There was a deadlock between master I2C adapter and muxed I2C
adapter. Implement two I2C muxed I2C adapters and leave master
alone, just only for offering I2C adapter for these mux adapters.
Reported-by: NLuis Alves <ljalvs@gmail.com>
Reported-by: NBenjamin Larsson <benjamin@southpole.se>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

RTL2832 provides gated / repeater I2C adapter for tuner.
Implement it as a muxed I2C adapter.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Most of those were reported by checkpatch.pl...

debug module parameter is not used anywhere so remove it.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

All used tuners has get_if_frequency() callback and that parameter
is not needed and will not needed as all upcoming tuner drivers
should implement get_if_frequency().
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Disable IR interrupts in order to avoid SDR sample loss.
IR interrupts causes some extra load for device and it seems
be one reason to loss samples when sampling rate is high.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

There is now new tuner types which are not handled on that switch-case.
Print error if unknown tuner type is meet.

drivers/media/tuners/tuner-xc2028.c: In function ‘generic_set_freq’:
drivers/media/tuners/tuner-xc2028.c:1037:2: warning: enumeration value ‘V4L2_TUNER_ADC’ not handled in switch [-Wswitch]
  switch (new_type) {
  ^
drivers/media/tuners/tuner-xc2028.c:1037:2: warning: enumeration value ‘V4L2_TUNER_RF’ not handled in switch [-Wswitch]

Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Some previous patch introduced this bug:

/devel/v4l/patchwork/Documentation/DocBook/controls.xml:2262: parser error : attributes construct error
	      <row id=""v4l2-mpeg-video-hor-search-range">
	                ^
/devel/v4l/patchwork/Documentation/DocBook/controls.xml:2262: parser error : Couldn't find end of Start Tag row line 2262
	      <row id=""v4l2-mpeg-video-hor-search-range">
	                ^
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add SDR to V3.15 revlist, and add the credits to Antti.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add SDR device type to v4l2-framework.txt document.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Let it be experimental still as all SDR drivers are in staging.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Document V4L2 SDR interface.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Update documentation to reflect 1 Hz frequency step flag.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Modulator ioctls could be enabled mistakenly for non-radio devices.
Currently those ioctls are only valid for radio. Fix it.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

VIDIOC_QUERYCAP IOCTL is used to query device capabilities. Add new
capability flag to inform given device supports SDR capture.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Acked-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Enable stream format (FMT) IOCTLs for SDR use. These are used for negotiate
used data stream format.

Reorganise some some IOCTL selection logic.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Acked-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Use own format ops for SDR data:
vidioc_enum_fmt_sdr_cap
vidioc_g_fmt_sdr_cap
vidioc_s_fmt_sdr_cap
vidioc_try_fmt_sdr_cap
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add new V4L2 stream format definition, V4L2_BUF_TYPE_SDR_CAPTURE,
for SDR receiver.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add V4L2_TUNER_CAP_1HZ for 1 Hz resolution.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Define tuner types V4L2_TUNER_ADC and V4L2_TUNER_RF for SDR usage.

ADC is used for setting sampling rate (sampling frequency) to SDR
device.

Another tuner type, named as V4L2_TUNER_RF, is possible RF tuner.
Is is used to down-convert RF frequency to range ADC could sample.
Having RF tuner is optional, whilst in practice it is almost always
there.

Also add checks to VIDIOC_G_FREQUENCY, VIDIOC_S_FREQUENCY and
VIDIOC_ENUM_FREQ_BANDS only allow these two tuner types when device
type is SDR (VFL_TYPE_SDR). For VIDIOC_G_FREQUENCY we do not check
tuner type, instead override type with V4L2_TUNER_ADC in every
case (requested by Hans in order to keep functionality in line with
existing tuners and existing API does not specify it).

Prohibit VIDIOC_S_HW_FREQ_SEEK explicitly when device type is SDR,
as device cannot do hardware seek without a hardware demodulator.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add new V4L device type VFL_TYPE_SDR for Software Defined Radio.
It is registered as /dev/swradio0 (/dev/sdr0 was already reserved).
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add new video4linux device named /dev/swradio for Software Defined
Radio use. V4L device minor numbers are allocated dynamically
nowadays, but there is still configuration option for old fixed style.
Add note to mention that configuration option too.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This device has a led at bit 7 of GPIO reg. 0x80 to indicate
when a DVB capture is happening.

Add support for it.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Some devices have a LED to indicate when DVB capture started.
Add support for it.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This device is close to Kworld UB435-Q, but it uses a different
tuner. Add support for it.

Tested with both 8VSB and 256QAM modulations.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

tda18272 is programmed just like tda18212, but it also
supports ClearQAM and ATSC.

Add support for them. Tested with a Kworld UB435-Q on both
8VSB and 256QAM modes.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Some boards got added there. Update the cardlist to reflect the
current status.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Some new boards got added. Update the cardlist.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Currently, there's just one device using this frontend: PCTV 80e,
and it works on serial mode.

Change the default here to serial mode. If we add more devices,
then this option should be set via config structure.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The cfg_mpeg_output has more fields than what it is initialized
when the code is called. Be sure to initialize everything before
use, in order to avoid random behaviors.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Just like the windows driver, disable OOB after setting the driver
version.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

DJH_DEBUG only code path in drxbsp_i2c_write_read() dereferences
w_dev_addr and subsequently w_dev_addr->user_data->i2c which results
in failure during boot. This patch fixes the null pointer derefence
bug as well as the following compile errors:

  LD      arch/x86/built-in.o
  CC      drivers/media/dvb-frontends/drx39xyj/drxj.o
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function ‘drxbsp_i2c_write_read’:
drivers/media/dvb-frontends/drx39xyj/drxj.c:1558:25: error: redeclaration of ‘state’ with no linkage
  struct drx39xxj_state *state = w_dev_addr->user_data;
                         ^
drivers/media/dvb-frontends/drx39xyj/drxj.c:1512:25: note: previous declaration of ‘state’ was here
  struct drx39xxj_state *state;
                         ^
drivers/media/dvb-frontends/drx39xyj/drxj.c:1558:2: warning: ISO C90 forbids mixed declarations and code [-Wdeclaration-after-statement]
  struct drx39xxj_state *state = w_dev_addr->user_data;
  ^
drivers/media/dvb-frontends/drx39xyj/drxj.c:1560:17: error: redeclaration of ‘msg’ with no linkage
  struct i2c_msg msg[2] = {
                 ^
drivers/media/dvb-frontends/drx39xyj/drxj.c:1513:17: note: previous declaration of ‘msg’ was here
  struct i2c_msg msg[2];
                 ^
Signed-off-by: NShuah Khan <shuah.kh@samsung.com>
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

drxbsp_i2c_write_read() has return that prevents DJH_DEBUG code to run.
Remove it.
Signed-off-by: NShuah Khan <shuah.kh@samsung.com>
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

drxj.c fails to compile with the following errors when DJH_DEBUG
is defined.

drivers/media/dvb-frontends/drx39xyj/drxj.c:1567:2: error: implicit declaration of function ‘pr_dbg’ [-Werror=implicit-function-declaration]
  pr_dbg("drx3933 i2c operation addr=%x i2c=%p, wc=%x rc=%x\n",
  ^
Signed-off-by: NShuah Khan <shuah.kh@samsung.com>
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Mimic what windows driver does here: it writes 0x07 to
SIO_CC_SOFT_RST__A, instead of just 0x03.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

As drxj_close puts the device in powerdown, we need to power it up
properly at drxj_open.

This is the behavior noticed at the Windows driver.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

There are no other I2C masters here. Also, the Windows driver uses
this mode (and both drxd and drxk Kernel drivers). So, switch
to it.

That helps to compare the logs between the Linux driver and the
Windows one.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Instead of just disabling the LNA every time, allow to control it from
userspace.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

On several places, the I2C functions are just wrappers to others.

Get rid of it.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This struct contains the first abstraction layer for the I2C
access routines. Get rid of it.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This file contains an abstract layer for the I2C transfer
functions. Get rid of it, merging it at drxj. This will allow
to remove another abstraction layer there, making the code
easier to read, and removing the functions that just return
-EIO.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>