- 11 10月, 2013 11 次提交
-
-
由 Gabor Juhos 提交于
Update the rt2800_get_default_vgc function to use the same VGC values that the DPO_RT5572_LinuxSTA_2.6.1.3_20121022 reference driver uses. References: RT35xx_ChipAGCAdjust in chips/rt35xx.c RT3593_R66_MID_LOW_SENS_GET macro in include/chip/rt3593.h RT3593_R66_NON_MID_LOW_SEMS_GET macro in include/chips/rt3593.h Signed-off-by: NGabor Juhos <juhosg@openwrt.org> Acked-by: NStanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Gabor Juhos 提交于
The TXPOWER_DELTA field of the regular EEPROM stores the TX power compensation value for HT40. The extended EEPROM has no such field, it stores separate TX power values for HT20 and for HT40. Signed-off-by: NGabor Juhos <juhosg@openwrt.org> Acked-by: NPaul Menzel <paulepanter@users.sourceforge.net> Acked-by: NStanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Gabor Juhos 提交于
The comments are indicating that the TXMIXER_GAIN_BG and TXMIXED_GAIN_A entries are overlapping with the RSSI_BG2 and RSSI_A2 entries in the extended EEPROM map. This is not correct, because the upper byte of the RSSI_BG2 and RSSI_A2 entries are reserved. There are no TX mixer gain values are stored at all in the extended EEPROM. Remove the initialization of these entries from the extended EEPROM map to reflect this. Signed-off-by: NGabor Juhos <juhosg@openwrt.org> Acked-by: NPaul Menzel <paulepanter@users.sourceforge.net> Acked-by: NStanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
There are some BCM4313 out there with a PCI id of 0x4313. These devices are missing a sprom and are only used on routers or other embedded devices. We found one connected to a BCM63XX SoC. This devices was found by someone in this ticket: https://dev.openwrt.org/ticket/13551Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
This PCI id is used by some BCM4313 cards without a sprom. I have seen such a card on a router connected to some BCM63XX SoC via PCIe. There are cards out there with the same PCI id and a BCM4311, which is a pre ieee80211n chip only supporting ieee80211a, these are still not supported by b43 and not detected by ssb. This devices was found by someone in this ticket: https://dev.openwrt.org/ticket/13551Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
bcma currently only supports PCIe cards and no PCI cards, reject them if we find them. I have never heard of any PCI card using the AI bus (bcma), all of them are using ssb instead. Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Felipe Balbi 提交于
TI firmwares are located under ti-connectivity directory. Update path to make sure driver can find and load firmware blob. Signed-off-by: NFelipe Balbi <balbi@ti.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Kirill Tkhai 提交于
Currently driver name is wrong. PCI device address is visible at /proc/interrupts instead of the name: 43: 124 0 0 0 PCI-MSI-edge rtsx_pci 44: 384 0 0 0 PCI-MSI-edge snd_hda_intel 45: 25096 0 0 0 PCI-MSI-edge 0000:01:00.0 ^^^^^^^^^^^^ So, pass the right name. rt2x00_ops->name contains KBUILD_MODNAME and good for that, so pass it. Handler names will be "rt2500pci", "rt2500pci" etc. Signed-off-by: NKirill Tkhai <tkhai@yandex.ru> CC: Ivo van Doorn <IvDoorn@gmail.com> CC: Gertjan van Wingerde <gwingerde@gmail.com> CC: Helmut Schaa <helmut.schaa@googlemail.com> CC: linux-wireless@vger.kernel.org Acked-by: NStanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Eugene Krasnikov 提交于
This is a mac80211 driver for Qualcomm WCN3660/WCN3680 devices. So far WCN3660/WCN3680 is available only on MSM platform. Firmware can be found here: https://www.codeaurora.org/cgit/external/hisense/platform/vendor/qcom-opensource/wlan/prima/tree/firmware_bin?h=8130_CS Wiki page is available here: http://wireless.kernel.org/en/users/Drivers/wcn36xx A lot people made a contribution to this driver. Here is the list in alphabetical order: Eugene Krasnikov <k.eugene.e@gmail.com> Kalle Valo <kvalo@qca.qualcomm.com> Olof Johansson <dev@skyshaper.net> Pontus Fuchs <pontus.fuchs@gmail.com> Yanbo Li <yanbol@qti.qualcomm.com> Signed-off-by: NEugene Krasnikov <k.eugene.e@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Peter Senna Tschudin 提交于
The variables cancel_scan_cmd, enable_data, hs_activate and valid are only assigned the values true and false. Change its type to bool. The simplified semantic patch that find this problem is as follows (http://coccinelle.lip6.fr/): @exists@ type T; identifier b; @@ - T + bool b = ...; ... when any b = \(true\|false\) Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com> Acked-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 04 10月, 2013 27 次提交
-
-
由 Xose Vazquez Perez 提交于
0411,0241 RT5572 BUFFALO WI-U2-300D Wireless LAN Adapter 0789,0170 RT3572 Logitec LAN-W300AN/U2 0846,9013 RT3573 NETGEAR Adaptador USB Inalambrico Movistar 0df6,006e RT3573 Sitecom WiFi USB adapter N900 2001,3c1f RT3573 D-Link DWA-162 Wireless N900 Dual Band Adapter 2001,3c20 RT5372 D-Link DWA-140 Wireless N USB Adapter(rev.D) 2001,3c21 RT5572 D-Link DWA-160 Xtreme N Dual Band USB Adapter(rev.C) 2001,3c22 RT5372 D-Link DWA-132 Wireless N USB Adapter(rev.B) 2001,3c23 RT5372 D-Link GO-USB-N300 Wireless N Easy USB Adapter 2019,ab29 ? Planex GW-USMirco300 20f4,724a RT5572 TRENDnet N600 Wireless Dual Band USB Adapter Cc: Ivo van Doorn <IvDoorn@gmail.com> Cc: Gertjan van Wingerde <gwingerde@gmail.com> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Cc: John W. Linville <linville@tuxdriver.com> Cc: users@rt2x00.serialmonkey.com Cc: linux-wireless@vger.kernel.org Signed-off-by: NXose Vazquez Perez <xose.vazquez@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Larry Finger 提交于
Now that rtl_phy_scan_operation_backup() exists, convert rtl8188ee to use it. Routine rtl88e_phy_scan_operation_backup() is no longer used and is removed. Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Larry Finger 提交于
Now that rtl_phy_scan_operation_backup() exists, convert rtl8723ae to use it. Routine rtl8723ae_phy_scan_operation_backup() is no longer used and is removed. Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Larry Finger 提交于
Now that rtl_phy_scan_operation_backup() exists, convert rtl8192de to use it. Routine rtl92d_phy_scan_operation_backup() is no longer used and is removed. Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Larry Finger 提交于
Drivers rtl8192ce and rtl8192cu no longer rely on this routine. It is removed. Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Larry Finger 提交于
Now that rtl_phy_scan_operation_backup() exists, convert rtl8192ce to use it. Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Larry Finger 提交于
Now that the routine exists in driver rtlwifi, convert rtl8192cu to use it. Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Larry Finger 提交于
Several of the drivers supported by rtlwifi individually implement the same routine that supports scans. As a first step, create this routine in driver rtlwifi. Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Larry Finger 提交于
This completes removal of all places that reference variable 'noise' in the rtl_stats struct. The definition of the struct is unchanged. Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Larry Finger 提交于
Smatch lists the following: CHECK drivers/net/wireless/rtlwifi/rtl8188ee/hw.c drivers/net/wireless/rtlwifi/rtl8188ee/hw.c:149 _rtl88ee_set_fw_clock_on() info: ignoring unreachable code. drivers/net/wireless/rtlwifi/rtl8188ee/hw.c:149 _rtl88ee_set_fw_clock_on() info: ignoring unreachable code. This info message is the result of a real error due to a missing break statement in a "while (1)" loop. Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> [3.10+] Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Larry Finger 提交于
Smatch displays the following: CHECK drivers/net/wireless/rtlwifi/usb.c drivers/net/wireless/rtlwifi/usb.c:458 _rtl_usb_rx_process_agg() warn: assigning (-98) to unsigned variable 'stats.noise' drivers/net/wireless/rtlwifi/usb.c:503 _rtl_usb_rx_process_noagg() warn: assigning (-98) to unsigned variable 'stats.noise' drivers/net/wireless/rtlwifi/usb.c:596 _rtl_rx_get_padding() info: ignoring unreachable code. drivers/net/wireless/rtlwifi/usb.c:596 _rtl_rx_get_padding() info: ignoring unreachable code. The variable 'stats.noise' is not used, thus the initializers are removed. The unreachable code info is fixed by including the appropriate section inside #ifdef .. #endif constructions. Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Larry Finger 提交于
Smatch reports the following: CHECK drivers/net/wireless/rtlwifi/pci.c drivers/net/wireless/rtlwifi/pci.c:739 _rtl_pci_rx_interrupt() warn: assigning (-98) to unsigned variable 'stats.noise' The variable 'stats.noise' is not used. That initializer is removed. Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Larry Finger 提交于
Smatch lists the following: CHECK drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:551 rtl92c_dm_pwdb_monitor() info: ignoring unreachable code. drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:551 rtl92c_dm_pwdb_monitor() info: ignoring unreachable code. drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:870 rtl92c_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'txpwr_level' 2 <= 2 drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:870 rtl92c_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'txpwr_level' 2 <= 2 drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:882 rtl92c_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'txpwr_level' 2 <= 2 drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:883 rtl92c_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'txpwr_level' 2 <= 2 drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:891 rtl92c_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'txpwr_level' 2 <= 2 drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:892 rtl92c_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'txpwr_level' 2 <= 2 The unreachable code message is fixed by deleting the code that follows a return. The errors are fixed by increasing the size of txpwr_level. Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Larry Finger 提交于
Smatch lists the following: CHECK drivers/net/wireless/rtlwifi/rtl8192cu/trx.c drivers/net/wireless/rtlwifi/rtl8192cu/trx.c:367 _rtl_rx_process() warn: assigning (-98) to unsigned variable 'stats.noise' This variable is unused, thus the initializer is removed, as well as a comment referring to that variable. Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Larry Finger 提交于
Smatch lists the following: CHECK drivers/net/wireless/rtlwifi/rtl8192de/hw.c drivers/net/wireless/rtlwifi/rtl8192de/hw.c:1200 rtl92de_set_qos() info: ignoring unreachable code. drivers/net/wireless/rtlwifi/rtl8192de/hw.c:1200 rtl92de_set_qos() info: ignoring unreachable code. The dead code is deleted. Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Larry Finger 提交于
Smatch lists the following: CHECK drivers/net/wireless/rtlwifi/rtl8192de/dm.c drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1054 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'ofdm_index' 2 <= 2 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1056 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'ofdm_index' 2 <= 2 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1126 rtl92d_dm_txpower_tracking_callback_thermalmeter() debug: remove_pools: nr_children over 4000 (4596). (rtlpriv->dbg.global_debuglevel merged) drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1126 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1129 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1132 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1135 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1138 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1141 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1144 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1147 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1151 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1154 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1157 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1160 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1163 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1166 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1169 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1172 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255 This patch fixes several off-by-one errors. It also removes a comment referencing variable 'noise' in the rts_stats struct. Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
Add support for new RF chip ID: 3070. It seems to be the same as 5370, maybe vendor just put wrong value on the eeprom, but add this id anyway since devices with it showed on the marked. Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Arend van Spriel 提交于
The brcmfmac has common and bus specific part. The rx function api was using sk_buff_head. Changed to sk_buff instead. Reviewed-by: NHante Meuleman <meuleman@broadcom.com> Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hante Meuleman 提交于
SDIO firmware download routines uses one name for firmware file and nvram file for all sdio devices. This is not user friendly. Use fw filename and nvram filename based upon chip id and revision. Reported-by: NStephen Warren <swarren@wwwdotorg.org> Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: NHante Meuleman <meuleman@broadcom.com> Signed-off-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Arend van Spriel 提交于
The definition of BRCMF_EVENTING_MASK_LEN results in a sparse error message .../fweh.c:331:22: error: bad constant expression .../fweh.c:388:22: error: bad constant expression .../dhd_common.c:256:22: error: bad constant expression This is caused by the use of roundup() in BRCMF_EVENTING_MASK_LEN and it is used to allocate an array variable on the stack. Better use DIV_ROUND_UP() macro. Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: NHante Meuleman <meuleman@broadcom.com> Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Franky Lin 提交于
Bus layer need to share sk_buff::cb with firmware signal feature. Reserve necessary memory so they won't overwrite each other. Reviewed-by: NArend Van Spriel <arend@broadcom.com> Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: NFranky Lin <frankyl@broadcom.com> Signed-off-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Franky Lin 提交于
Perform a valid check for core index to avoid illegal address access. Reviewed-by: NHante Meuleman <meuleman@broadcom.com> Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NFranky Lin <frankyl@broadcom.com> Signed-off-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Franky Lin 提交于
BCM4339 is an a/b/g/n/ac 1x1 WiFi chip. This patch adds support for it through SDIO interface. Reviewed-by: NHante Meuleman <meuleman@broadcom.com> Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NFranky Lin <frankyl@broadcom.com> Signed-off-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Franky Lin 提交于
Update event list to keep sync with firmware development. Use calculated event mask length instead of hard-coded value. Reviewed-by: NArend Van Spriel <arend@broadcom.com> Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: NFranky Lin <frankyl@broadcom.com> Signed-off-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 John W. Linville 提交于
Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
-
-
- 03 10月, 2013 2 次提交
-
-
由 Marcel Holtmann 提交于
The Bluetooth specification makes it clear that only one command should be present in the L2CAP LE signalling packet. So tighten the checks here and restrict it to exactly one command. This is different from L2CAP BR/EDR signalling where multiple commands can be part of the same packet. Signed-off-by: NMarcel Holtmann <marcel@holtmann.org> Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
-
由 Marcel Holtmann 提交于
When SMP packets are received, make sure they contain at least 1 byte header for the opcode. If not, drop the packet and disconnect the link. Signed-off-by: NMarcel Holtmann <marcel@holtmann.org> Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
-