This patch removes the buffering of the status register.
USB core behavior has changed a bit and this buffering was not refreshed
at the right time.  The core got buffered old value of HCRHPORT and it
did not detect any devices on boot.
Signed-off-by: NAnti Sullin <anti.sullin@artecdesign.ee>
Acked by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The purpose of this patch is to split off the case when a device does
not reply on the lower level (which is reported by HC hardware), and
a case when the device accepted the request, but does not reply at
upper level. This redefinition allows to diagnose issues easier,
without asking the user if the -110 happened "immediately".

The usbmon splits such cases already thanks to its timestamp, but
it's not always available.

I adjusted all drivers which I found affected (by searching for "urb").
Out of tree drivers may suffer a little bit, but I do not expect much
breakage. At worst they may print a few messages.
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The attached patch makes a cleanup of isp116x-hcd. Most of the volume of
the patch comes from 2 sources: moving the code around to get rid of a
few function prototypes and reworking register dumping functions/macros.
Among other things, switched over from using procfs to debugfs.

Cleanup. The following changes were made:

- Rework register dumping code so it can be used for dumping
  to both syslog and debugfs.
- Switch from procfs to debugfs..
- Die gracefully on Unrecoverable Error interrupt.
- Fix memory leak in isp116x_urb_enqueue(), if HC happens to
  die in a narrow time window.
- Fix a 'sparce' warning (unnecessary cast).
- Report Devices Removable for root hub ports by default
  (was Devices Permanently Attached).
- Move bus suspend/resume functions down in code to get rid of
  a few function prototypes.
- A number of one-line cleanups.
- Add an entry to MAINTAINERS.
Signed-off-by: NOlav Kongas <ok@artecdesign.ee>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

 MAINTAINERS                    |    6
 drivers/usb/host/isp116x-hcd.c |  429 ++++++++++++++++-------------------------
 drivers/usb/host/isp116x.h     |   83 +++++--
 3 files changed, 230 insertions(+), 288 deletions(-)

This makes the isp116x driver stop using usb_suspend_device() and
usb_resume_device() ... usbcore now calls to the root hub methods,
removing the need for this.  It also switches from keventd to khubd
for remote wakeup.  (Compile tested.)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/host/isp116x-hcd.c |   29 ++++-------------------------
 drivers/usb/host/isp116x.h     |    1 -
 2 files changed, 4 insertions(+), 26 deletions(-)

This patch provides an "isp116x-hcd" driver for Philips'
ISP1160/ISP1161 USB host controllers.

The driver:
 - is relatively small, meant for use on embedded platforms.
 - runs usbtests 1-14 without problems for days.
 - has been in use by 6-7 different people on ARM and PPC platforms,
   running a range of devices including USB hubs.
 - supports suspend/resume of both the platform device and the root hub;
   supports remote wakeup of the root hub (but NOT the platform device)
   by USB devices.
 - does NOT support ISO transfers (nobody has asked for them).
 - is PIO-only.
Signed-off-by: NOlav Kongas <ok@artecdesign.ee>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>