Improve readability of the function by adding the break,
there's no functional impact but it's confusing to fall
through.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Coverity points out that checking assoc_data->ie is
completely useless since it's an array in the struct
and can't be NULL - remove the useless checks.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

802.11-2012 13.3.1 implicitly limits the mesh local link
ID range to that of AID, since for mesh PS the local link
ID must be indicated in the TIM IE, which only holds
IEEE80211_MAX_AID bits.

Also the code was allowing a local link ID of 0, but this
is not correct since that TIM bit is used for indicating
buffered mcast frames.

Generate a random, unique, link ID from 1 - 2007, and drop
a modulo conversion for the local link ID, but keep it for
the peer link ID in case he chose something > MAX_AID.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
[fix some indentation, squash llid assignment]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If we store the peer link ID right after initializing a
new neighbor, there is no need to do it later in the
peering FSM.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Said function was removed some time ago.
Signed-off-by: NBob Copeland <bob@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

All other paths return an error code, do the same here.
Signed-off-by: NBob Copeland <bob@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The ignore_plink_timer flag is set when doing mod_timer() if
the timer was not previously active.  This is to avoid executing
the timeout if del_timer() was subsequently called.  However,
del_timer() only happens if we are moving to ESTAB state or
get a close frame while in HOLDING.

We cannot leave HOLDING and re-enter ESTAB unless we receive a
close frame (in which case ignore_plink_timer is already set) or
if the timeout expires, so there actually isn't a case where
this is needed on mod_timer().
Signed-off-by: NBob Copeland <bob@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The matches_local check can just be done when looking at the
individual action types.
Signed-off-by: NBob Copeland <bob@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Use C instead of cpp for type checking.  Also swap the arguments
into the usual sdata -> sta order.
Signed-off-by: NBob Copeland <bob@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The initial frame checks differ depending on whether this is
a new peer or not, but they were all intermixed with sta checks
as necessary.  Group them together so the two cases are clearer.
Signed-off-by: NBob Copeland <bob@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Reject and accepted close events always put the host in the
holding state and compute a reason code based only on the
current state.  Likewise on establish we always do the same
setup.  Put these in functions to save some duplicated code.
Signed-off-by: NBob Copeland <bob@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Rather than unlock at the end of each case, do it once after
all is said and done.
Signed-off-by: NBob Copeland <bob@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Do all frame transfers in one place at the end of the
big switch statements.  sta->plid and sta->reason can
be passed in any case, since they are only used for
the frames that need them.  Remove assignments to locals
for values already stored in the sta structure.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

According to IEEE 802.11-2012 (8.4.2.104), no peering
management element exists with length 7. This code is checking
to see if llid is present to ignore close frames with different
llid, which would be IEs with length 8.
Signed-off-by: NBob Copeland <bob@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The iniator is already available to us, so use it.
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

wiphy_apply_custom_regulatory() implies WIPHY_FLAG_CUSTOM_REGULATORY
but we never enforced it, do that now and warn if the driver
didn't set it. All drivers should be following this today already.

Having WIPHY_FLAG_CUSTOM_REGULATORY does not however mean you will
use wiphy_apply_custom_regulatory() though, you may have your own
_orig value set up tools / helpers. The intel drivers are examples
of this type of driver.
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Check chandef we get in CAC request is usable for CAC.
All channels have to be DFS channels. Allow DFS_USABLE
and DFS_AVAILABLE channels mix. At least one channel
has to be DFS_USABLE (require CAC).
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add helper fuctions for start/end freq.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently, frames that go into the reordering buffer are stored at
index ieee80211_sn_sub(sn, tid_rx->ssn) % tid_rx->buf_size.

The offset calculation to the starting sequence number (SSN) is
useless and just adds overhead so simply use sn % tid_rx->buf_size.

This means the reordering buffer will start to be filled somewhere
in the middle (at SSN % buf_size) and continue to get used from
there, but there's no reason to start from the beginning.
Signed-off-by: NKarl Beldan <karl.beldan@rivierawaves.com>
[rewrite commit message]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

These two flags are used for the same purpose, just
combine them into a no-ir flag to annotate no initiating
radiation is allowed.

Old userspace sending either flag will have it treated as
the no-ir flag. To be considerate to older userspace we
also send both the no-ir flag and the old no-ibss flags.
Newer userspace will have to be aware of older kernels.

Update all places in the tree using these flags with the
following semantic patch:

@@
@@
-NL80211_RRF_PASSIVE_SCAN
+NL80211_RRF_NO_IR
@@
@@
-NL80211_RRF_NO_IBSS
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_PASSIVE_SCAN
+IEEE80211_CHAN_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IBSS
+IEEE80211_CHAN_NO_IR
@@
@@
-NL80211_RRF_NO_IR | NL80211_RRF_NO_IR
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IR | IEEE80211_CHAN_NO_IR
+IEEE80211_CHAN_NO_IR
@@
@@
-(NL80211_RRF_NO_IR)
+NL80211_RRF_NO_IR
@@
@@
-(IEEE80211_CHAN_NO_IR)
+IEEE80211_CHAN_NO_IR

Along with some hand-optimisations in documentation, to
remove duplicates and to fix some indentation.
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
[do all the driver updates in one go]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The nl80211 attribute NL80211_ATTR_CSA_C_OFF_BEACON should be nested
inside NL80211_ATTR_CSA_IES, but commit ee4bc9e7
("nl80211: enable IBSS support for channel switch announcements")
added a check in the outer message attributes.

Fix channel switch calls by removing the erroneus condition.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
[reword commit message]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

CSA completion could call in a driver
bss_info_changed() with a garbled `changed` flag
leading to all sorts of problems.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Trigger the mesh channel switching procedure if the mesh STA
happens to miss the CSA action frame but able to receive the
beacon containing the CSA and MCSP elements from its peer
mesh STAs.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@cozybit.com>
[fix locking in ieee80211_mesh_process_chnswitch()]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Implement the required procedures for mesh channel switching as defined
in the IEEE Std 802.11-2012 section 10.9.8.4.3 and also handle the CSA
and MCSP elements as followed:
 * Add the function for updating the beacon and probe response frames
   with CSA and MCSP elements during the period of switching to the new
   channel. Both CSA and MCSP elements must be included in beacon and
   probe response frames until the intended channel switch time.
 * The ifmsh->csa_settings is set to NULL and the CSA and MCSP elements
   will then be removed from the beacon or probe response frames once the
   new channel is switched to.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Allow the triggering of CSA frame using mesh interface. The
rules are more or less same with IBSS, such as not allowed to
change between the band and channel width has to be same from
the previous mode. Also, move the ieee80211_send_action_csa
to a common space so that it can be re-used by mesh interface.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Process the CSA frame according to the procedures define in IEEE Std
802.11-2012 section 10.9.8.4.3 as follow:
* The mesh channel switch parameters element (MCSP) must be availabe.
* If the MCSP's TTL is 1, drop the frame but still process the CSA.
* If the MCSP's precedence value is less than or equal to the current
  precedence value, drop the frame and do not process the CSA.
* The CSA frame is forwarded after TTL is decremented by 1 and the
  initiator field is set to 0. Transmit restrict field and others
  are maintained as is.
* No beacon or probe response frame are handled here.

Also, introduce the debug message used for mesh CSA purpose.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Refactor the channel switch IE parsing to reduce the number
of function parameters.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This can be used by a driver to prepare skbs for transmission, which were
obtained via functions such as ieee80211_probereq_get or
ieee80211_nullfunc_get.

This is useful for drivers that want to send those frames directly, but
need rate control information to be prepared first.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Drivers can now use this to parse the regulatory request and
be more verbose when needed.
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This patch fixes errors in the mesh powersave logic which
cause that remote peers do not get peer power mode change
notifications and mesh peer service periods (MPSPs) got
stuck.

When closing a peer link, set the (now invalid) peer-specific
power mode to 'unknown'.

Avoid overhead when local power mode is unchanged.

Reliably clear MPSP flags on peering status update.

Avoid MPSP flags getting stuck by not requesting a further
MPSP ownership if we already are an MPSP owner.
Signed-off-by: NMarco Porsch <marco@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

6c17b77b ensures that a device's
mac80211 queues will remain stopped while offchannel. Since the
vif can no longer be offchannel when the queues wake it's not
necessary to check for this before waking its netdev queues.
Signed-off-by: NSeth Forshee <seth.forshee@canonical.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Including ACPI ID for Broadcom GPS receiver BCM4752.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NRhyland Klein <rklein@nvidia.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This will add the relevant values like the gpios and the
type in rfkill_gpio_platform_data to the rfkill_gpio_data
structure. It will allow those values to be easily picked
from DT and ACPI tables later.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NRhyland Klein <rklein@nvidia.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This sets the direction of the gpio once when it's requested,
and uses the spinlock-safe gpio_set_state() to change the
state.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NRhyland Klein <rklein@nvidia.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Use a simple flag to see the state of the clock, and make
the clock available even without a name. Also, get rid of
HAVE_CLK dependency.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NRhyland Klein <rklein@nvidia.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

And remove now unneeded resource freeing.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NRhyland Klein <rklein@nvidia.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>