hostap_cs: Remove irq_list, irq_mask and pcmcia/version.h

Remove irq_list, irq_mask and pcmcia/version.h as suggested in
http://kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.htmlSigned-off-by: NJouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

EXPORT_SYMTAB does nothing. There's no need to define something if it
doesn't have any effect.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NJouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Update hostap_cs to use new PCMCIA event callback registration.
Signed-off-by: NJouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

When leaving S3 state, the AGP bridge may not have all PCI configuration
registers set in the same way as they were at boot.  This should be fixed
by pci_restore_state - however, the APBASE register cannot be set to
conflict with the APSIZE register.  If APSIZE is larger than it was before
suspend, pci_restore_state will not restore APBASE correctly.  The attached
patch adds an extra item to the agp_bridge_data structure and uses it to
store the value of APBASE.  On resume, this is then written after APSIZE
has been set.  This patch only touches the path used for Intel chipsets
without integrated graphics, and may need to be extended to work with the
others.

Without this patch, I get the symptoms described in bug 4921 - APBASE ends
up overlapping various PCI devices, and as a result they fail to work after
resume.
Signed-off-by: NMatthew Garrett <mjg59@srcf.ucam.org>
Acked-by: NDave Jones <davej@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Close a small window where a device may be not operational again after senseid
finished and the "same device" check fails due to dev=0000 by checking for dnv
after stsch() by then setting the device to not operational.  (No need to
check for dnv in ccw_device_handle_oper() again since we don't do stsch() into
the subchannel's schib in the meantime and will get a crw anyway if the device
becomes not oper again).
Signed-off-by: NCornelia Huck <cohuck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Do not use memcpy in fb_pad_aligned_buffer.  It is suboptimal because only
a few bytes are moved at a time.  Replace with a for-loop.
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

>> vesafb: mode is 800x600x16, linelength=1600, pages=16
>> vesafb: scrolling: redraw
>> vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
>> mtrr: type mismatch for fc000000,1000000 old: write-back new: write-
>> combining

Range is already set to write-back, vesafb attempts to add a write-combining
mtrr (default for vesafb).

>> mtrr: size and base must be multiples of 4 kiB

This is a bug, vesafb attempts to add a size < PAGE_SIZE triggering
the messages below.

To eliminate the warning messages, you can add the option mtrr:2 to add a
write-back mtrr for vesafb.  Or just use nomtrr option.

1. Fix algorithm for finding the best power of 2 size with mtrr_add().

2. Add option to choose the mtrr type by extending the mtrr boot option:

   mtrr:n where n

        0 = no mtrr (equivalent to using the nomtrr option)
        1 = uncachable
        2 = write back
        3 = write combining (default)
        4 = write through
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add support for UARTs in MMIO space and clean up a little whitespace.

HP legacy-free ia64 machines need this.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

It seems that I see a bug in hidinput_hid_event.  The check for NULL can never
work, becaue &hidinput->input is nonzero at all times.

Cc: <vojtech@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch does the same swap, i.e. use the ISO macro if (isoc).
Additionally, it fixes the return value - the usb_calc_bus_time function
returns the time in nanoseconds (I didn't notice that before) while the
HS_USECS and HS_USECS_ISO are microseconds.  This fixes the function to
return nanoseconds always, and adjusts ehci-q.c (the only high-speed
caller of the function) to wrap the call in NS_TO_US().
Signed-off-by: NDan Streetman <ddstreet@ieee.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Compare endpoint address to USB_ENDPOINT_DIR_MASK to determine endpoint
direction...

From: "Conger, Chris A." <CHRIS.A.CONGER@saic.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

USB (OHCI) Host driver for S3C2410/S3C2440 based systems
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Gigabyte GN-WLBZ201 wifi usb dongle works very well, using the zd1201
driver. the only missing part is that the corresponding usbid is not
declared. The following patch should fix this.

From: "Mathieu" <matt@minas-morgul.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch enables a support of KYOCERA AH-K3001V, one of the most
popular cell phone in Japan. This device has vendor specific ID but works
with acm driver by adding USB ID. This device already works on
FreeBSD and OS X by native USB ACM driver with USB ID added.

This device is probed as NO_UNION_NORMAL not to hang up when probing.
Signed-off-by: NMasahito Omote <omote@utyuuzin.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

below you will find the forgotten kmalloc check (sorry).
Signed-off-by: NMichael Hund <mhund@ld-didactic.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch handles a rarely-encountered failure mode in usbcore.  It's
legal for device_add to fail (although now it happens even more rarely
than before since failure to bind a driver is no longer fatal).  So when
we destroy the interfaces in a configuration, we shouldn't try to delete
ones which weren't successfully registered.  Also, failure to register an
interface shouldn't be fatal either -- I think; you may disagree about
this part of the patch.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The only uses of both variables were recently removed.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch fixes an information leak in the usbfs snoop facility:
uninitialized data from __get_free_page can be returned to userspace and
written to the system log.  It also improves the snoop output by printing
the wLength value.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

ftdi_sio: Fix timeouts in a couple of usb_control_msg() calls due to
change of units from jiffies to milliseconds in 2.6.12.
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

ftdi_sio: Update RTS and DTR simultaneously, using a single control URB
instead of separate control URBs for RTS and DTR.  Reinhard Bergmann
observed time differences of up to 680 ms with his application on a
2.4.22 kernel when RTS and DTR were updated using separate control
URBs, which is unacceptable.
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The attached patch adds the following new devices to the ftdi_sio driver:

* microHAM USB-Y6 and USB-Y8 devices submitted by Justin Burket (KL1RL).
* Evolution Robotics ER1 Control Module submitted by Shawn M.  Lavelle.
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The setup-bus code doesn't work correctly for configurations
with more than one display adapter in the same PCI domain.
This stuff actually is a leftover of an early 2.4 PCI setup code
and apparently it stopped working after some "bridge_ctl" changes.
So the best thing we can do is just to remove it and rely on the fact
that any firmware *has* to configure VGA port forwarding for the boot
display device properly.

But then we need to ensure that the bus->bridge_ctl will always
contain valid information collected at the probe time, therefore
the following change in pci_scan_bridge() is needed.
Signed-off-by: NIvan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

There are ROMs reporting that their size exceeds their PCI ROM
resource window. This patch returns the minimum of the resource window
size or the size in the ROM.  An example of this breakage is the XGI
Volari Z7.
Signed-off-by: NJon Smirl <jonsmirl@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Patch against 2.6.12 to unhide SMBus on Toshiba Centrino laptops using
Intel 82855PM chipset.  Tested on Toshiba Tecra M2.
Signed-off-by: NDaniele Gaffuri <d.gaffuri@reply.it>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch was sent first time very long time ago,
but magically was disapeared, it probably exists
in your queue, but to be sure, I resend it.
If can not be applied cleanly after your w1 queue is flushed
into upstrem tree, just drop it.
Thanks.

Patch from Michael Farmbauer <michl@baldrian.franken.de>.
Signed-off-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The 24RF08 corruption prevention in the eeprom and max6875 drivers wasn't
complete. For one thing, the additional quick write should happen as soon
as possible and unconditionally, while both drivers had error paths before.
For another, when a given chip is forced, the core does not emit a quick
write, so a second quick write would cause the corruption rather than
prevent it.

I plan to move the corruption prevention in the core in the long run, so
that individual drivers don't have to care anymore. But I need to merge
i2c_probe and i2c_detect before I do (work in progress).
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Two log messages lack their trailing new line in i2c-core. I'd swear I had
fixed them already, but it seems not. Bonus: improved coding style.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

A few i2c drivers were not updated to use time_after() yet.
Signed-off-by: NMarcelo Feitoza Parisi <marcelo@feitoza.com.br>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

A few split string in i2c (and now hwmon) drivers lack a joining space,
causing them to display incorrectly. This trivial patch fixes that up.
Please apply, thanks.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

DS1339 manual, page 6, chapter Date and time operation:
  The DS1339 can be run in either 12-hour or 24-hour mode. Bit 6 of the
  hours register is defined as the 12-hour or 24-hour mode-select bit.
  When high, the 12-hour mode is selected.

Patch below makes ds1337 driver work as documented in manual.
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

I2C-MPC: Restore code removed

A previous patch to remove support for the OCP device model was way
to generious and moved some of the platform device model code, oops.
Signed-off-by: NKumar Gala <kumar.gala@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix a buffer overflow vunerabilty in previous cmap patch
Signed-off-by: NJon Smirl <jonsmirl@gmail.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch is an attempt to fix deadlocks discovered in the core dm.

The problems boil down to md->lock having to be held in too many places, so
I've split it into two: md->suspend_lock and md->io_lock.

suspend_lock is now held throughout dm_suspended() as well as dm_resume()
and dm_swap_table() so that these functions cannot run concurrently:
there's no requirement for that and it added complexity.

DMF_FS_LOCKED becomes redundant: DMF_SUSPENDED provides adequate
protection.
Signed-Off-By: NAlasdair G Kergon <agk@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Avoid another bdget_disk which can deadlock.
Signed-Off-By: NAlasdair G Kergon <agk@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Some code tidy-ups in preparation for the next patches.  Change
dm_table_pre/postsuspend_targets to accept NULL.  Use dm_suspended()
throughout.
Signed-Off-By: NAlasdair G Kergon <agk@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch adds functionality to check the PCI sub-class code of an
AHCI capable device before disabling AHCI.  It fixes a bug where an
ICH7 sata controller is being setup by the BIOS as sub-class 1 (ide)
and the AHCI control registers weren't being initialized, thus causing
an IO error in piix_disable_ahci().
Signed-off-by: NGregory Felix <greg.felix@gmail.com>

* ret has no need to be unsigned in cpufreq_driver_target()
* ret has no need to be initialized in __cpufreq_governor()
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NDave Jones <davej@redhat.com>

If the PCDP supplies parity, use it (only none/even/odd supported), and
don't append parity/stop bit arguments unless baud is present.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

sys_reboot() now calls device_suspend(), so it is no longer necessary for
the e1000 driver to register a reboot notifier [in fact doing so results in
e1000_suspend() getting called twice].

(akpm: we need to fast-track this.  It's causing ia64 to oops on shutdown)
Signed-off-by: NTony Luck <tony.luck@intel.com>
Cc: <cramerj@intel.com>
Cc: <john.ronciak@intel.com>
Cc: <ganesh.venkatesan@intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NIan Campbell <icampbell@arcom.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>