Fix compilation the following compilation warning, which happens when
CONFIG_BT_INTEL is not set:

  drivers/bluetooth/btintel.h:98:13: warning: ‘btintel_version_info’
  defined but not used [-Wunused-function]
   static void btintel_version_info(struct hci_dev *hdev,
                                    struct intel_version *ver)
               ^
Signed-off-by: NVincent Stehlé <vincent.stehle@laposte.net>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

if btmrvl_tx_pkt() is called, and the branch
  if (skb_headroom(skb) < BTM_HEADER_LEN)
evaluates positive, a new skb is allocated via skb_realloc_headroom.

The original skb is stored in a tmp variable, before being free'd.
However on success, the new skb, is not free'd, nor is it
returned to the caller which will then double-free the original skb.

This issue exists from the original driver submission in
 commit: #132ff4e5

If this code path had been alive, it would have been noted from the
double-free causing a panic.

All skb's here should be allocated through bt_skb_alloc which
adds 8 bytes as headroom, which is plenty against the 4 bytes
pushed on by this driver.

This code path is dead, and buggy at the same time, so the cleanest
approach is to remove the affected branch.

Reported by coverity (CID 113422)
Signed-off-by: NKieran Bingham <kieranbingham@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Don't hide this packet size error.
Signed-off-by: NLoic Poulain <loic.poulain@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Implement runtime PM suspend/resume callbacks.
If LPM supported, controller is put into supsend after a delay of
inactivity (1s). Inactivity is based on LPM idle notification and
host TX traffic.
Signed-off-by: NLoic Poulain <loic.poulain@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add PM suspend/resume callbacks which call lpm_suspend/resume.
Add LPM ack in threaded IRQ handler to notify the controller that
resume is complete.
Protect hci_uart against concurrent removing during suspend/resume.
Signed-off-by: NLoic Poulain <loic.poulain@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add LPM PM suspend/resume/host_wake LPM functions.
A LPM transaction is composed with a LPM request and ack/response.
Host can send a LPM suspend/resume request to the controller which
should respond with a LPM ack.
If resume is requested by the controller (irq), host has to send a LPM
ack once resumed.
Signed-off-by: NLoic Poulain <loic.poulain@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Replace BT_ logging calls by the new bt_dev ones.
Signed-off-by: NFrederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Replace spinlock by mutex to be able to use bcm_device_lock in
sleepable context like devm_request_threaded_irq or upcomming PM support.
Signed-off-by: NFrederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Replace the device_intel list spinlock with a mutex.
devm_request_threaded_irq is not atomic and upcomming PM support should
be simpler.
Signed-off-by: NLoic Poulain <loic.poulain@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Replace BT_ logging calls by the new bt_dev ones.
Signed-off-by: NLoic Poulain <loic.poulain@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Enable controller Low-Power-Mode if we have a pdev to manage host
wake-up. Once LPM is enabled, controller notifies its TX status via
a vendor specific packet (tx_idle/tx_active).
tx_active means that there is more data upcoming from controller.
tx_idle means that controller can be put in suspended state.
Signed-off-by: NLoic Poulain <loic.poulain@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

An IRQ can be retrieved from the pdev resources. This irq will be used
in case of LPM suspend mode to wake-up the host and resume the link.
This resource can be declared as a GPIO-Interrupt which requires to be
converted into IRQ.
Signed-off-by: NLoic Poulain <loic.poulain@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Controllers claiming to be CSR with LMP subversion 0x0c5c don't
actually seem to be authentic CSR controllers. They also don't have
their USB bcdDevice value matching the LMP subversion like all other
CSR controllers:

HCI:

> HCI Event: Command Complete (0x0e) plen 12
      Read Local Version Information (0x04|0x0001) ncmd 1
        Status: Success (0x00)
        HCI version: Bluetooth 2.0 (0x03) - Revision 3164 (0x0c5c)
        LMP version: Bluetooth 2.0 (0x03) - Subversion 3164 (0x0c5c)
        Manufacturer: Cambridge Silicon Radio (10)

USB:

T: Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=16 #Cfgs= 1
P: Vendor=0a12 ProdID=0001 Rev= 1.34
C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms

These controllers also have the HCI_Read_Stored_Link_Key command
broken so it's important the right quirk is set for them.
Reported-and-tested-by: NRhobison Alves Pereira <rhobison@hotmail.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

If bcm_suspend is called whithout device opened there is a crash as
it tries to use bdev->hu which is NULL.
Rename bcm_device_list_lock to bcm_device_lock as it does not only apply
to bcm_device_list.
Signed-off-by: NFrederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

A platform device can be used to provide some specific resources in
order to manage the controller. In this first patch we retrieve the
reset gpio which is used to power on/off the controller.

The main issue is to match the current tty with the correct pdev.
In case of ACPI, we can easily find the right tty/pdev pair because
they are both child of the same UART port.

If controller is powered-on from the driver, we need to wait for a
HCI boot event before being able to send any command.
Signed-off-by: NLoic Poulain <loic.poulain@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The iBT 3.0 controllers need intel/ibt-11-5.sfi and intel/ibt-11-5.ddc
firmware files from linux-firmware repository.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Signed-off-by: NMinjune Kim <infinite.minjune.kim@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Implement the set_baudrate callback for hci_intel.
 - Controller requires a read Intel version command before updating
   its baudrate.
 - The operation consists in an async cmd since the controller does
   not respond at the same speed.
 - Wait 100ms to let the controller change its baudrate.
 - Clear RTS until we change our own UART speed

Manage speed change in the setup function, we need to restore the oper
speed once chip has booted on patched firmware.
Signed-off-by: NLoic Poulain <loic.poulain@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Packets with a variable length value equal to zero were not received.

Since no more data expected (and input buffer entirely consumed), we
need to complete/forward the packet immediately instead of waiting for
more data.
Signed-off-by: NLoic Poulain <loic.poulain@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This change ensures we will get driver name as 'btmrvl_sdio'
in udev event.
Signed-off-by: NShengzhen Li <szli@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

We should not sleep while holding a spinlock.
bcm_gpio_set_power is called while holding the bcm_device_list lock.
Signed-off-by: NLoic Poulain <loic.poulain@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch enables quirk handling for Silicon Wave based devices and
fixes kernel bug with id 42985.

T:  Bus=01 Lev=01 Prnt=01 Port=07 Cnt=04 Dev#=  6 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0c10 ProdID=0000 Rev=15.00
S:  Manufacturer=SiW
S:  Product=SiW
S:  SerialNumber=340A05F61100
C:* #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr= 50mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NPeter Poklop <peter.poklop@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

debugfs_create_bool is asking to put u32 type pointer instead of bool
so that passing bool type with u32* cast will cause memory corruption
to read that value since it is handled by 4 bytes instead of 1 byte
inside.
Signed-off-by: NBen Young Tae Kim <ytkim@qca.qualcomm.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The kbuild test robot reported implicit declaration of function
'acpi_dev_get_resources'.

Surround ACPI function by CONFIG_ACPI test.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NFrederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

devm_gpiod_get currently has an optional parameter to set initial
direction and value for the requested gpio. Make use of this to simplify
the driver and make it not fail to build when this parameter is made
mandatory (which is scheduled for 4.3-rc1).

Moreover use the _optional variant of devm_gpiod_get to simplify error
handling (which also gets more strict for free).
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add reference to hci_uart structure to bcm_device.
This allows suspend/resume callbacks to manage UART flow control.
Signed-off-by: NFrederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Parse platform_device's ACPI to retrieve UART init speed.
When BCM device is open, check if its TTY has same parent as one of the
platform devices saved. If yes, use platform_device's init speed.
Signed-off-by: NFrederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Retrieve "shutdown" and "device_wakeup" GPIOs from ACPI.
Set device off during platform device enumeration.
Set device on only when attached.
As driver can be unbound we need to check if the bcm_device still exists
before calling GPIO's functions, this is protected using device_list_lock.
Signed-off-by: NFrederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

QCA61x4 chips have supported sleep feature using In-Band-Sleep commands
to enable sleep feature based on H4 protocol. After sending
patch/nvm configuration is done, IBS mode will be up and running
Signed-off-by: NBen Young Tae Kim <ytkim@qca.qualcomm.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This is for supporting BT for QCA ROME with vendor specific
HCI commands and initialization on the chip. This will have
USB/UART implementation both, but for now, adding UART vendor
specific commands to patch downloading and set Bluetooth device
address using vendor specific command.
Signed-off-by: NBen Young Tae Kim <ytkim@qca.qualcomm.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

We will not release sdio bus until firmware is completely
downloaded and becomes ready. Our 8887 A2 chip can have
separate firmware images for WLAN and bluetooth. This
patch fixes an issue observed when both drivers
simultaneously try to download respective firmwares.
Signed-off-by: NAniket Nagarnaik <aniketn@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

btusb currently has a generic match on USB device descriptors:
        { USB_DEVICE_INFO(0xe0, 0x01, 0x01) },

However, http://www.usb.org/developers/defined_class states:

  Base Class E0h (Wireless Controller)
  This base class is defined for devices that are Wireless controllers.
  Values not shown in the table below are reserved. These class codes are
  to be used in Interface Descriptors, with the exception of the Bluetooth
  class code which can also be used in a Device Descriptor.

Add a match on the interface descriptors accordingly.

This fixes compatibility with the RTL8723AU device shown below.
This device conforms to the USB Interface Association Descriptor
specification, which requires the device to have class ef/02/01.
The extra IAD descriptor then specifies that interfaces 0 and 1
belong to the same function/driver, which is true. Provided that
the Bluetooth device class spec accepts use of the IAD, I imagine that
technically, all btusb devices should be configured like this.

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  3 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0bda ProdID=0724 Rev= 2.00
S:  Manufacturer=Realtek
S:  Product=802.11n WLAN Adapter
S:  SerialNumber=00e04c000001
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=500mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 4 Cls=ff(vend.) Sub=ff Prot=ff Driver=rtl8723au
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=03(Int.) MxPS=  64 Ivl=500us
Signed-off-by: NDaniel Drake <drake@endlessm.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add "waiting for configuration" address.
Add lmp_subver and firmware name for BCM4330B1 controller.
Signed-off-by: NFrederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Cleanedup "Unnecessary space before function pointer arguments" warning
reported by Checkpatch
Signed-off-by: NPrasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Fix for Cleanpatch warning:
Space prohibited between function name and open parenthesis '('
Signed-off-by: NPrasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Fix for "Unnecessary space before function pointer arguments" reported
by checkpatch.
Signed-off-by: NPrasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Remove semicolon in switch statement, reported by coccinelle
Signed-off-by: NPrasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Intel version information is shared between USB and UART drivers
and with that move it into a generic function of the Intel module.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The Intel Secure Send command is used the same in USB and UART drivers
and with that move a generic version into the Intel module.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>