almost no users in the tree; and the few that use them treat them
like NET_RX_DROP.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bit that tells us whether a statistics counter snapshot operation
has completed is located in the GLOBAL register block, not in the
GLOBAL2 register block, so fix up mv88e6xxx_stats_wait() to poll the
right register address.
Signed-off-by: NStephane Contri <Stephane.Contri@grassvalley.com>
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Cc: stable@kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eric Dumazet a écrit :
> Ingo Molnar a écrit :
>>> The following changes since commit 52989765:
>>>   Linus Torvalds (1):
>>>         Merge git://git.kernel.org/.../davem/net-2.6

> >>> are available in the git repository at:

>>>   master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6.git master
>> Hm, something in this lot quickly wrecked networking here - see the
>> tx timeout dump below. It starts with:
>>
>> [  351.004596] WARNING: at net/sched/sch_generic.c:246 dev_watchdog+0x10b/0x19c()
>> [  351.011815] Hardware name: System Product Name
>> [  351.016220] NETDEV WATCHDOG: eth0 (forcedeth): transmit queue 0 timed out
>>
>> Config attached. Unfortunately i've got no time to do bisection
>> today.
>
>
>
> forcedeth might have a problem, in its netif_wake_queue() logic, but
> I could not see why a recent patch could make this problem visible now.
>
> CPU0/1: AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02
> is not a new cpu either :)
>
> forcedeth uses an internal tx_stop without appropriate barrier.
>
> Could you try following patch ?
>
> (random guess as I dont have much time right now)

We might have a race in napi_schedule(), leaving interrupts disabled forever.
I cannot test this patch, I dont have the hardware...
Tested-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The call resource_size(res) returns res->end - res->start + 1 and thus the
second change is semantics-preserving.  res_size is then used as the second
argument of a call to request_mem_region, and the memory allocated by this
call appears to be the same as what is released in the two calls to
release_mem_region.  So the size argument for those calls should be
resource_size(size) as well.  Alternatively, in the second call to
release_mem_region, the second argument could be res_size, as that variable
has already been initialized at the point of this call.

The problem was found using the following semantic patch:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
struct resource *res;
@@

- (res->end - res->start) + 1
+ resource_size(res)

@@
struct resource *res;
@@

- res->end - res->start
+ BAD(resource_size(res))
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

add new id (RIOS System PC CARD3 ETHERNET).
Signed-off-by: NKen Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch properly defines the maximum values for rx/tx coalescing timeouts.
Signed-off-by: NVlad Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Problem reported by Flavio Leitner <fleitner@redhat.com>:
When setting rx/tx coalescing timeout to the values less than 12 traffic was
stopped.

The FW supports coalescing in 12us granularity, and so value of less then 12
should be interpreted as disabling coalescing
Signed-off-by: NVlad Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is currently possible for an asynchronous device unregister
to cause the same tun device to be unregistered twice.  This
is because the unregister in tun_chr_close only checks whether
__tun_get(tfile) != NULL.  This however has nothing to do with
whether the device has already been unregistered.  All it tells
you is whether __tun_detach has been called.

This patch fixes this by using the most obvious thing to test
whether the device has been unregistered.

It also moves __tun_detach outside of rtnl_unlock since nothing
that it does requires that lock.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 537a1bf0 (fbdev: add mutex for
fb_mmap locking) introduces a ->mm_lock mutex for protecting smem
assignments. Unfortunately in the case of sm501fb these happen quite
early in the initialization code, well before the mutex_init() that takes
place in register_framebuffer(), leading to:

   Badness at kernel/mutex.c:207

   Pid : 1, Comm:          swapper
   CPU : 0                 Not tainted  (2.6.31-rc1-00284-g529ba0d9-dirty #2273)

   PC is at __mutex_lock_slowpath+0x72/0x1bc
   PR is at __mutex_lock_slowpath+0x66/0x1bc
   ...

matroxfb appears to have the same issue and has solved it with an early
mutex_init(), so we do the same for sm501fb.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6: (27 commits)
  parisc: use generic atomic64 on 32-bit
  parisc: superio: fix build breakage
  parisc: Fix PCI resource allocation on non-PAT SBA machines
  parisc: perf: wire up sys_perf_counter_open
  parisc: add task_pt_regs macro
  parisc: wire sys_perf_counter_open to sys_ni_syscall
  parisc: inventory.c, fix bloated stack frame
  parisc: processor.c, fix bloated stack frame
  parisc: fix compile warning in mm/init.c
  parisc: remove dead code from sys_parisc32.c
  parisc: wire up rt_tgsigqueueinfo
  parisc: ensure broadcast tlb purge runs single threaded
  parisc: fix "delay!" timer handling
  parisc: fix mismatched parenthesis in memcpy.c
  parisc: Fix gcc 4.4 warning in lba_pci.c
  parisc: add parameter to read_cr16()
  parisc: decode_exc.c should include kernel.h
  parisc: remove obsolete hw_interrupt_type
  parisc: fix irq compile bugs in arch/parisc/kernel/irq.c
  parisc: advertise PCI devs after "assign_resources"
  ...

Manually fixed up trivial conflicts in tools/perf/perf.h due to addition
of SH vs HPPA perf-counter support.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
  mfd: fix pcap adc locking
  mfd: sm501, fix lock imbalance

* 'for-2.6.31' of git://linux-nfs.org/~bfields/linux:
  NFSD: Don't hold unrefcounted creds over call to nfsd_setuser()

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  MIPS: Fix CONFIG_FLATMEM version of pfn_valid()
  MIPS: Reorganize Cavium OCTEON PCI support.
  Update Yoichi Yuasa's e-mail address
  MIPS: Allow suspend and hibernation again on uniprocessor kernels.
  MIPS: 64-bit: Fix o32 core dump
  MIPS: BC47xx: Fix SSB irq setup
  MIPS: CMP: Update sync-r4k for current kernel
  MIPS: CMP: Move gcmp_probe to before the SMP ops
  MIPS: CMP: activate CMP support
  MIPS: CMP: Extend IPI handling to CPU number
  MIPS: CMP: Extend the GIC IPI interrupts beyond 32
  MIPS: Define __arch_swab64 for all mips r2 cpus
  MIPS: Update VR41xx GPIO driver to use gpiolib
  MIPS: Hookup new syscalls sys_rt_tgsigqueueinfo and sys_perf_counter_open.
  MIPS: Malta: Remove unnecessary function prototypes
  MIPS: MT: Remove unnecessary semicolons
  MIPS: Add support for Texas Instruments AR7 System-on-a-Chip

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  sound: do not set DEVNAME for OSS devices
  ALSA: hda - Add sanity check in PCM open callback
  ALSA: hda - Call snd_pcm_lib_hw_rates() again after codec open callback
  ALSA: hda - Avoid invalid formats and rates with shared SPDIF
  ALSA: hda - Improve ASUS eeePC 1000 mixer
  ALSA: hda - Add GPIO1 control at muting with HP laptops
  ALSA: usx2y - reparent sound device
  ALSA: snd_usb_caiaq: reparent sound device
  sound: virtuoso: fix Xonar D1/DX silence after resume
  ASoC: Only disable pxa2xx-i2s clocks if we enabled them
  ALSA: hda - Add quirk for HP 6930p
  ALSA: hda - Add missing static to patch_ca0110()
  ASoC: OMAP: fix OMAP1510 broken PCM pointer callback
  ASoC: remove BROKEN from Efika and pcm030 fabric drivers
  ASoC: Fix typo in MPC5200 PSC AC97 driver Kconfig

* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
  kbuild: finally remove the obsolete variable $TOPDIR
  gitignore: ignore scripts/ihex2fw
  Kbuild: Disable the -Wformat-security gcc flag
  gitignore: ignore gcov output files
  kbuild: deb-pkg ship changelog
  Add new __init_task_data macro to be used in arch init_task.c files.
  asm-generic/vmlinux.lds.h: shuffle INIT_TASK* macro names in vmlinux.lds.h
  Add new macros for page-aligned data and bss sections.
  asm-generic/vmlinux.lds.h: Fix up RW_DATA_SECTION definition.

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  block: don't merge requests of different failfast settings
  cciss: Ignore stale commands after reboot

Occasionally we may see an interrupt without an event in the eq.
In intx, we currently see the event queue and return IRQ_NONE causing
a the irq to be disabled ("no one cared".) Instead, read the CEV_ISR
reg to check the existence of the interrupt.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This workaround is required for an issue in hardware where noise on the
interconnect between the MAC and PHY could be generated by a lower power
mode (K1) at 1000Mbps resulting in bad packets.  Disable K1 while at 1000
Mbps but keep it enabled for 10/100Mbps and when the cable is disconnected.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some PHYs may require two reads of the PHY_STATUS register to determine the
link status.  If the PHY is being accessed by another thread it is possible
the first read could timeout and fail.  In this case, put a delay in so
the second read will pick up the correct link status.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Limit NVM writes to 4K sections to prevent NVM corruption on larger
sector allocations (up to 64K).
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver was accessing register bits for features on parts that do
not support that feature.  This could cause problems in the hardware.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A previous workaround for 82578 to avoid link stall causes some PHY
registers to get cleared inadvertently.  Add a delay after all LCD resets
to make sure PHY registers are in a stable state before continuing.  Also,
after resets check the EEC register for the state of PHY configuration
performed by the MAC for ICH9 and earlier parts (as done before), but check
the LAN_INIT_DONE bit in the STATUS register for ICH10 and newer parts (EEC
doesn't exist in these newer parts).
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PHY loopback on 82578 fails to work as a result of flushing the packets
in the FIFO buffer in the link stall workaround.  Don't perform the
workaround if in PHY loopback mode.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Wake-on-lan is currently only supported by 82599 KX4 devices, in all
other cases return a proper value from ixgbe_wol_exclusion function call.
Otherwise from ethtool we will be able to change wol options of
unsupported 8259x devices.
Signed-off-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently if we loaded the driver, insert an unsupported module, and then
attempt to "ifconfig up" the device it will be brought down but the netdev
would not be unregistered. This behavior is different than all other
code paths. This patch corrects that by down'ing the device and then
scheduling the sfp_config_module_task tasklet. The tasklet will detect
this condition (like it does with other code paths) and do the
unregister_netdev().

I also removed the log message as this condition (an unsupported SFP+
module) will be logged in sfp_config_module_task.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The change to check the SFP+ module again on open() was
causing the XFP (non-SFP+) adapters to be rejected. We
only want to try and re-identify the SFP+ module if the
original probe found that this device was an SFP+ device.
So for this code path (driver loaded with SFP module, module
inserted, ifconfig up of the device) the type will be
ixgbe_phy_unknown for an unidentified SFP+ module.  So we
only check if that is the case.

This problem also shows up on Copper devices.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several small fixes around negative test case of the insertion of a
IXGBE_ERR_NOT_SUPPORTED module.

- mdio45_probe call was always failing due to mdio.prtad not being
set.  The function set to mdio.mdio_read was still working as we just
happen to always be at prtad == 0.  This will allow us to set the phy_id
and phy.type correctly now.

- There was timing issue with i2c calls when initiated from a tasklet.
A small delay was added to allow the electrical oscillation to calm down.

- Logic change in ixgbe_sfp_task that allows NOT_SUPPORTED condition
to be recognized.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some usage was only sizing a pointer rather than the data type.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to set/clear the mac address register when the link goes up/down
respectively.  Without this both ports of a 2-port device can end up
with the same mac address in a bonding scenario.
The new ql_link_on() and ql_link_off() will also be used in handling
certain firmware events.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This addes functionality to set/clear the MAC address in the hardware
when the link goes up/down.
The MAC address register is persistent across function resets. In
bonding the same address can bounce from one port to the other.  This
can cause packets to be delivered to the wrong port.
This patch clears the MAC address in the hardware when the link is down
and sets it when the link comes up.
It was found that pulling/pushing the cable from one port to another
causes the same MAC address to be in both ports.
The next patch in this series will use this functionality as well.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The caller will free acquired resouces if a failure occurs.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We were turning on the carrier without verifying the link was up.
This adds link up to the link initialize check before turning carrier
on.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Not clearing the routing bits can cause frames to erroneously get routed to
management processor.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hardware semaphore covers the configuration register as well as the
ICB registers.  The ICB high and low regs contain the address of the
initialization control block and the config register is used to signal
the hardware that a block is ready to be downloaded.  Currently we were
only protecting the ICB regs.  This changes expands to cover the config
register as well.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's a bug in addrconf_prefix_rcv() where it won't update the
preferred lifetime of an IPv6 address if the current valid lifetime
of the address is less than 2 hours (the minimum value in the RA).

For example, If I send a router advertisement with a prefix that
has valid lifetime = preferred lifetime = 2 hours we'll build
this address:

3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000
    inet6 2001:1890:1109:a20:217:8ff:fe7d:4718/64 scope global dynamic
       valid_lft 7175sec preferred_lft 7175sec

If I then send the same prefix with valid lifetime = preferred
lifetime = 0 it will be ignored since the minimum valid lifetime
is 2 hours:

3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000
    inet6 2001:1890:1109:a20:217:8ff:fe7d:4718/64 scope global dynamic
       valid_lft 7161sec preferred_lft 7161sec

But according to RFC 4862 we should always reset the preferred lifetime
even if the valid lifetime is invalid, which would cause the address
to immediately get deprecated.  So with this patch we'd see this:

5: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000
    inet6 2001:1890:1109:a20:21f:29ff:fe5a:ef04/64 scope global deprecated dynamic
       valid_lft 7163sec preferred_lft 0sec

The comment winds-up being 5x the size of the code to fix the problem.

Update the preferred lifetime of IPv6 addresses derived from a prefix
info option in a router advertisement even if the valid lifetime in
the option is invalid, as specified in RFC 4862 Section 5.5.3e.  Fixes
an issue where an address will not immediately become deprecated.
Reported by Jens Rosenboom.
Signed-off-by: NBrian Haley <brian.haley@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SCTP pushed the skb above the sctp chunk header, so the
check of pskb_may_pull(skb, nh + offset + 1 - skb->data) in
_decode_session6() will never return 0 and the ports decode
of sctp will always fail. (nh + offset + 1 - skb->data < 0)
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SCTP pushed the skb data above the sctp chunk header, so the check
of pskb_may_pull(skb, xprth + 4 - skb->data) in _decode_session4() will
never return 0 because xprth + 4 - skb->data < 0, the ports decode of
sctp will always fail.
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>