Pull sparc fix from David Miller:
 "Brown paper bag fix for sparc64"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Fix missing put_cpu_var() in tlb_batch_add_one() when not batching.

Pull gpi fix from Linus Walleij:
 "This is a last minute revert for the GPIO tree, as Mike Dunn noticed
  breakage on some older PXA machines due to moving PXA GPIO initcalls
  to the module_init initlevel"

* tag 'gpio-v3.9-lastminute' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  Revert "gpio: pxa: set initcall level to module init"

Reported-by: NMeelis Roos <mroos@linux.ee>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 6c7e660a.

The commit causes breakage on several older PXA machines.
Reported-by: NMike Dunn <mikedunn@newsguy.com>
Acked-by: NHaojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Pull MIPS fix from Ralf Baechle:
 "Revert the change of the definition of PAGE_MASK which was prettier
  but broke a few relativly rare platforms"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  Revert "MIPS: page.h: Provide more readable definition for PAGE_MASK."

This reverts commit c17a6554.

Manuel Lauss writes:

lmo commit c17a6554 (MIPS: page.h: Provide more readable definition for
PAGE_MASK) apparently breaks ioremap of 36-bit addresses on my Alchemy
systems (PCI and PCMCIA) The reason is that in arch/mips/mm/ioremap.c
line 157  (phys_addr &= PAGE_MASK) bits 32-35 are cut off.  Seems the
new PAGE_MASK is explicitly 32bit, or one could make it signed instead
of unsigned long.

Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull crypto fix from Herbert Xu:
 "This fixes a kernel memory leak in the algif interface"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: algif - suppress sending source address information in recvmsg

Pull perf fixes from Ingo Molnar:
 "Misc fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86: Fix offcore_rsp valid mask for SNB/IVB
  perf: Treat attr.config as u64 in perf_swevent_init()

I'm going to do an -rc8, so I'm just going to do this rather than delay
it any further. They are arguably stable material anyway.

* vm_ioremap_memory-examples:
  mtdchar: remove no-longer-used vma helpers
  vm: convert snd_pcm_lib_mmap_iomem() to vm_iomap_memory() helper
  vm: convert fb_mmap to vm_iomap_memory() helper
  vm: convert mtdchar mmap to vm_iomap_memory() helper
  vm: convert HPET mmap to vm_iomap_memory() helper

Pull kdump fixes from Peter Anvin:
 "The kexec/kdump people have found several problems with the support
  for loading over 4 GiB that was introduced in this merge cycle.  This
  is partly due to a number of design problems inherent in the way the
  various pieces of kdump fit together (it is pretty horrifically manual
  in many places.)

  After a *lot* of iterations this is the patchset that was agreed upon,
  but of course it is now very late in the cycle.  However, because it
  changes both the syntax and semantics of the crashkernel option, it
  would be desirable to avoid a stable release with the broken
  interfaces."

I'm not happy with the timing, since originally the plan was to release
the final 3.9 tomorrow.  But apparently I'm doing an -rc8 instead...

* 'x86-kdump-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  kexec: use Crash kernel for Crash kernel low
  x86, kdump: Change crashkernel_high/low= to crashkernel=,high/low
  x86, kdump: Retore crashkernel= to allocate under 896M
  x86, kdump: Set crashkernel_low automatically

Pull x86 fixes from Peter Anvin:
 "Three groups of fixes:

   1. Make sure we don't execute the early microcode patching if family
      < 6, since it would touch MSRs which don't exist on those
      families, causing crashes.

   2. The Xen partial emulation of HyperV can be dealt with more
      gracefully than just disabling the driver.

   3. More EFI variable space magic.  In particular, variables hidden
      from runtime code need to be taken into account too."

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, microcode: Verify the family before dispatching microcode patching
  x86, hyperv: Handle Xen emulation of Hyper-V more gracefully
  x86,efi: Implement efi_no_storage_paranoia parameter
  efi: Export efi_query_variable_store() for efivars.ko
  x86/Kconfig: Make EFI select UCS2_STRING
  efi: Distinguish between "remaining space" and actually used space
  efi: Pass boot services variable info to runtime code
  Move utf16 functions to kernel core and rename
  x86,efi: Check max_size only if it is non-zero.
  x86, efivars: firmware bug workarounds should be in platform code

Pull ARM fixes from Russell King:
 "A set of fixes from various people - Will Deacon gets a prize for
  removing code this time around.  The biggest fix in this lot is
  sorting out the ARM740T mess.  The rest are relatively small fixes."

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: 7699/1: sched_clock: Add more notrace to prevent recursion
  ARM: 7698/1: perf: fix group validation when using enable_on_exec
  ARM: 7697/1: hw_breakpoint: do not use __cpuinitdata for dbg_cpu_pm_nb
  ARM: 7696/1: Fix kexec by setting outer_cache.inv_all for Feroceon
  ARM: 7694/1: ARM, TCM: initialize TCM in paging_init(), instead of setup_arch()
  ARM: 7692/1: iop3xx: move IOP3XX_PERIPHERAL_VIRT_BASE
  ARM: modules: don't export cpu_set_pte_ext when !MMU
  ARM: mm: remove broken condition check for v4 flushing
  ARM: mm: fix numerous hideous errors in proc-arm740.S
  ARM: cache: remove ARMv3 support code
  ARM: tlbflush: remove ARMv3 support

Pull sparc fixes from David Miller:

 1) Fix race in sparc64 TLB shootdowns, we have to synchronize with the
    sibling cpus completing if we are passing them a reference via
    pointer to a data structure.

 2) Fix cleaning of bitmaps in sparc32, from Akinobu Mita.

 3) Fix various sparc header mistakes, some of which resulted in
    userland build breakage.  From Sam Ravnborg.

 4) Kill ghost declarations and defines missed when several bits of code
    got deleted recently.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Fix race in TLB batch processing.
  sparc: use asm-generic version of types.h
  bbc_i2c: fix section mismatch warning
  sparc: use generic headers
  sparc:cleanup unused code in smp_32.h
  sparc/iommu: fix typo s/265KB/256KB/
  sparc/srmmu: clear trailing edge of bitmap properly
  sparc:remove unused declaration smp_boot_cpus()

Pull networking updates from David Miller:

 1) ax88796 does 64-bit divides which causes link errors on ARM, fix
    from Arnd Bergmann.

 2) Once an improper offload setting is detected on an SKB we don't rate
    limit the log message so we can very easily live lock.  From Ben
    Greear.

 3) Openvswitch cannot report vport configuration changes reliably
    because it didn't preallocate the netlink notification message
    before changing state.  From Jesse Gross.

 4) The effective UID/GID SCM credentials fix, from Linus.

 5) When a user explicitly asks for wireless authentication, cfg80211
    isn't told about the AP detachment leaving inconsistent state.  Fix
    from Johannes Berg.

 6) Fix self-MAC checks in batman-adv on multi-mesh nodes, from Antonio
    Quartulli.

 7) Revert build_skb() change sin IGB driver, can result in memory
    corruption.  From Alexander Duyck.

 8) Fix setting VLANs on virtual functions in IXGBE, from Greg Rose.

 9) Fix TSO races in qlcnic driver, from Sritej Velaga.

10) In bnx2x the kernel driver and UNDI firmware can try to program the
    chip at the same time, resulting in corruption.  Add proper
    synchronization.  From Dmitry Kravkov.

11) Fix corruption of status block in firmware ram in bxn2x, from Ariel
    Elior.

12) Fix load balancing hash regression of bonding driver in forwarding
    configurations, from Eric Dumazet.

13) Fix TS ECR regression in TCP by calling tcp_replace_ts_recent() in
    all the right spots, from Eric Dumazet.

14) Fix several bonding bugs having to do with address manintainence,
    including not removing address when configuration operations
    encounter errors, missed locking on the address lists, missing
    refcounting on VLAN objects, etc.  All from Nikolay Aleksandrov.

15) Add workarounds for firmware bugs in LTE qmi_wwan devices, wherein
    the devices fail to add a proper ethernet header while on LTE
    networks but otherwise properly do so on 2G and 3G ones.  From Bjørn
    Mork.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
  net: fix incorrect credentials passing
  net: rate-limit warn-bad-offload splats.
  net: ax88796: avoid 64 bit arithmetic
  qlge: Update version to 1.00.00.32.
  qlge: Fix ethtool autoneg advertising.
  qlge: Fix receive path to drop error frames
  net: qmi_wwan: prevent duplicate mac address on link (firmware bug workaround)
  net: qmi_wwan: fixup destination address (firmware bug workaround)
  net: qmi_wwan: fixup missing ethernet header (firmware bug workaround)
  bonding: in bond_mc_swap() bond's mc addr list is walked without lock
  bonding: disable netpoll on enslave failure
  bonding: primary_slave & curr_active_slave are not cleaned on enslave failure
  bonding: vlans don't get deleted on enslave failure
  bonding: mc addresses don't get deleted on enslave failure
  pkt_sched: fix error return code in fw_change_attrs()
  irda: small read past the end of array in debug code
  tcp: call tcp_replace_ts_recent() from tcp_ack()
  netfilter: xt_rpfilter: skip locally generated broadcast/multicast, too
  netfilter: ipset: bitmap:ip,mac: fix listing with timeout
  bonding: fix l23 and l34 load balancing in forwarding path
  ...

Commit 257b5358 ("scm: Capture the full credentials of the scm
sender") changed the credentials passing code to pass in the effective
uid/gid instead of the real uid/gid.

Obviously this doesn't matter most of the time (since normally they are
the same), but it results in differences for suid binaries when the wrong
uid/gid ends up being used.

This just undoes that (presumably unintentional) part of the commit.
Reported-by: NAndy Lutomirski <luto@amacapital.net>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Serge E. Hallyn <serge@hallyn.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: stable@vger.kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Acked-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Matt Fleming (1):
      x86, efivars: firmware bug workarounds should be in platform
      code

Matthew Garrett (3):
      Move utf16 functions to kernel core and rename
      efi: Pass boot services variable info to runtime code
      efi: Distinguish between "remaining space" and actually used
      space

Richard Weinberger (2):
      x86,efi: Check max_size only if it is non-zero.
      x86,efi: Implement efi_no_storage_paranoia parameter

Sergey Vlasov (2):
      x86/Kconfig: Make EFI select UCS2_STRING
      efi: Export efi_query_variable_store() for efivars.ko
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

For each CPU vendor that implements CPU microcode patching, there will
be a minimum family for which this is implemented.  Verify this
minimum level of support.

This can be done in the dispatch function or early in the application
functions.  Doing the latter turned out to be somewhat awkward because
of the ineviable split between the BSP and the AP paths, and rather
than pushing deep into the application functions, do this in
the dispatch function.
Reported-by: N"Bryan O'Donoghue" <bryan.odonoghue.lkml@nexus-software.ie>
Suggested-by: NBorislav Petkov <bp@alien8.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Link: http://lkml.kernel.org/r/1366392183-4149-1-git-send-email-bryan.odonoghue.lkml@nexus-software.ie

If one does do something unfortunate and allow a
bad offload bug into the kernel, this the
skb_warn_bad_offload can effectively live-lock the
system, filling the logs with the same error over
and over.

Add rate limitation to this so that box remains otherwise
functional in this case.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When building ax88796 on an ARM platform with 64-bit resource_size_t,
we currently get

drivers/net/ethernet/8390/ax88796.c:875: undefined reference to `__aeabi_uldivmod'

because we do a division on the length of the MMIO resource.
Since we know that this resource is very short, using an
"unsigned long" instead of "resource_size_t" is entirely
sufficient, and avoids this link-time error.

Cc: Ben Dooks <ben-linux@fluff.org>
Cc: netdev@vger.kernel.org
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Autoneg is supported on specific port types only. Fix the driver to advertise
autoneg based on the port type.
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Fix the driver to drop error frames in the receive path
o Update error counter which was not getting incremented
Signed-off-by: NSritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bjørn Mork says:

====================
This series adds workarounds for 3 different firmware bugs, each
preventing the affected devices from working at all. I therefore
humbly request that these fixes go to stable-3.8 (if still
maintained) and 3.9 (either via net if still possible, or via
stable if not).

All 3 workarounds are applied to all devices supported by the driver.
Adding quirks for specific devices was considered as an alternative,
but was rejected because we have too little information about the
exact distribution of the buggy firmwares. All we know is that the
same bug shows up in devices from at least 3 different, and presumably
independent, vendors.

The workarounds have instead been designed to automatically apply
when necessary, and to have as little impact as possible on unaffected
devices.  The series has been tested on a number of devices both with
and without these bugs.

The series should apply cleanly to net/master, net-next/master and
stable/linux-3.8.y
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We normally trust and use the CDC functional descriptors provided by a
number of devices.  But some of these will erroneously list the address
reserved for the device end of the link.  Attempting to use this on
both the device and host side will naturally not work.

Work around this bug by ignoring the functional descriptor and assign a
random address instead in this case.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Received packets are sometimes addressed to 00:a0:c6:00:00:00
instead of the address the device firmware should have learned
from the host:

321.224126 77.16.85.204 -> 148.122.171.134 ICMP 98 Echo (ping) request  id=0x4025, seq=64/16384, ttl=64

0000  82 c0 82 c9 f1 67 82 c0 82 c9 f1 67 08 00 45 00   .....g.....g..E.
0010  00 54 00 00 40 00 40 01 57 cc 4d 10 55 cc 94 7a   .T..@.@.W.M.U..z
0020  ab 86 08 00 62 fc 40 25 00 40 b2 bc 6e 51 00 00   ....b.@%.@..nQ..
0030  00 00 6b bd 09 00 00 00 00 00 10 11 12 13 14 15   ..k.............
0040  16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25   .......... !"#$%
0050  26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35   &'()*+,-./012345
0060  36 37                                             67

321.240607 148.122.171.134 -> 77.16.85.204 ICMP 98 Echo (ping) reply    id=0x4025, seq=64/16384, ttl=55

0000  00 a0 c6 00 00 00 02 50 f3 00 00 00 08 00 45 00   .......P......E.
0010  00 54 00 56 00 00 37 01 a0 76 94 7a ab 86 4d 10   .T.V..7..v.z..M.
0020  55 cc 00 00 6a fc 40 25 00 40 b2 bc 6e 51 00 00   U...j.@%.@..nQ..
0030  00 00 6b bd 09 00 00 00 00 00 10 11 12 13 14 15   ..k.............
0040  16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25   .......... !"#$%
0050  26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35   &'()*+,-./012345
0060  36 37                                             67

The bogus address is always the same, and matches the address
suggested by many devices as a default address.  It is likely a
hardcoded firmware default.

The circumstances where this bug has been observed indicates that
the trigger is related to timing or some other factor the host
cannot control. Repeating the exact same configuration sequence
that caused it to trigger once, will not necessarily cause it to
trigger the next time. Reproducing the bug is therefore difficult.
This opens up a possibility that the bug is more common than we can
confirm, because affected devices often will work properly again
after a reset.  A procedure most users are likely to try out before
reporting a bug.

Unconditionally rewriting the destination address if the first digit
of the received packet is 0, is considered an acceptable compromise
since we already have to inspect this digit.  The simplification will
cause unnecessary rewrites if the real address starts with 0, but this
is still better than adding additional tests for this particular case.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A number of LTE devices from different vendors all suffer from the
same firmware bug: Most of the packets received from the device while
it is attached to a LTE network will not have an ethernet header. The
devices work as expected when attached to 2G or 3G networks, sending
an ethernet header with all packets.

This driver is not aware of which network the modem attached to, and
even if it were there are still some packet types which are always
received with the header intact.

All devices supported by this driver have severely limited
networking capabilities:
 - can only transmit IPv4, IPv6 and possibly ARP
 - can only support a single host hardware address at any time
 - will only do point-to-point communcation with the host

Because of this, we are able to reliably identify any bogus raw IP
packets by simply looking at the 4 IP version bits.  All we need to
do is to avoid 4 or 6 in the first digit of the mac address.  This
workaround ensures this, and fix up the received packets as necessary.

Given the distribution of the bug, it is believed that the source is
the chipset vendor.  The devices which are verified to be affected are:
 Huawei E392u-12 (Qualcomm MDM9200)
 Pantech UML290  (Qualcomm MDM9600)
 Novatel USB551L (Qualcomm MDM9600)
 Novatel E362    (Qualcomm MDM9600)

It is believed that the bug depend on firmware revision, which means
that possibly all devices based on the above mentioned chipset may be
affected if we consider all available firmware revisions.

The information about affected devices and versions is likely
incomplete.  As the additional overhead for packets not needing this
fixup is very small, it is considered acceptable to apply the
workaround to all devices handled by this driver.
Reported-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nikolay Aleksandrov says:

====================
This patch-set fixes mainly bugs on enslave failure and one occasion
of a needed locking. The patches are:

	1. On enslave failure mc addresses are not flushed from the slave
	2. On enslave failure vlans are not cleaned up from the slave
	3. On enslave failure the bond's primary and curr_active_slave
	   are not cleaned up (which might result in use of freed memory)
	4. On enslave failure netpoll is not disabled which might result in
	   a memory leak
	5. In bond_mc_swap() the bond's mc addr list is walked without
	   netif_addr_lock, since it can be called without rtnl, add it

v2: patch 01 - fix log message and remove unnecessary code move
====================
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use netif_addr_lock_bh() to acquire the appropriate lock before walking.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

slave_disable_netpoll() is not called upon enslave failure which would
lead to a memory leak. Call slave_disable_netpoll() after err_detach as
that's the first error path after enabling netpoll on that slave.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On enslave failure primary_slave can point to new_slave which is to be
freed, and the same applies to curr_active_slave. So check if this is
the case and clean up properly after err_detach because that's the first
error code path after they're set.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The main problem is with vid refcount which only gets bumped up.
Delete the vlans after err_detach as that's the first error path
after the vlans are added.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add bond_mc_list_flush() after err_detach as that's the first error path
after the addresses are added. The main issue is the mc addresses' refcount
which only gets bumped up.

v2: update log message and don't move code unnecessarily
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to return -EINVAL when tb[TCA_FW_MASK] is set and head->mask != 0xFFFFFFFF
instead of 0 (ifdef CONFIG_NET_CLS_IND and tb[TCA_FW_INDEV]), as done elsewhere
in this function.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "reason" can come from skb->data[] and it hasn't been capped so it
can be from 0-255 instead of just 0-6.  For example in irlmp_state_dtr()
the code does:

	reason = skb->data[3];
	...
	irlmp_disconnect_indication(self, reason, skb);

Also LMREASON has a couple other values which don't have entries in the
irlmp_reasons[] array.  And 0xff is a valid reason as well which means
"unknown".

So far as I can see we don't actually care about "reason" except for in
the debug code.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported by Dave Kleikamp, when we emit cross calls to do batched
TLB flush processing we have a race because we do not synchronize on
the sibling cpus completing the cross call.

So meanwhile the TLB batch can be reset (tb->tlb_nr set to zero, etc.)
and either flushes are missed or flushes will flush the wrong
addresses.

Fix this by using generic infrastructure to synchonize on the
completion of the cross call.

This first required getting the flush_tlb_pending() call out from
switch_to() which operates with locks held and interrupts disabled.
The problem is that smp_call_function_many() cannot be invoked with
IRQs disabled and this is explicitly checked for with WARN_ON_ONCE().

We get the batch processing outside of locked IRQ disabled sections by
using some ideas from the powerpc port. Namely, we only batch inside
of arch_{enter,leave}_lazy_mmu_mode() calls.  If we're not in such a
region, we flush TLBs synchronously.

1) Get rid of xcall_flush_tlb_pending and per-cpu type
   implementations.

2) Do TLB batch cross calls instead via:

	smp_call_function_many()
		tlb_pending_func()
			__flush_tlb_pending()

3) Batch only in lazy mmu sequences:

	a) Add 'active' member to struct tlb_batch
	b) Define __HAVE_ARCH_ENTER_LAZY_MMU_MODE
	c) Set 'active' in arch_enter_lazy_mmu_mode()
	d) Run batch and clear 'active' in arch_leave_lazy_mmu_mode()
	e) Check 'active' in tlb_batch_add_one() and do a synchronous
           flush if it's clear.

4) Add infrastructure for synchronous TLB page flushes.

	a) Implement __flush_tlb_page and per-cpu variants, patch
	   as needed.
	b) Likewise for xcall_flush_tlb_page.
	c) Implement smp_flush_tlb_page() to invoke the cross-call.
	d) Wire up global_flush_tlb_page() to the right routine based
           upon CONFIG_SMP

5) It turns out that singleton batches are very common, 2 out of every
   3 batch flushes have only a single entry in them.

   The batch flush waiting is very expensive, both because of the poll
   on sibling cpu completeion, as well as because passing the tlb batch
   pointer to the sibling cpus invokes a shared memory dereference.

   Therefore, in flush_tlb_pending(), if there is only one entry in
   the batch perform a completely asynchronous global_flush_tlb_page()
   instead.
Reported-by: NDave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NDave Kleikamp <dave.kleikamp@oracle.com>

cyc_to_sched_clock() is called by sched_clock() and cyc_to_ns()
is called by cyc_to_sched_clock(). I suspect that some compilers
inline both of these functions into sched_clock() and so we've
been getting away without having a notrace marking. It seems that
my compiler isn't inlining cyc_to_sched_clock() though, so I'm
hitting a recursion bug when I enable the function graph tracer,
causing my system to crash. Marking these functions notrace fixes
it. Technically cyc_to_ns() doesn't need the notrace because it's
already marked inline, but let's just add it so that if we ever
remove inline from that function it doesn't blow up.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Pull ARM SoC fixes from Olof Johansson:
 "Only one remaining fix for arm-soc platforms at this time, a small
  bugfix for cpu hotplug on highbank platforms that has become much
  easier to hit as of late.

  Details in the patch description, but it's small and well-contained
  and definitely impacts users of the platform, so 3.9 seems
  appropriate."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: highbank: fix cache flush ordering for cpu hotplug

Pablo Neira Ayuso says:

====================
If time allows, please consider pulling the following patchset contains two
late Netfilter fixes, they are:

* Skip broadcast/multicast locally generated traffic in the rpfilter,
  (closes netfilter bugzilla #814), from Florian Westphal.

* Fix missing elements in the listing of ipset bitmap ip,mac set
  type with timeout support enabled, from Jozsef Kadlecsik.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>