binding in HDMI/DP codec driver
instead.  This allows still the use of the direct notification from
the graphics driver while we can avoid the unnecessary load of i915
driver for machines only with another GPU.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The recent commit [6603249d: ALSA: hda - Enable audio component
for old Intel PCH devices] enabled the i915 binding for HDMI/DP on old
Intel PCHs.  But many boards are without HDMI/DP, and they actually
don't need i915 binding, and yet the driver has a check of i915
binding and complains like
	Haswell must be built with CONFIG_SND_HDA_I915
This error is false-positive, and it should be put only for HSW/BDW,
instead of all devices that may be bound with i915.

This patch fixes the condition to check, as well as rephrasing the
message specific to HSW/BDW HDMI/DP.

Fixes: 6603249d ('ALSA: hda - Enable audio component for old Intel PCH devices')
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In BXT-P A0, HD-Audio DMA requests is later than expected,
and makes an audio stream sensitive to system latencies when
24/32 bits are playing.
Adjusting threshold of DMA fifo to force the DMA request
sooner to improve latency tolerance at the expense of power.

v2: move Intel specific code to hda_intel.c
Signed-off-by: NLu, Han <han.lu@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

As i915 graphics driver provides the notification via audio component,
not only the currently implemented HSW+ and VLV+ platforms but also
all other PCH-based platforms (e.g. Cougar Point, Panther  Point, etc)
can use this infrastructure.  It'll improve the reliability and the
power consumption significantly, especially once when we implement the
ELD notification via component.  As a preliminary, this patch enables
the usage of audio component for all PCH platforms.

The HDA controller just needs to set AZX_DCAPS_I915_POWERWELL flag
appropriately.  The name of the flag is a bit confusing, but this
actually works even on the chips without the powerwell but accesses
only the other component ops.

In the HDMI/DP codec driver side, we just need to register/unregister
the notifier for such chips.  This can be identified by checking the
audio_component field in the assigned hdac_bus.

One caveat is that PCH for Haswell and Broadwell must not be bound
with i915 audio component, as there are dedicated HD-audio HDMI
controllers on these platforms.  Ditto for Poulsbo and Oaktrail as
they use gma500 graphics, not i915.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add HD Audio Device PCI ID for the Intel Broxton platform.
It is an HDA Intel PCH controller.
Signed-off-by: NLu, Han <han.lu@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Adding Intel codename Lewisburg platform device IDs for audio.

[rearranged the position by tiwai]
Signed-off-by: NAlexandra Yates <alexandra.yates@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

We've had many reports that some Creative sound cards with CA0132
don't work well.  Some reported that it starts working after reloading
the module, while some reported it starts working when a 32bit kernel
is used.  All these facts seem implying that the chip fails to
communicate when the buffer is located in 64bit address.

This patch addresses these issues by just adding AZX_DCAPS_NO_64BIT
flag to the corresponding PCI entries.  I casually had a chance to
test an SB Recon3D board, and indeed this seems helping.

Although this hasn't been tested on all Creative devices, it's safer
to assume that this restriction applies to the rest of them, too.  So
the flag is applied to all Creative entries.

Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Currently everyone and their dog has their own favourite spelling
for vga_switcheroo. This makes it hard to grep dmesg for log entries
relating to vga_switcheroo. It also makes it hard to find related
source files in the tree.

vga_switcheroo.c uses pr_fmt "vga_switcheroo". Use that everywhere.
Signed-off-by: NLukas Wunner <lukas@wunner.de>
Reviewed-by: NTakashi Iwai <tiwai@suse.de>
Link: http://patchwork.freedesktop.org/patch/msgid/9b0175319ce78d831acfcf11e4c6c760f826b0e3.1444663039.git.lukas@wunner.deSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The active attribute in struct vga_switcheroo_client denotes whether
the outputs are currently switched to this client. The attribute is
only meaningful for vga clients. It is never used for audio clients.

The function vga_switcheroo_register_audio_client() misuses this
attribute to store whether the audio device is fully initialized.
Most likely there was a misunderstanding about the meaning of
"active" when this was added.

Comment from Takashi's review:

"Not really.  The full initialization of audio was meant that the audio
is active indeed.  Admittedly, though, the active flag for each audio
client doesn't play any role because the audio always follows the gfx
state changes, and the value passed there doesn't reflect the actual
state due to the later change.  So, I agree with the removal of the
flag itself -- or let the audio active flag following the
corresponding gfx flag.  The latter will make the proc output more
consistent while the former is certainly more reduction of code."

Set the active attribute to false for audio clients. Remove the
active parameter from vga_switcheroo_register_audio_client() and
its sole caller, hda_intel.c:register_vga_switcheroo().

vga_switcheroo_register_audio_client() was introduced by 3e9e63db
("vga_switcheroo: Add the support for audio clients"). Its use in
hda_intel.c was introduced by a82d51ed ("ALSA: hda - Support
VGA-switcheroo").

v1.1: The changes above imply that in find_active_client() the call
to client_is_vga() is now superfluous. Drop it.

Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: NLukas Wunner <lukas@wunner.de>
[danvet: Add Takashi's clarification to the commit message.]
Reviewed-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

PM ops could be triggered before HDA is done initializing
and cause PM to set HDA controller to D3Hot.  This can result
in "CORB reset timeout#2, CORBRP = 65535" and "no codecs
initialized".  Additionally, PM ops can be triggered before
azx_probe_continue finishes (async probe).  This can result
in a NULL deref kernel crash.

To fix this, avoid PM ops if !chip->running.
Signed-off-by: NU. Artie Eoff <ullysses.a.eoff@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fixes audio problems on newer asics
Signed-off-by: NMaruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When the controller is powered up but the HDMI codec is powered down
on Skylake, the power well is turned off. When the codec is then
powered up again, we need to poke the codec a little extra to make
sure it wakes up. Otherwise we'll get sad "no response from codec"
messages and broken audio.

This also changes azx_runtime_resume to actually call
snd_hdac_set_codec_wakeup for Skylake (before STATETS read).
(Otherwise it would only have been called for Haswell and Broadwell,
which both do not need it, so this probably was not the author's
intention.)
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Reviewed-by: NLibin Yang <libin.yang@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fixes audio problems on newer asics.

Noticed by: Kelly Anderson <kelly@xilka.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When CONFIG_SND_HDA_I915=n, we get a compile warning:
  sound/pci/hda/hda_intel.c: In function ‘azx_probe_continue’:
  sound/pci/hda/hda_intel.c:1882:2: warning: label ‘skip_i915’ defined but not used [-Wunused-label]

Fix it by putting again ifdef to it.  Sigh.

Fixes: bf06848b ('ALSA: hda - Continue probing even if i915 binding fails')
Reported-by: NBorislav Petkov <bp@suse.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The previous patch tried to continue the probe if i915 binding fails.
For for simplicity reason, we haven't implemented abort even for
controller chips that are dedicated for HDMI/DP on HSW and BDW.
However, Mengdong suggested that this can be dangerous; BIOS may
disable gfx power well although the PCI entry for HD-audio is left,
and this may result in the unexpected behavior, kernel errors, etc.

For avoiding this situation, abort the probe at i915 binding failure
only for HSW/BDW chips selectively.  For other chips, it still
continues.

Fixes: bf06848b ('ALSA: hda - Continue probing even if i915 binding fails')
Reported-by: NMengdong Lin <mengdong.lin@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Currently snd-hda-intel driver aborts the probing of Intel HD-audio
controller with i915 power well management when binding with i915
driver via hda_i915_init() fails.  This is no big problem for Haswell
and Broadwell where the HD-audio controllers are dedicated to
HDMI/DP, thus i915 link is mandatory.  However, Skylake, Baytrail and
Braswell have only one controller and both HDMI/DP and analog codecs
share the same bus.  Thus, even if HDMI/DP isn't usable, we should
keep the controller working for other codecs.

For fixing this, this patch simply allows continuing the probing even
if hda_i915_init() call fails.  This may leave stale sound components
for HDMI/DP devices that are unbound with graphics.  We could abort
the probing selectively, but from the code simplicity POV, it's better
to continue in all cases.
Reported-by: NLibin Yang <libin.yang@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>